Wipers won’t shut off?

Faulty park switch: Inside the wiper motor is a park switch. Bad wiring: A loose wire or bad connection could also cause your windshield wipers to continue to run even when they are turned off. A mechanic with the proper diagnostic tools can easily check the wiring and locate any issues.

  • As you rotate the knob to activate the wipers, the resistance changes and the Wiper Control Module (WCM) reads the changing voltage and commands the wipers to a new speed or on/off. When wiper won’t shut off the problem is due to a poorly designed multi-function switch, not a bad WCM or a defective Generic Electronic Module (GEM).

What would cause windshield wipers to not turn off?

Why Wiper Blades Won’t Turn Off Faulty Relay: Every windshield wiper system has an internal electric switch mechanism called a relay. Faulty Park Switch: When the park switch fails, the system no longer tells the wipers to stop at the bottom of the windshield, and they often won’t stop at all.

How do you reset the windshield wipers?

Your wipers may need resetting due to loosening up over time, or being forced out of position when an abnormal amount of stress was placed on the wipers, such as clearing large chunks of ice. Resetting the wipers involves removing the wiper linkage and manually placing the blades in the right position.

Why are my windshield wipers stuck on?

Generally, when windshield wipers get stuck in the upright position it’s because of a small metal tab that the wiper transmission is supposed to catch on gets bent out of place. You can access the wiper transmission by pulling off the foam strip and plastic cover that sits below your windshield.

How do you know if your windshield wiper switch is bad?

Common signs include windshield wipers not turning on or off, not changing speed or settings, and the turn signals not working.

Where is the wiper relay?

In some vehicles, the wiper relay switch is inside the actual windshield wiper motor. If it fails, the entire motor needs to be replaced, as you can’t get parts to fix it.

How much does it cost to fix a windshield wiper motor?

You will pay between $230 and $310 for a windshield wiper motor replacement. The cost of labor on this job will be between $50 and $70, while the cost of parts should be between $180 and $250.

What is the windshield wiper switch called?

It is variously called the combination switch, the dip beam switch, or the directional/wiper switch. The left hand stalk signals and cancels turn indications when moved up or down.

Why do my windshield wipers turn on when I start my car?

Most of the time this is caused by a hardware failure in either the steering control module or the integrated power control module. Most of the time this is caused by a hardware failure in either the steering control module or the integrated power control module.

Why Won’t My Windshield Wipers Turn Off?

If you are not a vehicle enthusiast, you may be surprised to learn how complicated today’s autos have become. This is true even for windshield wiper systems, which might fail for a variety of reasons. One of the most worrisome and unexpected problems is when the windshield wipers continue to wipe even while the vehicle is not in motion. It is conceivable that your wipers will not turn off, no matter what position the wiper switch control is in. There are a few probable explanations for this problem.

How the Wiper System Works

Modern vehicles may be quite sophisticated, which may be overlooked by those who are not automotive enthusiasts. This is true even for windshield wiper systems, which might fail for a variety of reasons. A particularly scary and unexpected occurrence is when the windshield wipers continue to wipe even when the vehicle is shut off. It is conceivable that your wipers will not turn off, no matter what position the wiper switch control is in. There are a few probable explanations for this condition.

Why Wiper Blades Won’t Turn Off

If your wipers continue to operate even after you have turned them off, it is most likely due to one of the three issues listed below. Because the only method to determine where the problem originates is by trial and error replacement of parts, you might as well start with the simplest solution first: The failure of a relay: Every windshield wiper system is equipped with an internal electric switch mechanism known as a relay. Typically, auto-motive relays are tiny, plastic boxes that connect into a specific spot on an under-hood covered panel, along with a handful of other relays.

  1. Changing the wiper relay is the quickest and most straightforward solution, and it may also be the most effective.
  2. Failure of the Wiper Switch: The wiper switch is the switch that is actuated when you turn the wipers on and off, and it contains a large amount of intricate internal circuitry.
  3. It will be more difficult to replace the switch than it will be to replace the relay since you will have to disassemble a portion of the steering column.
  4. Park Switch Failure: When the park switch fails, the system no longer instructs the wipers to stop at the bottom of the windshield, and they frequently fail to stop at all.

Faulty Park Switch: Many systems have park switches integrated straight into the wiper motors, which means that the wiper motor must be changed as a complete in this situation.

