Air bag light on Ford Escape?

The most common reason for the airbag light to be on is because the car had its airbag deployed so if You have not had that happen or disconnected the battery You should take it to a dealership to make sure there are no other problems involving the airbag.

What can cause the airbag light to come on?

What causes the airbag light to come on?

  • The airbag needs resetting.
  • Corroded sensors.
  • Depleted battery.
  • Dislodged wiring.
  • Faulty seat belt.
  • Your airbag clock spring may need replacing.

How do you reset the airbag light on a Ford?

Switch the auto key on the ignition switch. Wait until the warning light on the airbag turns off. Turn your car’s ignition switch back off for just over three seconds. Repeat steps 1 through 3 twice, making a total of three times.

Why is my airbag light on all of a sudden?

When this light is on, that means your airbags are deactivated. It means they will not deploy properly if you get into an accident. If your car’s battery has drained recently, it may have also depleted the backup battery that powers the airbags.

How do I get the airbag light off my dashboard?

How to Reset an Airbag Light

  1. Put the key into the ignition and turn the switch to the “on” position.
  2. Watch for the airbag light to turn on. It will stay illuminated for seven seconds and then shut itself off. After it shuts off, immediately turn the switch off and wait three seconds.
  3. Repeat Steps 1 and 2 two more times.

Can I drive my car if the airbag light is on?

When the airbag light illuminates, it means that there is a problem with the system. Most likely, the airbag will not deploy in an accident because of this fault. While it doesn’t mean the car is unsafe to drive, there’s no reason to take chances with it.

How much does it cost to fix a airbag light?

Number 1 — Reset Airbag Light You’ll need to hire a professional to come in and examine the airbags before you continue to drive the car. This process can take several hours of time and usually costs a few hundred dollars, although depending upon the type of car it may be up to about $600.

How do you turn off the airbag light on a Ford Escape?

To reset the airbag light in a Ford Escape You can follow these directions listed here – Step 1 insert the key into the ignition and turn the switch to “on”. Step 2 Pay attention tot he light as it will illuminate for seven seconds and then shut off. After the shut off turn the ignition off and wait for 3 seconds.

Can you reset airbag light without tool?

In some older cars, though, it is possible to reset the airbag light without a scanner by removing the car battery terminals. Check the wiring system underneath the driver or passenger seat for any loose wires or corrosion in the connector plug. Spray the connector plugs with an electronic cleaner and restart your car.

Will disconnecting battery reset airbag light?

No, this information is stored in non volatile memory. The airbag light is usually on if there’s a problem with the system. Even if you could clear the code which is reporting that, if the problem isn’t fixed then it will just be detected again, and the light will come back on.

Can a blown fuse cause the airbag light to come on?

Blown fuses can definitely cause the airbag light to come on. When the airbag system is malfunctioning, a mechanic or auto parts store should be able to read the code that the system is putting out which will give them a clue as to what particular problem the airbag is having.

Can an airbag warning light be reset?

An airbag warning light can not turn itself off and has to be manually reset. When an airbag light comes on, there is something wrong with the airbag system. Nevertheless, you will need to manually reset the airbag system after you fix the problem.

How do I know if my airbag sensor is bad?

Symptoms of a failing airbag sensor You can easily tell if the sensor is functioning if the airbag warning light on the dashboard is illuminating every time you start the vehicle. But, if the airbag warning light stays illuminated after starting the vehicle, this is an indication of an airbag sensor problem.

How do I turn my airbag off?

But the passenger airbag can be deactivated if the car is equipped with a Passenger Airbag Cut Off Switch (PACOS). In most cases, to disable the airbag you need to have the ignition switched off to avoid any possible malfunctions. The PACOS is usually located in the passenger side of the dash board.

Where is the airbag sensor?

An impact sensor is normally fitted to the front of the vehicle as this is where a collision is likely to occur. The sensor is positioned inside the engine and a similar safety sensor is located inside the passenger zone of the vehicle.

Is airbag light a MOT failure?

