2009 Ford Edge Sensor Locations? (Question)

Front Impact Sensor (Left) (Edge) Left front of engine compartment. Front Impact Sensor (Left) (MKX) Left front of engine compartment. Front Impact Sensor (Right) (Edge) Right front of engine compartment. Front Impact Sensor (Right) (MKX) Right front of engine compartment.

How many oxygen sensors does a Ford Edge have?

Oxygen sensors are located before and after the catalytic converter. A vehicle may have two to five oxygen sensors, and sometimes even more.

Where is the O2 sensor located on a Ford Edge?

There are four O2 sensors on Your 2011 Ford Edge: one on each side just below the exhaust manifold, and one on each side behind the second catalytic converters (which themselves are somewhat aligned to the back of the front doors).

Where is the crankshaft position sensor on a 2008 Ford Edge?

Crankshaft Position Sensor Lower left rear of engine.

Where are my O2 sensors located?

The Oxygen O2 sensor is located in your vehicle’s exhaust system, usually on the exhaust manifold or close to the engine. There may be several oxygen sensors on your vehicle. These sensors are always located in the exhaust gas flow of your vehicle.

Where is the O2 sensor on a 2009 Ford Escape?

Oxygen sensors are located within the exhaust stream, there is at least one oxygen sensor located before the catalytic converter and typically one in each exhaust manifold.

What side is bank 2 sensor 1?

Bank 2 Sensor 1 is the first sensor closest to the engine. On Bank 2 means it is at the engine side with cylinders 2, 4, 6, 8, etc. Bank 2 Sensor 2 is the second sensor on the engine’s exhaust pipe, usually behind the catalytic converter. On Bank 2 means it is at the engine side with cylinders 2, 4, 6, 8, etc.

Is bank 2 sensor 1 upstream or downstream?

Bank 2 Sensor 1 means Upstream Left/Front; Bank 1 Sensor 2 means Downstream Right/Rear; Bank 2 Sensor 2 means Downstream Left/Front.

Where is the crankshaft sensor on a 2010 Ford Edge?

The crankshaft position sensor is located near the engine’s crankshaft, and relays information about the crankshaft’s position as it rotates.

What happens when the camshaft sensor goes bad?

Poor Drivability A failing camshaft position sensor begins losing its ability to quickly transfer data. Mismatched fuel delivery and ignition timing, even if off by a few milliseconds, will cause your vehicle to sputter, accelerate poorly, lack power, stall or even shut off.

Where is the crank sensor on a 2007 Ford Edge?

The crankshaft position sensor on a Ford V6 is located on the driver side front of the motor, near the timing cover.

Where is the camshaft position sensor located?

Camshaft Sensor Locations The camshaft sensor is usually located near the top of the engine. It might be on the top of the block, on one or both heads, or on the intake manifold, usually near the timing cover. In some cases, you might find the camshaft sensor behind the timing cover.

How do I fix code P0012?

What repairs can fix the P0012 code?

  1. Resetting the fault codes and performing a road test.
  2. Changing the oil and filter to the proper oil viscosity for the engine’s specifications.
  3. Repairing or replacing the wiring or connection to the camshaft oil control solenoid.

What does P0016 mean?

P0016 is the OBD-II generic code indicating that the camshaft position sensor for bank 1 does not correlate to the signal from the crankshaft position sensor.

2009 Ford Edge Module Locations

The majority of Ford Module devices may be rebuilt and fullyFord body control moduleprogrammed by a qualified Ford Module rebuilding company. The fact that a control module must be programmed to your specific VIN makes purchasing a junk yard module preferable to purchasing a rebuilt one a no-brainer. Simply do a search for a rebuilder in your area and get in touch with them to inquire about cost and programming capabilities.

Find lots of other information for your Ford Vehicle.To find fuse diagrams,click hereTo find Relay locations,click hereTo find Sensor Locations,click hereTo find Module Locations,click hereTo find Switch Locations,click hereTo find Firing Order,click here

The ABS Control Module (Edge) is located on the left rear of the engine compartment. The ABS Control Module (MKX) is located on the left rear of the engine compartment. Module for all-wheel drive (AWD). Kick panel on the right. Antenna Module is a kind of antenna. Kick panel on the right. Under the driver’s seat is the Climate Controlled Seat Backrest Module (Driver’s Side). Module for the Climate Controlled Seat Backrest (Passenger Side) is located under the front passenger’s seat. Under the driver’s seat is the Climate Controlled Seat Cushion Module (Driver Side).