How to Fix Wipers That Won’t Turn Off

Repairing wipers that won’t turn off nearly often entails replacing the component that is causing the problem. Fortunately, it’s rather simple to locate new components on the internet. So, after you’ve figured out why your windshield wipers aren’t turning off, you’ll know just what to get for them. The task of replacing the item is frequently straightforward enough to be completed at home; however, if you are uncomfortable pulling parts out of your automobile or are unsure of the nature of the problem, consider taking your vehicle to a technician.

What to Do When Your Windshield Wipers Won’t Turn Off ❤️

Windshield wipers are among of the most crucial safety components on your car, despite the fact that the majority of drivers don’t give them much thought. Even when they’re operating correctly, we don’t pay much attention to them. However, if your wipers aren’t working properly and you’re driving in terrible weather, it might be practically hard to drive your car since the visibility will be so poor. No matter if it’s heavy rain or snow, if your windshield wipers aren’t operating properly, it’s going to be extremely unsafe for you and other drivers on the road to be behind the wheel.

Automobile repairs are EXTREMELY EXPENSIVE.

Let’s have a look at what may be going on in your car that would prohibit you from being able to switch off your wipers and what you can do to get them back to operating correctly.

How Come My Windshield Wipers Won’t Turn Off?

Windshield wipers are among of the most crucial safety components in your car, despite the fact that the majority of drivers don’t give them much thought. Even when they’re operating correctly, we don’t pay much attention to them. However, if your wipers aren’t working properly and you’re driving in terrible weather, it may be practically difficult to operate your car since the visibility would be so poor. No matter if it’s heavy rain or snow, if your windshield wipers aren’t operating properly, it’s going to be extremely unsafe for you and other drivers on the road to be on the road.

In some circumstances, your windshield wipers will not come on at all, and in others, they will not switch off at all.

To attempt to travel in this direction while unable to switch off your windscreen wipers will undoubtedly be a source of irritation.

How Do I Fix Windshield Wipers That Won’t Turn Off?

Of course, determining how to fix wipers that won’t turn off requires first determining why they won’t turn off in the first place. We’ve noticed that there are generally just a number of reasons why your wipers won’t switch off, which means you only have a few viable things to look at in terms of resolving the issue. The cost of a windshield wiper switch replacement is likely to range between $200 and around $250, depending on the severity of the problem you’re experiencing. It is possible that you may be charged between $100 and $250 to have your windshield wipers fixed if you have a problem with the wiring in your wipers and need to replace the linkage.

Finally, if the problem is connected to the motor itself, you may purchase a windshield wiper replacement motor for as little as $25 for an aftermarket replacement to as much as $400 for a genuine OEM replacement motor.

Can You Turn Off Rain Sensing Wipers?

The ability to switch on a rain detecting system in some cars, which causes your wipers to run when it is raining without you having to manually engage them, is available in some models. However, this technology does not always function in the manner in which you would expect it to. Some automobiles’ windshield wipers will not turn on even while it is raining, and others may turn on even when it is not raining at all, depending on the manufacturer. Both of these situations may be inconvenient, and dealing with wipers that aren’t working when you need them can be potentially hazardous.

You can just press the stalk up into the on position, just like you would with any other type of conventional wipers, when you need them all again to function properly again.

See also:  P0455, P0456 Acura?

It would be quite rare for your wipers to continue to operate even after you had pulled the stalk control all the way down to the off position unless, as we have already discussed, the park switch has ceased to function.

Why Won’t My Windshield Wipers Work?

It goes without saying that your windshield wipers not shutting off is a major nuisance. However, if your windshield wipers refuse to operate in inclement weather, this is a far more serious problem. If you’re traveling in poor visibility circumstances, you’ll want to ensure sure your windshield wipers are in good working order. If you are attempting to drive without them, it is exceedingly unsafe. Wiper Blades that are damaged: If this is the cause of your problem, it is probable that your wipers will operate normally, but they will be unable to do their task effectively.