During your MOT your vehicle’s airbags will be checked. If your car’s airbag warning light is on during your MOT, you will need to schedule a second visit. In fact, this indicator light is considered a major reason to fail your MOT, since it directly impacts your safety.

Ford Escape: Airbag Light Stays On Diagnosis

Cookies are used on this website to customise your content (including advertisements) and to evaluate our traffic. More information on cookies may be found here. The fact that you are still using our site indicates that you agree to our Terms of Service and Privacy Policy.

Ford Escape Airbag Light on Causes

Your Escape’s airbag light is part of a bigger supplementary restraint system that includes other components. It works in conjunction with the rest of the system to keep you safe in the case of an accident. In the event that all components of this system are not functioning properly, the airbag light may illuminate. The airbag light will remain illuminated after an accident until the system has been fully repaired or replaced. It will not function until it has been fixed. Here are some of the most common reasons why the airbag light on your Escape may illuminate.

1.Seat Belts

In the event that your Escape crashes, safety belts are still the most vital safety item to have. Modern automobiles are equipped with sensors that communicate with the computer system to determine whether or not they are strapped and whether or not they are locked up. If you have a seat belt that is caught in the lock position, it is possible that this is the cause of your airbag light turning on. Check to see if you can get it going again by tugging on it.

2.Seat Sensors

The airbag system is alerted when the seat sensors detect that the seat is occupied. Some older model automobiles feature a manual button that may be used to switch on or off the passenger airbag. Look behind the seats to see if you can identify any parts of the wiring harness that have been loose or damaged as a result of the accident. This is one of the most typical reasons why the airbag light illuminates.

3.Airbag Itself

The airbag system is informed of the presence of a person in the seat via the seat sensors. Manually activating or deactivating the passenger airbag is available in certain older model automobiles. Look behind the seats to see if there is any portion of the wire harness that has become dislodged or damaged during the process. Getting the airbag light to illuminate is a pretty usual cause of it.

4.Airbag ECU/Sensors

It’s possible that the control unit for the airbag system has failed. It is possible to get it replaced or to request a new one in this situation. This is common when you are involved in a fender accident that does not result in the deployment of the airbag. It’s possible that one or more of the collision sensors were activated, but not enough to cause the airbag to deploy. It is also possible for the airbag sensors to fail and illuminate the airbag light if there is water damage. This is one of the reasons why it is not a good idea to purchase an automobile that has flood damage, even if it appears to be in otherwise good condition.

5.Not Reset After Deployment

A malfunctioning control unit for the airbag system might have occurred. It is possible to get it replaced or to request a new one in this situation. In many cases, this occurs when you are involved in a minor collision in which the airbag does not deploy. The airbag may have been deployed because one or more of the crash sensors were activated, but not all of them.

Similarly, if there is water damage to the airbag sensors, the airbag light will on. For this reason, even if the automobile appears to be in excellent condition otherwise, it is not a good idea to purchase one with flood damage.

Is it Safe to Drive Your Escape with the Airbag Light On?

Driving with the airbag light illuminated is not as safe as it should be. Since its inception, the airbag system has saved a vast number of lives. If you choose to drive with your Escape’s airbag light illuminated, you are depending exclusively on the safety belts to keep you safe, which is not as safe as it may be in an accident. Almost all of the safety technology that saves you from crashing is still in place (assuming your vehicle is equipped with it), including traction control, anti-lock brakes, and blind spot recognition.

Conclusion:Ford Escape Airbag Light On

The airbag system in your Ford Escape is quite intricate. There are a variety of various reasons why the airbag light may have illuminated on your vehicle. The majority of them should be left in the hands of a professional. It is not enough that the car can be driven in order to dismiss the problem as unimportant. If you have anything to contribute, please leave a remark in the section below. Thanks for reading. Wishing you the best of luck!

See also:  Cranks but no start - GM?