Temperature-Controlled Seat Module (Passenger Side) Located under the front-passenger seat.

  1. The cooling fan module (MKX) is located on the left front of the engine compartment.
  2. The Electronic Automatic Temperature Control (EATC) Module is located in the center of the dashboard.
  3. Motor for the blower.
  4. Heated Seat Module (Left Rear): Located under the left rear seat of the vehicle.
  5. Manual The Climate Control Module is located in the center of the dashboard.
  6. Underneath the driver’s seat.
  7. Under the front passenger’s seat is a storage compartment.

Passenger Air Bag Module is an acronym that stands for Passenger Air Bag Module.

Module for the Power Liftgate The “D” pillar on the left.

Powertrain Control Module (PCM) (MKX) Located in the right front of the engine compartment.

Frontal Side Air Bag Module (Left Front) Located on the left “B” pillar.

Driver’s side air curtain module is located on the left “D” pillar.

The Smart Wiper Module (Edge) is located on the left rear of the engine compartment. The Smart Wiper Module (MKX) is located on the left rear of the engine compartment. The Steering Angle Sensor Module (SASM) is located in the center of the steering column. Rick Muscoplat posted a blog entry on

Ford Edge Check Engine Light

Please wait for the page to load completely.

See also:  Fix codes P0442, P0456 on Ford? (Correct answer)

What Does the Check Engine Light Mean?

It’s the check engine light on your Ford Edge that’s one of the most frequently misinterpreted lights or indications on a vehicle. The check engine light is a component of the onboard diagnostics system, and it can appear in a variety of configurations. An engine symbol, a message such as “Check Engine,” or a mix of the two are all possible with a check engine sign. There are two colors for this light: amber and red, and it indicates that it is part of the diagnostics system present in your car.

Some of them include adjusting the ignition timing of automatic gearboxes, managing the engine speed, and applying stability control, to mention a few examples from a long list.

It might be anything as simple as your gas cap being loose, or something as severe as your engine banging.

Our Fordservice department can assist you in determining which code is causing your check engine light to illuminate or in determining why your check engine light is on.

Will the check engine light reset itself?

If the problem or code that caused the check engine light to illuminate is resolved, the check engine light on your Ford Edge will turn off more frequently. For example, if a loose gas cap was the reason of your check engine light going on, once the cap is tightened, the light will turn off by itself within a few minutes. If your catalytic converter is failing and you’ve been doing a lot of stop-and-go driving, it’s possible that the check engine light has been illuminated owing to the excessive amount of work the converter has been doing.

You will need to bring the vehicle in to Coggin Ford Jacksonville if your commute exceeds that amount and the light is still on.

Ford Edge Check Engine Light Codes

When the check engine light shines on your vehicle’s dashboard, it may be rather frightening to see that small light suddenly illuminate, but in truth, it is not anything that should drive you to shut down in panic right immediately. When you hear the phrase diagnostic trouble codes (DTC), this is simply another word for the codes that appear on your dashboard. These are automotive computer codes that are kept by the ECM, also known as the OBD (on-board computer diagnostic system) in your Edge and are accessible through the vehicle’s dashboard.

While this may appear to be a daunting task, with a little patience, tackling major diagnostics can provide you with valuable information about your car and will also allow the Check Engine Light to perform what it was intended to do: serve as a pointer.