  1. The rubber edges function similarly to squeegees, pushing the water away from your range of vision as you walk.
  2. The greater the size of the tears or holes, the greater the difficulty you’ll have when you try to wipe your windshield clean and realize that the blade is simply unable to complete the task at hand.
  3. In contrast to a malfunctioning park switch, which can enable your blades to continue to operate long after you turn them off, the motor itself may fail in such a manner that the blades are unable to turn on at all.
  4. According to the information we provided previously, obtaining a replacement windshield wiper motor may not be too expensive.
  5. During the winter, as snow and ice accumulate around your windshield wipers, they might become stuck to the hood of your vehicle.
  6. Lift the blades and give them a good tap to make sure they’re free and clear of any ice that may be preventing them from moving freely.
  7. Pivot Nut Failure: The arms to which your windshield wiper blades are attached are connected to the windshield wiper assembly by means of a piece of hardware known as a pivot nut.

Over time, these nuts can become loose, causing your wiper motor to begin spinning the pivot itself, but the arm will remain stationary due to the fact that they are no longer firmly linked to one another.

If that’s the case, the pivot nut is most likely the source of your frustration.

When this occurs, it is also conceivable that one wiper will function well while the other would not.

This fuse is bad.

It should not be necessary to spend a lot of money to replace a fuse; you may be able to get a replacement fuse for less than $5.

Before you put that new fuse in, give the motor a thorough check to determine if there is any type of short or other problem related with it so that you can avoid the problem from occurring again.

The Bottom Line

Wrinkle-free windshield wipers are rather inexpensive; you can pick them up for a few dollars at your local Walmart, as well as any other store that sells vehicle supplies and even petrol stations. Therefore, we don’t treat them with much regard because they’re so simple to come by and because the majority of us can replace them without having to visit a technician for help placing them back in their proper location. While windshield wipers are inexpensive and simple to operate, we must not lose sight of the fact that they are vital to maintaining a safe driving environment during inclement weather.

When your wipers are not operating correctly, your visibility will be substantially reduced, and the likelihood of being involved in an accident will be exceedingly high.

Always keep in mind that it is not only your own safety on the road that you must consider, but the safety of everyone else as well, and you cannot put yourself and others in danger over something as minor and easily rectified as a problem with your wiper blades not responding the way you want them to.

General Questions – Windshield wipers won’t shut off

In response to Laura’s question on April 14, 2018 at 12:26 PM General in nature is the question type. When the automobile is operating, the windshield wipers remain on high and will not turn off.

10 Answers

Laura provided a solution 3 years ago. If your wipers aren’t turning off, the problem might be with the relay. This was deemed to be helpful by 59 people. Laura provided a solution 3 years ago. The wipers will not turn off25 people found this article helpful. Jorge provided a response 3 years ago. Check the connection between the ground and the power source. It’s possible that the wiper switch or motor is faulty. This was reported to be helpful by 7 people. Laura provided a solution 3 years ago.

  • This was deemed to be helpful by 5 people.
  • The windshield wiper motor has been in service for two months.
  • When I’m driving, my wipers turn on and the engine comes to a complete stop.
  • Please assist me.
  • This was reported to be helpful by 6 people.
  • I had to disconnect it since it would not turn off on its own.
  • Disconnect the connector for the washer fluid.
  • The motor for the washer fluid is not working properly.
  • The problem with the wipers not shutting off happened shortly after the ‘Low PowerFluid’ sign on the dashboard was shown.
  • I’ve only used the fluid on a few occasions.
  • Aches and pains in the A.

I wish I hadn’t handed my 2008 to my kid in the first place. This was beneficial to 1 person. When I’m traveling down the road in my 2011 Ford Escape 4 cylinder, the windshield wipers will turn on at a sluggish speed and water will flow out around every 5 minutes or so. What is the problem?

Related Questions

  • Windshield wipers remain on high speed while the vehicle is moving and will not turn offGeneral

Alarm won’t shut off17 Answers

  • I accidently washed my keyless entry after leaving the doors open while cleaning the interior (which most likely caused thebattery to drain). The alarm went off on its own and couldn’t be turned back on. The following information applies to the 2002 Dodge Stratus R/T Coupe FWD:

Truck won’t shut off2 Answers

  • When the truck begins, it won’t stop. It is necessary to unplug the battery. Once the battery is reconnected, the machine begins to operate. Dodge Dakota-General
  • Dodge Dakota-General

2001 Chevy Silverado 1500, Windshield Wipers won’t shut off 1 Answer

  • Why am I unable to switch off the windshield wipers on my 2001 Chevrolet Silverado? Maintenance and repair of a 1999 Chevrolet C/K 1500

windshield wipers won’t turn off.2 Answers

  • I have a 1979 Corvette with wipers that would not turn off. I removed them from the wiper motor’s power supply. Do you think the issue is related to the wiper switch in the car? Repair and maintenance of a 1979 Chevrolet Corvette
Share your experience with others.