2012 Ford Escape Airbag Warning Light – Truck Trend Garage

Question: In August, I acquired a 2012 Ford Escape from a private seller. Since then, the passenger airbag warning light has been intermittently on. It has been known to remain on for many minutes at a time. Other times, it will only flash once and then turn off completely. This occurs regardless of whether or not a passenger is present in the vehicle. I’m afraid that this will cause the airbag to deploy without notice. Answer:It sounds like you’re looking at the Passenger Airbag Deactivation (PAD) indication, which is located towards the center of the dashboard’s instrument panel.

  1. This is a component of the Occupant Classification System (OCS), which allows an airbag and seatbelt tensioner deployment strategy to be determined based on the weight of the occupant in the front passenger seat.
  2. As we all know, the backseat is the safest location for a kid, and the activation of an airbag on a newborn may be quite deadly.
  3. In all other circumstances, the indicator should be turned off completely.
  4. Several components, including the pressure sensor, the OCS module, the Restraints Control Module, and the seatbelt buckle switch, might be at fault, as could a faulty connection in any circuit connecting these components.
  5. The system of restraints in the 2012 Ford Escape is insured for 5 years or 60,000 kilometers.
  6. How to Get in Touch with Alex You can reach Alex, a master technician with the National Institute for Automotive Service Excellence, with any technical questions you may have about your truck, SUV, or van.
  7. Because of the large number of questions we get each month, we cannot promise that every question will be individually addressed or that every question will be published in the magazine.

Need assistance with an issue you’re having with your truck or SUV right away? Visit Alex Steele at for more information from the expert we trust here at Truck Trend Garage.

03 escape air bag light flashing .Help!

On April 1, 2011, at 12:07 p.m., Date of joining: July 2006 7,177 total posts If you had the actual DTC rather than an LFC (lamp flash code), it would be much easier to pinpoint the source of the problem and resolve it. Multiple reasons of air bag circuit difficulties, including high or low circuit resistance, or a shorting fault, can be found on the 36 (driver) or 37 (passenger) positions. Depending on whether or not your maintenance dealer worked on the system for the same code/s, you may be able to exert some pressure on them if the point is pushed, or they may give you a reduced-price repair.

  • What area or side, drivers/passengers, or whatever you want to call it.
  • Topics that are related ThreadThread StarterForum is a place where people may discuss threads.
  • EST makuloco2000Ford Focus001-19-201411:33 p.m.
  • makuloco2000Ford Focus001-19-201411:33 p.m.
  • makuloco2000Ford Focus001-19-201411:33 p.m.
  • There is a new member area.
  • on January 5, 2012.
  • 09:17 a.m.
  • 01:06 a.m.

How to Disengage the Airbags in a Ford Escape

Photograph by Christopher Meder for Fotolia.com of a microchipped car key. If you intend to work on the front seats or any components within the Ford Escape’s dashboard, steering column, or center console, you must first disconnect the air bag system before proceeding. Essentially, this is the initial stage in many repair operations, not only for the Ford Escape and other Ford cars, but also for any vehicle that is equipped with a functional supplementary restraint system. If you do not follow these instructions, you run the danger of activating the air bags while working on the Escape, and fixing the air bag system may be a complicated and expensive endeavor.

2005 Ford Escapes and Later

Turn off all of the devices in your Ford Escape’s interior. Make certain that the ignition is turned off as well.

Step 2

Shut off and unplug all of the devices in your Ford Escape. Don’t forget to turn off the ignition.

Step 3

Take the Restraints Control Module fuse out of the Smart Junction Box and place it somewhere safe. Consult your owner’s handbook or a Haynes Repair Manual for your specific model year for information on where to find the fuse in the first place.

Step 4

Insert your key into the ignition and turn the key to the “On” position. Keep an eye on the air bag warning light. If you turn off the RCM fuse, the air bag light will continue to illuminate.

It will not flash under any circumstances. If the light flashes or does not remain illuminated continuously, you must replace the fuse you pulled and then draw the right fuse again. Continue this procedure until the air bag light remains illuminated at all times.