An illuminated Check Engine Light is not always accompanied by obvious and useful car symptoms, as is the case in this case. Because there are hundreds of different OBD codes, there are also hundreds of conceivable causes for the indicator to be illuminated, including the following:

  • Problems with the computer output circuit
  • A loose gas cap or a missing gas cap
  • Problems with the emissions controls
  • Ignition system failures due to faulty spark plugs Battery that has seen better days
  • Problems with transmission
  • Sensor for oxygen
  • Problems with the fuel and air metering systems

This is why it is critical for someone who does not have a great deal of automotive expertise to refrain from making assumptions about what a code indicates. If the engine light turns on as a result of a valid worry, you run the danger of further harming your vehicle if you do not address the problem immediately. When your check engine light illuminates, you should schedule an appointment with a skilled Ford repair as soon as possible. For more information, call Coggin Ford Jacksonville at 9047478996 or book your check engine light service online now!

How much does it cost to get the engine light checked?

In most cases, the cost of a check engine light diagnostic and testing is between $88 and $111. The good news is that Coggin Ford Jacksonville provides comprehensive multi-point inspections as well as free diagnostics in the majority of situations to assist you in determining the source of your check engine light. The check engine light can indicate a variety of problems ranging from a loose gas cap to a more severe failure such as a faulty catalytic converter or a problem with one of the car’s oxygen sensors, so it’s important to acquire the precise code reading and diagnostic.

Ford Edge Check Engine Light

If the check engine light on your Ford Edge begins to flash, it indicates that there is a problem that requires immediate care, and your vehicle should be taken in as soon as possible. An illuminated warning light signifies that the situation is potentially dangerous and that, if not addressed immediately, the vehicle may suffer irreversible harm. When this indicator blinks, it typically signifies that the engine has experienced a precise misfire, enabling unburned gasoline to escape into the exhaust.

Some owners wonder if spark plugs are responsible for the check engine light flashing.

It is possible for the engine to misfire if the spark plug is damaged, worn out, or contaminated.

To speak with our team of automotive specialists at Coggin Ford Jacksonville right now, please phone 9047478996 or complete our online contact form.

Check Engine Light Service Ford Edge

What do you do when you’re traveling in your Ford Edge and a yellow light appears on your dashboard, indicating that you need to “Check Engine”? Your heart falls a little, if you’re like the majority of Ford owners, since you have no idea what that light is trying to tell you or how you should respond. Stress can be exacerbated by apprehension about the unknown (or the potential expense of the unknown). Nonetheless, take a big breath and remember that just because the light is on does not mean you have to pull over to the side of the road and contact a tow truck, it is highly advised that you have your Ford Edge checked out right away.

See also:  2009 Ford Explorer Module Locations? (Question)

A computer activates your check engine light when your Ford Edge’s ECM (electronic control module), which is the vehicle’s onboard computer, detects a problem in the mechanical control system that it is unable to resolve.

This code is scanned by our Ford vehicle repair experts at Coggin Ford Jacksonville using an electronic scan instrument, which they use to diagnose the problem.

However, while this code will inform you of the problem that has been found, a real diagnosis will still require a qualified expert to demonstrate the problem and fix it.

How many miles can you drive with the check engine light?

It might be anything from a faulty sensor to faulty plug wires that require replacement. As a result, if your check engine light is on, we urge that you pull over and contact Coggin Ford Jacksonville so that we can determine if your car is safe to drive in or whether a tow truck is necessary. Because each check engine code has a different level of severity, it is impossible to forecast how many miles you will be able to drive while the warning light is illuminated. Attempting to comprehend the code and then planning your tactics accordingly is the best course of action.

Is it safe to drive your Ford Edge with the check engine light on?

As a result, this question is not extremely correct because everything is dependent on the severity of the problem. If the problem is a small one, such as a loose gas cap, you should be able to continue driving without incident. This is frequently signaled by an instinctual glow of the check engine light on the dashboard. The performance of your car may have changed, which might be an indicator of a more serious problem with the vehicle. There is an urgent problem with your Ford Edge if the check engine light starts flashing.

Please contact the professionals at Coggin Ford Jacksonville by phone at 9047478996 so that you can detail the problems.

Ford Edge Check Engine Light Flashing

We have learned from years of delivering Check Engine Light Diagnosis Service that there are numerous practical reasons of an illuminated Check Engine Light, including something as simple as a loose gas cap. We know this because we have seen it happen many times. To name a few other practical reasons for a Check Engine Light, there are a broken oxygen sensor, a faulty head gasket, an issue with the fuel injection system, an unclean mass airflow sensor, a faulty emissions control element, and defective spark plugs.