Constructed content posted by Users does not represent the thoughts of CarGurus and should not be deemed to have undergone any form of review, vetting, or approval by CarGurus. Please refer to the CarGurusTerms of Service for further information. If CarGurus becomes aware that any content is in violation of our policies, it will be deleted.

Why are my windshield wipers not turning off?

Asked in the following category: General The most recent update was made on June 13th, 2020. Park switch that isn’t working properly: A park switch is located within the wiper motor. If this switch fails, an electric current will continue to flow through your windshield wiper system even when the system is switched off. In addition, a loose wire or a faulty connection may result in your windshield wipers continuing to operate even after they are switched off. Remove the wiper fuse from the fuse box or the battery wires, whichever is first.

The switch has been stuck in the on position and will not move.

It is also possible to wonder, ‘How can I tell if my windshield wiper motor is bad?’ A malfunctioning windshield wiper motor can be identified by the following signs:

  1. The wipers are completely immobile
  2. The wipers function at a slower rate than they would usually. The wipers are only capable of operating at a single speed. The wipers are acting strangely
  3. The wipers do not come to a complete halt at their prescribed location, nor do they come to a complete stop without returning to their starting position.

Nothing moves on the wipers; they are completely immobile. Compared to typical, the wipers are operating at a slower rate. One speed is available for the wipers; there are no other options. Anomaly in the operation of the wipers Neither the wipers nor the wiper blades come to a complete halt at their specified location or without returning to the appropriate’resting’ area.

  1. Unscrew the plastic cover that is sandwiched between the hood and windshield and covers the wiper motors and arms
  2. To remove the nut situated in the center of the wiper motor, use a socket wrench to turn it counterclockwise.

Is there a fuse for the wipers on the windshield? Your wipermotor electrical circuit is protected by a fuse, which will blow if the motor is overloaded, preventing the motor from overheating. When the fuse blows, the power will be stopped, and the wiper system will be shut down. Solution: Consult your owner’s handbook to find out where your fuses are located and which fuse protects the wipermotor.

His windshield wipers refuse to stop wiping, even when switched off

DEAR CAR TALK: DEAR CAR TALK: My 2006 Chrysler TownCountry has an unusual problem with the transmission. I was driving in the rain with my wipers on on a few weeks ago. When I pulled into a parking spot and shut off the car, the wipers continued to operate. The ignition was turned off, which led me to believe that I had the key in accessory mode. I then started and stopped the car many times, and the wipers continued to operate. After then, I removed the key from the ignition. The wipers continued to operate.

  • The moment I replace the fuse, they immediately restart, even if the car is not in motion and the key is in my palm.
  • Changing the setting on the wipers will cause them to move from regular to fast, however they will not perform in the intermittent mode.
  • Thanks.
  • I’m thinking about a few of possibilities.
  • That can be found in the fuse box, which is well labeled!
  • Try switching the positions of the two relays.
  • My second guess, if swapping the relays doesn’t make a difference, is that the wiper motor is malfunctioning.
See also:  P1506 Ford high idle speed?

The motor for the windshield wipers is right up against the firewall of the vehicle.

It actually just plugs into a socket on the firewall, which is all that is required.

To be more accurate, you’ll want to find an automotive recycling center (also known as a junkyard) and purchase a used windshield-wiper motor for $20 or $30.

Simply plug it in and test the wiper switch to see if the new motor comes to a complete stop when the wiper switch is turned off.

If it isn’t the relay or the motor, you’re getting close to poltergeist territory, Mr.

The use of a real mechanic as well as wiring diagrams and voltmeters, as well as possibly a couple of hemlock roots and an eye of newt, may be required.

Do you have a question about automobiles?

There is an error with the username and password. Please check your email to ensure that your registration has been confirmed and completed. To reset your password, please complete the form below. After you’ve submitted your account email, we’ll send you an email with a code to reset your password.

Windshield wipers won’t turn off HELP!

A similar problem with the car not shutting off intermittently occurred, and when I took it to the dealer, he determined that the problem was a bad ground, which he tightened, and then the problem reappeared, after which the mech said, ‘I’ll get my boss,’ and then another mech raised a nearby lift and crushed the right rear door on my brand new car because the first mech had parked it in an improper position in our stall.