Step 5

Remove the key from the ignition and turn off the vehicle’s electrical systems. Remove the negative cable from the battery by opening the Escape’s engine compartment. Replace the cable with a new one. Wait two to three minutes before continuing. There will still be some residual power left in the Escape, and you must allow it to exhaust itself.

Ford Escapes 2004 and Earlier

Check to verify that both of the front tires are facing squarely forward before continuing. Insert your key into the ignition and turn the key to the “Lock” position to secure the vehicle.

Step 2

Open the hood and have a look inside the engine compartment of the Escape.

Step 3

Remove the negative cable from the battery and set it aside. Wait two to three minutes for the remaining power in the car to be depleted before proceeding. References

  • In 2008, Mike Stubblefield and John H Haynes published “Haynes Repair Manual: Ford EscapeMazda Tribute: 2001 through 2007,” which is a repair manual for the Ford EscapeMazda Tribute from 2001 to 2007.

Bio of the AuthorRichard Ristow has been writing for magazines, newspapers, and internet since 2002. His work has appeared in the “2009 Nebula Showcase” as well as other publications. He is the recipient of the Rhysling Award from the Science Fiction Poetry Association, and he is an editor for Belfire Press, where he edits poetry. He also has a Master of Fine Arts degree from the University of North Carolina at Wilmington, and he formerly worked as a manager in the automobile section of a WalMart store.

More Articles

I very recently acquired this vehicle, perhaps a week and a half ago. I didn’t aware the airbag light was missing from the dash (I’m convinced the dealership removed it), and I had to return to the dealership to have it fixed because it is technically unlawful to allow a car to leave the lot without it. Also, the tire tread in the center was too thin and I had a check engine light on for a misfiring cylinder, which I had to ignore. We were able to get everything sorted out, however now the airbag light turned on.

  1. According to my study, this may be as easy as a problem with the cables beneath the seat (although this isn’t a code, so I’m not sure if it applies) or as complex as a complete system failure.
  2. I am completely clueless when it comes to automobiles, and the dealership is 45 minutes away, so I am unable to simply hop over there for a fast fix.
  3. However, my husband’s F-150 suddenly cost us approximately $1000, so I can’t simply take my car to my mechanic for fun and grins.
  4. With my previous car breaking down this past week, all of the troubles with this one, and then my husband’s truck problems, I’m completely exhausted, and so is my money account, which is also exhausted!

Why is the airbag light on in my Ford Escape? – Mysweetindulgence

It is also possible for the airbag sensors to fail and illuminate the airbag light if there is water damage.

This is one of the reasons why it is not a good idea to purchase an automobile that has flood damage, even if it appears to be in otherwise good condition. 5. The system is not reset after deployment. If your vehicle’s airbag has been deactivated and replaced, the airbag system must be re-activated.

What does the diagnostic warning light on Ford Explorer mean?

As soon as you turn on your Ford Explorer, the computer system does a self diagnostic check on all of the vehicle’s essential systems. If any of these tests fail, you will notice a diagnostic warning light illuminated on the instrument panel for the system that failed. This check is performed by the airbag system, and if it fails, the airbag light will illuminate.

Why does my airbag warning light go off when I Turn on the car?

At the outset of every journey in your Ford Explorer, the computer system performs a self-diagnosis of all important systems. Whenever one of these checks fails, a diagnostic warning light for the associated system will illuminate on the dash of the vehicle. The airbag light will illuminate if the airbag system fails this check.

How can I tell if my airbag sensor is working?

To evaluate whether or not the sensor is functioning properly, first look for the “Passenger Airbag Off” signal. This light should be turned on if the seat in front of you is empty. When the seat is occupied, the light should be turned off, indicating that the airbag system is online and operational, as expected. The sensor may be malfunctioning if the light turns off while the seat is unoccupied or the opposite is true when it turns on.

See also:  3.3L V6 Chrysler firing order?

How does the airbag warning light work on a Ford?

Check the “Passenger Airbag Off” sign first to see if the sensor is functioning properly. This light should be turned on if a seat is available. This should occur when the seat has been occupied, indicating that the airbag system is online and operating properly. The sensor may be malfunctioning if the light turns off while the seat is unoccupied or the opposite occurs.

When does the air bag light stop flashing?

The light will flash for exactly seven seconds after it is turned on. Once it is turned off, you must switch off the ignition within a second of turning it off. After three seconds, restart the engine by turning the key in the ignition again. After two or three repetitions of this procedure, the airbag light will be turned off permanently. You’ll be able to tell when it has been reset at this point. (Part I of a two-part series) How To Quickly and Easily Repair Your Airbag Light! To evaluate whether or not the sensor is functioning properly, first look for the “Passenger Airbag Off” signal.

When the seat is occupied, the light should be turned off, indicating that the airbag system is online and operational, as expected.

Why does my airbag light keep turning on?

To turn it off, you must first scan the system using a diagnostic tool and delete the soft-code fault. It is possible that a low car battery will cause the airbag light to illuminate. The spring is responsible for preserving continuity between the airbag in the driver’s seat and the electrical wire in the vehicle.

Ford Escape: Front passenger sensing system – Airbag Supplemental Restraint System (SRS) – Seating and Safety Restraints

This technology is meant to satisfy the regulatory criteria of Federal Motor Vehicle Safety Standard (FMVSS) 208 and is intended to deactivate (i.e., not inflate) the frontal airbag of a front seat passenger under specific circumstances. Several sensors, including those in the front passenger’s seat and safety belt, are used to operate the front passenger sensing system. A correctly seated occupant is detected by the sensors, which determines whether or not the front passenger’s frontal airbag should be activated (and hence potentially inflate) or disabled (and thus not inflate) (will not inflate).

A rear-facing infant seat that has been properly installed according to the manufacturer’s instructions is detected, a small child is detected in a forward-facing child restraint that has been properly installed according to the manufacturer’s instructions is detected, and a small child is detected in a booster seat is detected.

  1. A front passenger who has taken his/her weight off of the seat is detected.
  2. An indication for the passenger airbag off or pass airbag off is used by the front passenger sensing system to tell you that the passenger frontal airbag is not activated.
  3. The indication bulb is positioned in the middle stack of the instrument panel, directly above the air vents, and it illuminates while the engine is running.
  4. This bulb will not illuminate if there is no one sitting in the front passenger seat (an “empty seat”) or if the frontal airbag for the front passenger is activated (and may inflate).
  5. As a reminder that the front passenger frontal airbag has been deactivated by the front passenger sensing system (i.e.
  6. The vehicle should be turned off, the child restraint removed from the vehicle and the restraint reinstalled according to the child restraint manufacturer’s instructions if the child restraint has been placed but the indication bulb is not illuminated.
  7. When the front passenger sensing system activates the front passenger frontal airbag (which may inflate), the indicator will go out of service and remain out for a period of time.

In the event that this occurs: Turn off the car and instruct the occupant to raise the seatback to its full upright position before continuing.

Start the car and instruct the individual to remain in this position for approximately two minutes.

If the indication lamp continues to illuminate even after this, the individual should be instructed to travel in the backseat of the vehicle.

It is critical that all passengers maintain a good sitting position once they have adjusted their seats and fastened their safety belts, as well.

In the case of a collision, incorrect seating might increase the likelihood of injuries.

When you sit in an incorrect posture or with the seat back reclined too much, the weight of the seat cushion is taken away, which might impact the decision of the front passenger sensing system, which can result in serious injury or death in an accident.

Objects put on the seat cushion by the front passenger sensing system may be detected as little or medium in size.

Despite the fact that the passenger airbag has been disabled, the pass airbag off lamp may or may not be illuminated, depending on the conditions listed in the table below.

Other passengers or baggage may be pushing or tugging on the bottom cushion of the seat.

Because of the conditions stated in the preceding list, the individual in the front passenger seat may look heavier or lighter than usual.

Place nothing under the front passenger seat or between the seat and the center console, since this might cause a collision (if equipped).