  • Soon after, I discovered that if you shut off the wipers as they were reaching the park position, the wipers would turn off properly.
  • We were never able to determine the fundamental cause and remedy the problem.
  • It’s a combination of two functions.
  • It’s a function with the OR operator.
  • Again, the question is, ‘Which one or many inputs are causing the difficulty?’ I suppose you could wire a switch in series with this park position switch and manually switch it off when the wipers won’t turn off while the car is in park.
  • If you fiddle with the wiper mechanism, be careful not to break your fingers.

Wipers won’t shut off F150

Ford has released a service bulletin15-006 to address a problem with the wipers not shutting off on theBL3Z-13K359BA multifunction switch cars mentioned below that has been identified. The multi-function switch on the steering column, or the wiper motor, must be replaced in order to correct the problem. But first, be certain that yours exhibits these indications. The technical service bulletin15-006 addresses a problem where the wipers will not turn off even after you have turned the wiper switch to the off position.

Read more

Vehicles affected by TSB15-006

Ford Edge (2011-2014 model years) Ford Explorer (model years 2011-2014) Ford F-150 and F-Super Duty pickup trucks from 2011 to 2014. Lincoln MKX (2011-2014 model years)

How Ford wipers work

A situation like this would almost certainly imply a shorted wiper switch, as in the olden days the wiper switch actually transferred power to the wiper motor itself. However, nothing is as simple as it used to be. The multifunction switch seen in late-model automobiles serves as a signal to some form of controller, according to the manufacturer. In automobiles from the early 2000s, the switch signaled the body control module, which then switched on the electricity.

Ford vehicles from the last few years, however, have seen a shift. With the multifunction switch in this position, it serves as a signal to the Steering Column Control Module (SCCM). Yes, there’s still another PC.

Diagnose wipers won’t shut off issue

This type of problem in the past would be indicative of a shorted wiper switch, which would be indicated by a problem with the wiper switch itself. No longer, however, is anything as simple as it once was In late-model automobiles, the multifunction switch serves as a signal to some form of controller. Early 2000s automobiles used a switch to send a signal to the body control module, which in turn switched on the ignition. Ford vehicles from the recent past, however, have undergone changes. With the multifunction switch in this position, it operates as a signal to the Steering Column Control Module (SCCM).

Replace multifunction switch Ford F150

To reach the multifunction switch, you must first remove the airbag, steering wheel, and clockspring from the vehicle. The steps are as follows: Turn off ALL of your devices. Turn the ignition switch to the ‘OFF’ position to turn off the vehicle. The body control module (BCM) is located underneath the right-hand side of the instrument panel of the vehicle. After that, disconnect the RCM fuse from the BCM. In order to start the vehicle, turn the ignition switch to ‘ON.’ The airbag light should remain illuminated for a minimum of 30 seconds after activation.

  • If it starts to flash or go out, you’ve removed the incorrect fuse.
  • Disconnect the negative battery cable and wait for the airbag system to shut down for at least one minute after doing so.
  • Remove the steering wheel from the vehicle.
  • Replace the multifunction switch and replace all of the components in the reverse sequence in which they were originally installed.
  • Reconnect the negative battery connection to the rest of the battery.
  • Wait for a total of ten seconds.
  • The airbag light should be illuminated for about 6 seconds before turning off completely.
  • If there is an issue, the airbag light will remain illuminated, will not light, or will flash continuously.

Ford multifunction switch part numbers

On or after May 17th, 2011, the BC3Z-13K359BA Switch Assembly for the Ford F-Super Duty (2011-2013) was available in black. On or after October 28th, 2013, the switch assembly was available in black. The 2011/2013 model year has a smaller camera and a variable intermittent windshield wipe. From: May 17th, 2011 to: October 28th, 2013 2011, 2012, and 2013 models include a fixed rear view camera and variable intermittent windshield wipers. Make the purchase of a new BC3Z13K359BA multifunction switch.

It is also equipped with Rain Sensitive Windshield Wipers.

CL3Z-13K359AA Switch Assembly – F150 – Black, From: 10/24/2011 To: 10/28/2013 2012/2013; Front Camera/Rear View Camera, With Variable Int.