Failure to adhere to these instructions may result in the front passenger seat sensing system becoming inoperative.

If the airbag readiness lamp is illuminated, do the following procedures: The driver and/or adult passengers should inspect the front passenger seat for any things that may be wedged below it or baggage that may be interfering with the seat’s operation.

Turn off the engine of the car.

Remove the stumbling block(s) (if found).

Continue to wait for at least two minutes and check to see whether the airbag readiness lamp has been extinguished.

DO NOT try to repair or service the system yourself; instead, take your vehicle to an authorized dealer as soon as possible.

The operation of the front passenger sensing system may be adversely affected if the front passenger seat has been altered or modified in any manner.

Determining if the system is operational

Front passenger sensing system is meant to satisfy the legal criteria of Federal Motor Vehicle Safety Standard (FMVSS) 208 and is designed to deactivate (inflate) the front passenger’s frontal airbag under specific situations. Front passenger sensing system The front passenger sensing system operates with the help of sensors that are integrated into the front passenger’s seat and safety belt assembly. A correctly seated occupant is detected by the sensors, which determines whether or not the front passenger’s frontal airbag should be activated (and hence potentially inflate) or disabled (and thus not inflate) (will not inflate).

A rear-facing infant seat that has been properly installed according to the manufacturer’s instructions is detected, a small child is detected in a forward-facing child restraint that has been properly installed according to the manufacturer’s instructions is detected, and a small child is detected in a booster seat is detected.

  1. A front passenger who has taken their weight off the seat is detected.
  2. An indication for the passenger airbag off or pass airbag off is used by the front passenger sensing system to tell you that the passenger frontal airbag is not activated.
  3. Located in the middle stack of the instrument panel, directly above the air vents, is the indicator lamp.
  4. When the front passenger seat is not occupied (empty seat), or in the case that the front passenger frontal airbag is engaged (and may inflate), the indication lamp will be turned off and not illuminate.
  5. It will glow and remain illuminated to alert you that the front passenger frontal airbag has been deactivated (i.e.
  6. will not inflate).
  7. A person of adult size is correctly seated in the front passenger seat when the front passenger sensing system detects this.

As soon as the front passenger sensing system allows the front passenger frontal airbag to deploy (and perhaps inflate), the indication will go out of service and remain out of service.

As a result of the occurrence, Shut off the car and instruct the occupant to fully extend the seatback to its highest position.

Continue to hold the person in this position for approximately two minutes after the car has been restarted.

It is recommended that the passenger travel in the back seat if the indication lamp remains illuminated after this.

It is critical that all passengers maintain good seating posture once they have adjusted their seats and fastened their safety belts.

In the case of an accident, incorrect seating might increase the risk of harm.

When you sit in an unsuitable position or with the seat back reclined too much, the weight of the seat cushion is taken away, which might alter the decision of the front passenger sensing system, which can result in serious damage or death in an accident.

Small or medium-sized objects put on the seat cushion by the front passenger sensing system may be detected.

Despite the fact that the passenger airbag has been disabled, the pass airbag off lamp may or may not be illuminated, depending on the conditions listed in the following table: Identify the following if you believe the “passenger airbag off” warning bulb is not in the proper state of operation: In the space between the seat cushion and the center console, there are objects that have been stuck (if equipped) Any items put on the occupant’s lap in the front passenger seat.

  1. Objects that may have jammed the safety belt against the seat or the passenger side b-pillar, preventing the safety belt from moving freely.
  2. Front seat passengers’ feet lying on or pressing on the bottom cushion of the seat.
  3. Because of the variables stated in the preceding list, the individual in the front passenger seat may appear to be heavier or lighter than usual.
  4. If a youngster is in the front passenger seat, do not stow anything in the seat back map pocket (if one is provided) or hang items from the seat back.
  5. Check for correct airbag status by looking for the “passenger airbag off” or “pass airbag off” signal lamp.
  6. A issue with the front passenger sensing system will result in the airbag readiness bulb in the instrument cluster remaining illuminated in this situation.
  7. It is necessary to take the following measures to remove things that have been stuck and/or cargo that is interfering with the seat.
  8. Off-ramp the car by using the button on the dash.
  9. Remove the object or objects that are causing the difficulty (if found).
  10. Wait at least two minutes and then check to see whether the airbag preparedness lamp has been turned off and is no longer on.
  11. Immediately take your car to an authorized dealer rather than attempting to repair or service the system.

The operation of the front passenger sensing system may be adversely affected if the front passenger seat has been altered or modified in any way.

See also:

When you are not towing a trailer, remove the ball mount from the hitch receiver tube and place the receiver cover into the hitch receiver tube to prevent damage to the ball mount. – Place the dust cap over the four-pin connector of the hitch wire harness and tighten it down with your fingers. System to Remind Drivers to Wear Their Seat Belts (BeltAlert) When the driver and front passenger (if the vehicle is equipped with front passengerBeltAlert) are not wearing their seat belts, BeltAlert is activated to remind them.

See also:  Ford Edge ABS light on?

DIC Buttons MENU: Selecting this button will take you to the Trip/Fuel Menu as well as the Vehicle Information Menu.

As the page is scrolled, a little marker will travel along it.

2013 Escape air bag light.Deysha please help!

12/26/13, 5:19 p.m. (EST) Bullitt MemberThread Starter is a thread starter for Bullitt members. Date of joining: July 4, 2012 Number of posts: 333 0 Likes have been received. 0 Likes 0 Dislikes 0 comments have been made. The air bag light on the 2013 Escape. Please, Deysha, lend a hand! Please let us know if anyone else has had this issue. My father recently purchased a 2013 Ford Escape Titanium. Every now and again, the air bag light illuminates for no apparent reason. The automobile, on the other hand, resets itself every time you switch it off.

  1. When I called the dealership, they told me that the light had to be turned on for them to do anything.
  2. While the light was still on, he promptly drove it back to the dealership to get it fixed.
  3. As a result, they accomplished nothing.
  4. He travels a long distance for business and is unable to just leave every time to go back to the dealership in order to keep the light on.
  5. It’s a spanking new automobile!
  6. Deysha, if you could just elevate this matter to the right party on my behalf, I would be really grateful.
  7. Please, someone assist me!

Date of joining: April 4, 2007 Place of residence: a few miles outside of the midst of nowhere Posts totaling 14,427 0 people have expressed an interest.

AMFR500 Member on 12/27/13 at 05:34 a.m.

The Escape is experiencing a variety of difficulties.

on December 27th, 2013 Ford Customer Service Representative Date of joining: October 25, 2010 Dearborn, Michigan is the location.

The original post was made by Lime05.

My father recently purchased a 2013 Ford Escape Titanium.

The automobile, on the other hand, resets itself every time you switch it off.

When I called the dealership, they told me that the light had to be turned on for them to do anything.

While the light was still on, he promptly drove it back to the dealership to get it fixed.

As a result, they accomplished nothing.

He travels a long distance for business and is unable to just leave every time to go back to the dealership in order to keep the light on.

It’s a spanking new automobile!

If you are able, Deysha, please raise this matter to the proper parties.

Due to the possibility of an air bag failure or malfunction, he is becoming increasingly apprehensive about operating the vehicle.

Lime05, thank you so much for the mention.

Deysha At 4:49 p.m.

Number of posts: 333 0 Likes have been received.

I considered going to another dealer, but it’s difficult because the light keeps coming back on as soon as the car is turned off.

Thank you for taking the time to respond and for being concerned about this problem.

on December 27th, 2013 Member of BullittJoined on November 16, 2011Location: Southeast Iowa 443 total posts If the airbag light is on, even in the event of an accident, the airbags will not deploy.

on December 28th, 2013, The Bullitt MemberThread StarterJoined on the 4th of July, 2012.

0 Likes 0 Dislikes 0 comments have been made.

That is the most significant concern.

Aside than that, it’s been a fantastic vehicle to drive.

I thought I read somewhere that your father was concerned about it accidently deploying.