Windshield WipeEL3Z-13K359AA Switch Assembly – F150 – Black, From: 10/28/2013 To: 12/23/2014 2014/; Less Camera, With Variable Int. Windshield WipeEC3Z-13K359 Rick Muscoplat is a professional musician. Rick Muscoplat posted a blog entry on

Windshield wipers won’t shut off

This discussion is proudly sponsored by:
Please support our sponsors and let them know you heard about their products on iRV2
04-03-2019, 01:18 PM 1
Senior MemberRetired Fire Service RVer’sJoin Date: Aug 2014Posts: 105 Windshield wipers won’t shut off


Hi, I have a 06 class a Holiday Rambler and the windshield wipers won’t shut off without pulling the fuse. The wiper switch on the column has the blinkers and the cruise control also. Does anyone know what the problem might be?

Join the1 RV Forum Today – It’s Totally Free!iRV2.com RV Community -Are you about to start a new improvement on your RV or need some help with some maintenance? Do you need advice on what products to buy? Or maybe you can give others some advice? No matter where you fit in you’ll find that iRV2 is a great community to join. Best of all it’s totally FREE!You are currently viewing our boards as a guest so you have limited access to our community. Please take the time to register and you will gain a lot of great new features including; the ability to participate in discussions, network with other RV owners,see fewer ads, upload photographs, create an RV blog, send private messages and so much, much more!
04-03-2019, 01:33 PM 2
Senior MemberJoin Date: Aug 2012Location: WI 54016Posts: 294 If they are like a cars then when you turn the wiper control off the motor still has power going to it but it’s supposed to ‘park’ and then shut off. Sounds like the park switch inside the motor has failed and is allowing the wipers to just continually run.Do they start back up when you put the fuse back in or do you need to actually turn them on with the wiper control switch?._2007 Fleetwood Providence 39VAllison 3000MH 7.5 Onan
04-03-2019, 02:30 PM 3
Senior MemberJoin Date: Jun 2006Location: Dallas,ORPosts: 4,584 That was a real common problem in the 80s with GM cars. Usually the park switch failure. It can be caused by moisture. Replace the motor is the usual remidy._Don and Lorri Resident Dummy.
04-04-2019, 05:47 AM 4
Senior MemberRetired Fire Service RVer’sJoin Date: Aug 2014Posts: 105 Yes the wipers run when I put the fuse back in without touching the switch. Is there any test I could do to make sure it’s the motor?
04-04-2019, 01:13 PM 5
Senior MemberJoin Date: Oct 2002Location: Madison, MSPosts: 9,838 Quote:Originally Posted bymantYes the wipers run when I put the fuse back in without touching the switch. Is there any test I could do to make sure it’s the motor?ASSUMING you have a front engine gasser HR, look under the hood and disconnect the plug in the wiring harness to the wiper motor. use some contact cleaner and dry it out completely. Likely you have some moisture in there shorting out to run continously. Once dry, plug it back together and wrap completely in plenty of electrical tape to prevent water getting back into it.
04-04-2019, 04:33 PM 6
Senior MemberRetired Fire Service RVer’sJoin Date: Aug 2014Posts: 105 Thanks I will try that, that would be the easiest fix on this rig so far!
04-04-2019, 07:15 PM 7
Senior MemberOutdoors RV Owners ClubJoin Date: Oct 2014Posts: 3,532 I had a the switch burn out once. Had to replace the whole turn signal stalk._2020 F28 RKS Titanium 2017 Creekside 23 RBS Sold 2016 F250 Super Crew XLT Overworked
04-05-2019, 06:30 AM 8
Senior MemberRetired Fire Service RVer’sJoin Date: Aug 2014Posts: 105 I’m really hoping it’s not the stalk, cleaning or a new motor would be a much easier fix
04-05-2019, 09:36 AM 9
Senior MemberJoin Date: Dec 2014Posts: 281 I had that problem on my Winnebago. It has the Workhorse chassis. I see that Holiday Admirals also came with the Workhorse chassis. So�.There are several fixes floating around this forum:1. Seal the wiper motor connector. This is the connector near the wiper motor located top center under the front hood. I tried this with some success.2. Seal the top of the front hood with a weather strip (hollow rubber door strip). The idea was to keep the rain water from getting to the connector/motor. I didn�t try this because the next method worked for me.3. Use cable ties to tie up the wiper motor connector as far up away from the hood opening as possible.This worked for me._’06 Winnebago Voyage 33′, W20, 8.1L
04-05-2019, 01:30 PM 10
Senior MemberRetired Fire Service RVer’sJoin Date: Aug 2014Posts: 105 So it wasn’t the connection, took it apart and cleaned it up, no difference. Took the motor out hoping to get it bench tested but the auto electric shop needs it in the vehicle to troubleshoot it. I think I would like to bypass the stalk switch and see if it shuts off the way it suppose to. Anyone know how I could do that, it has 5 wires going to it?
04-05-2019, 05:01 PM 11
153starsSenior MemberJoin Date: Mar 2019Location: Braidwood Il.Posts: 4,350
04-06-2019, 07:36 AM 12
Senior MemberRetired Fire Service RVer’sJoin Date: Aug 2014Posts: 105 That was a cool video, I took the cover off mine and it had a lot of grease in there, don’t know if it belonged in there or not but cleaned it up, maybe that will help
04-06-2019, 03:06 PM 13
Senior MemberRetired Fire Service RVer’sJoin Date: Aug 2014Posts: 105 So I took the motor out and checked the wires going to the motor with a volt meter, found the hot wire and checked all other 5 wires and there was power going to all the others at the appropriate times with the switch going from high, low, intermittent and off. So by all that I would say the motor is bad. Thanks for all the help!
04-06-2019, 08:55 PM 14
Senior MemberJoin Date: Aug 2012Location: WI 54016Posts: 294 There should be some grease to lube the nylon gear teeth as they make contact with the metal scrolling gear. If I’m replacing the pump I’ll usually clean out the old dried up white lithium the factory used and replace it with some Mobil 1 wheel bearing grease. Good for life of the motor._2007 Fleetwood Providence 39VAllison 3000MH 7.5 Onan
Currently Active Users Viewing This Thread: 1(0 members and 1 guests)
Posting Rules
Youmay notpost new threadsYoumay notpost repliesYoumay notpost attachmentsYoumay notedit your posts