And, of course, I have no recollection of it now.

And they can normally read history codes, so it sounds like some b.s.

And even if they are unable to determine what is causing it, they should preserve it and continue to investigate; otherwise, it seems that they are not attempting to do so.

Ford Customer Service Representative Date of joining: October 25, 2010 Dearborn, Michigan is the location.

The original post was made by Lime05.

Deysha has been assigned to the case!

Lime05, thank you so much for your kind words!

on February 14th Bullitt MemberThread Starter is a thread starter for Bullitt members.

0 Likes0 Comments0 Posts After all, the light has been turned back on.

The mechanic stated that he would connect it to the diagnostic computer at the back of the vehicle.

What is the purpose of the light being on then?

When you get close to the automobile, it is meant to automatically unlock the door for you.

In addition, the back door/tailgate door is meant to open and close on its own, although this only works partially of the time.

He is now considering simply selling it and trading it in.

The getaway did not go down well with me at all.

However, thus far, the escape has been a jumble of problems.

0 Likes0 Comments0 Posts To my ears, this seems like a software problem.

This is an unpleasant consequence of the increasing amount of electronics in automobiles nowadays.

on February 2, 2014 The Bullitt MemberThread StarterJoined on the 4th of July, 2012.

0 Likes0 Comments0 Posts As a result, we were able to get the automobile back.

So far, so good.

The light has not yet been turned back on.

Hopefully, that was the problem and it has been resolved.

It was beneficial to have the situation elevated.

7:00 a.m.

As a result, we were able to get the automobile back.

So far, so good.

The light has not yet been turned back on.

Hopefully, that was the problem and it has been resolved.

It was beneficial to have the situation elevated.

Lime05, you’re in good hands!

Topics that are related ThreadThread StarterForumRepliesThreadThread Starter The most recent postRando2010-2014 Mustang 98/25/2109:32 PM (Wednesday, April 25th) Vendor Showcase at carid 23:29:29 UTC on 30th of June, 2011.

parts for a lavaroach for sale 11/19/16 09:22 p.m. (EST) Modifications to the Cobiecane5.0L GT The time is 10/23/1509:44 a.m. exgto2012-2013 BOSS 30259/28/1508:39 PM exgto2012-2013 BOSS 30259/28/1508:39 PM

4 Reasons Why Your Airbag Warning Light is On

Airbag repair is not the most common type of car repair service, but it is required from time to time for a variety of reasons. In the event of an accident in which one or more of your airbags are deployed, it is obvious that they will need to be replaced, and the sensors will need to be reset. What happens, on the other hand, when you haven’t been in an accident but are still experiencing airbag problems? Airbag warning lights will illuminate or flash on your dashboard or computer display to alert you of the situation.

It implies that if you are involved in an accident, they will not deploy correctly.

There is always the possibility that the airbag light has been activated by mistake and that it just has to be reset.

The Airbag Backup Battery has been depleted.

In some cases, after the battery is completely charged again, the problem may resolve itself; in others, the backup battery will need to be recharged in conjunction with a sensor reset.

They communicate directly with the vehicle’s computer system, which allows them to identify and alert the driver of any possible problems.

The sensors will need to be verified, and the system will need to be reset before this can be done.

The purpose of the airbag clock spring is to ensure that the electrical wiring of the car and the driver-side airbag remain connected at all times.

It is possible for it to become worn out naturally over time, resulting in a weak connection and the possibility of airbag failure.

Module for wet airbags If your car has been subjected to water damage, it is possible that the airbag module, which is positioned under the driver and/or passenger seat, has been harmed.

Your airbag warning light is illuminated for a purpose, whether it is activated by accident or as a result of one of the common causes listed above.

Why bother using airbags if they aren’t going to deploy in the event of an accident? Call San Francisco Automotive Solutions now at (415) 957-1170 or use the online scheduling tool to arrange an appointment for all of your airbag repair and diagnostic needs.

Leave a Comment

Your email address will not be published. Required fields are marked *