BB codeisOn SmiliesareOn code isOnHTML code isOffTrackbacksareOff PingbacksareOff RefbacksareOff


Forum Rules

Similar Threads
Thread Thread Starter Forum Replies Last Post
Windshield Wipers wont shut off bassoneman Thor Industries Owner’s Forum 2 03-31-201907:46 PM
Windshield wipers – link for finding proper wipers WriteOn Gear and Product Discussions 6 07-30-201812:39 PM
Wipers won’t shut off gregoryd73 Winnebago Industries Owner’s Forum 17 07-25-201806:38 AM
Ford windshield wipers won’t turn OFF Goldwingit Ford Motorhome Chassis Forum 8 04-11-201507:41 PM
Wipers would not shut off cef2lion Workhorse and Chevrolet Chassis Motorhome Forum 33 12-20-201010:20 PM

wipers won’t shut off

07:14 a.m. on June 28th, 2013. Initiator of a thread, Junior MemberJoined on June 13, 2013 Posts: 5Likes: 0Received 0 Likeson0 Postswipers won’t turn off after being turned off When I try to turn off the wipers on my 2005 GMC Sierra, they just won’t turn off! The delayed function was activated while I was using it, then it suddenly switched to a continuous slow pace. I attempted to turn them off, but to no effect. They are capable of reaching great speeds, yet they refuse to turn off. Any feedback on this would be much appreciated.

  • on June 28th, 2013 Senior Member and self-proclaimed ‘Car Nut’ Wiper motors, for the most part, are equipped with a series of points inside that allow the motor to ‘park,’ ie to turn off when the blades are in their parked position.
  • Check to check that the wiper arms do not have any obstructions to their complete range of motion.
  • Whether required, thoroughly clean the affected area to determine if this will resolve the issue.
  • The date and time now is June 28th, 1:27 PM.
  • Wiper motors, for the most part, are equipped with a series of points inside that allow the motor to ‘park,’ ie to turn off when the blades are in their parked position.
  • Check to check that the wiper arms do not have any obstructions to their complete range of motion.
  • Whether required, thoroughly clean the affected area to determine if this will resolve the issue.

Thank you for the information.

The time is 1:49 p.m.

Senior Member and self-proclaimed ‘Car Nut’ The points that detect the park position might fail on an intermittent basis.

In the interim, find the wiper fuse (if you haven’t previously done so) in case you need to yank it to turn off the wipers.

Date of joining: June 2013 Number of posts: 5 No likes have been received, and no likes have been given on any of the posts.

I’m from New Hampshire, and all we’ve been receiving lately has been rain, rain, and more rain.

Once again, thank you so much.

Senior Member and self-proclaimed ‘Car Nut’ Use the wiper washer squirter and then immediately turn it off to see if it helps.

Suspension for a 1997 Buick Park Avenue (Soft Ride)!

ZCRX871992-1999307-18-200602:50 AMM ZCRX871992-1999307-18-200602:50 AMM ZCRX871992-1999307-18-200602:50 AMM ZCRX871992-1999307-18-200602:50 AMM ZCRX871992-1999307-18-200602:50 AMM ZCRX871992-1999307-18-200602:50 AMM ZCRX871992-1999307-18- BeanBuick511-03-200509:25 p.m.

r BeanBuick511-03-200509:25 p.m. gowilly201992-1999401-22-200401:34 AM gowilly201992-1999401-22-200401:34 AM davidmprice1992-1999901-10-200305:43 PM davidmprice1992-1999901-10-200305:43 PM davidmprice1992-1999901-10-200305:43 PM davidmprice1992-1999901-10-200305:43 PM

Wipers won’t shut off.

07:14 a.m. on June 28th, 2013: Date of joining: June 2013 Junior MemberThread Starter 0 Likes have been received 0 Likeson0 Postswipers will not turn off. 0 Likes have been received 0 Likeson0 When I try to turn off the wipers on my 2005 GMC Sierra, they simply won’t turn off. The delayed function was activated while I was using it, then it suddenly changed to a continuous slow pace. They remained turned on despite my best efforts. However, they will accelerate to a high rate of speed but will not decelerate.

Thanks, Bert 07:35 a.m.

If these points are unable to be ‘tripped,’ the motor will continue to operate as usual.

Occasionally, leaves, twigs, and other debris might become caught below the windshield line and obstruct the wiper arms’ ability to function properly.

Some stuck points can be jarred loose by a vigorous tap on the motor with a rubber mallet; however, if this does not stop the motor from running, the remedy is only temporary, and the motor will need to be rebuilt or replaced.

on Friday, June 28th Junior MemberThread StarterJoined: Jun 2013Posts: 5Likes: 0Received: 0 Likeson: 0 2kg4u originally posted 0 posts in this thread.

If these points are unable to be ‘tripped,’ the motor will continue to operate as usual.

Occasionally, leaves, twigs, and other debris might become caught below the windshield line and obstruct the wiper arms’ ability to function properly.

Some stuck points can be jarred loose by a vigorous tap on the motor with a rubber mallet; however, if this does not stop the motor from running, the remedy is only temporary, and the motor will need to be rebuilt or replaced.

It appears that the problem has been resolved once I stepped outside and restarted the truck?

Depending on how often it happens, you may need to replace the wiper motor altogether.

Friday, June 28th, 2013 at 2:09 PM Initiator of a discussion thread Beginning in June of 2013, you’ll be able to 5 people have commented.

Thank you; I’m already aware of where the fuse is located!

Every time it rains, Bitch gets out of his car and removes the fuse.

on June 28, 2013 True Car Nut, Senior Member Use the wiper washer squirter and then immediately turn the vehicle off, if that works.

Suspension on a 1997 Buick Park Avenue (Soft Ride)!

on the 23rd of October, 1992-1999 On the 18th of July, 2006, at 02:50 AMM, ZCRX871992-1999307 was assigned to the ZCRX871992-1999307-18-2006ZCRX871992-1999307-18-2006ZCRX871992-1999307-18-2006ZCRX871992-1999307-18-2006ZCRX871992-1999307-18-2006ZCRX871992-1999307-18-2006ZCRX871992-1999307-18-2006 The time now is 9:25 p.m.

r BeanBuick511-03-200509:25 p.m. on November 3, 2005. I am gowilly201992-1999401-22-200401:34 AM on the 22nd of April in the year 1999. 01/10/2003 05:43 PM davidmprice1992-1999901-10/2003 05:43 PM davidmprice1992-1999901-10/200305:43 PM davidmprice1992-1999901-10/200305:43 PM davidmprice1992-19999

Leave a Comment

Your email address will not be published. Required fields are marked *