When this occurs, the Check Engine Light is turned off, and you may walk out of the repair shop certain that your Ford problem has been resolved.

The sensors are constantly sensing situations and transmitting data to the electronic control unit, which is always changing.

However, this is the limitation of the Check Engine Light – it will not tell you what is wrong with your vehicle or what you need do to fix it.

Our Check Engine Light Diagnosis Service isolates the root cause of the problem and delivers you with a recommendation on what to do next from a Particularly Qualified Service specialist. Coggin Ford Jacksonville is proud to provide this service.

What could cause the check engine light to come on in a Ford Edge?

Your gas cap might be loose or need to be replaced if your check engine light turns on. If this is the case, tightening or replacing your gas cap could solve the problem. Similar to how a malfunctioning check engine light might signal the presence of an imaginative issue, which could result in ingenious damage to your engine and result in a large repair price. The check engine light will either glow or blink depending on your vehicle’s make and model. In most cases, a constant glow signifies something less imaginative, but a flashing check engine light signals that your vehicle’s engine is experiencing ingenious issue and that servicing is required as soon as possible.

The following is a list of the most common reasons that your check engine light may illuminate:

  • There is a vacuum leak in your Ford Edge. Every Ford Edge is equipped with a vacuum system that is capable of performing a wider range of tasks. The vacuum system also contributes to minimize harmful emissions by directing fumes away from the engine when fuel evaporates through it. Whether your engine’s RPM is high at idle or surges at random, a vacuum leak might be the source of the problem. One of the most recent and frequent reasons for vacuum hose cracking is that the Ford Edge gas cap is loose, damaged, missing, or otherwise compromised over time
  • One of the most recent and frequent causes is that the Ford Edge gas cap is loose, damaged, or otherwise compromised. There are several functions performed by the gas cap on your Ford Edge vehicle. In addition to preventing gas fumes from being emitted when you are not driving, it also helps to maintain pressure within the fuel tank by securing the fuel system. What happens if you have a faulty gasoline cap on your vehicle? If your gas cap has been in place for a long time or has a burst seal, you may experience gasoline loss due to evaporation, resulting in repeated journeys to the gas station. Fortunately, replacing a gas cap is not a costly endeavor. If your Ford Edge’s check engine light illuminates quickly after you fill the tank with gas, the first thing you should check is that the cap isn’t loose — or that it’s still on the car’s roof or at the fuel pump
  • In order to keep your Ford Edge running smoothly, new spark plugs or plug wires are required. The spark plugs in your vehicle’s engine are the components that ignite the air/fuel combination in the combustion chamber of the vehicle’s engine. This explosion is responsible for the movement of the pistons and the operation of the engine. The spark plug wires are responsible for delivering the spark from the ignition coil to the spark plugs in the engine. If your spark plugs or spark plug wires are damaged or have been in use for a long period of time, you may notice poor performance and lower power. Occasionally, your engine will have difficulty starting or continuing to operate in certain severe circumstances. A blocked catalytic converter or damage to ignition coils and oxygen sensors can be caused by worn spark plugs and plug wires, resulting in more expensive repairs as a result. Your catalytic converter has failed or is about to fail. In your Ford Edge’s exhaust system, there is a catalytic converter that helps to clean the exhaust gases. One of the functions of the catalytic converter is to convert the carbon monoxide produced during the combustion process into carbon dioxide. In most cases, neglecting maintenance results in a broken catalytic converter, which is why Coggin Ford Jacksonville includes a comprehensive multi-point check with every Ford service. If you have a problem with your catalytic converter and don’t get it fixed, your Ford Edge will fail an emissions test, will have poor engine performance, and will have a severe impact on your fuel efficiency. Your automobile may also operate at a greater temperature, which might lead to additional difficulties as a result of overheating. There are problems with any aftermarket parts. If an aftermarket alarm, exhaust, or other accessory is not properly fitted, it can cause significant damage to your Ford Edge. It is possible that certain aftermarket parts and accessories will cause the battery to fail, the check engine light to illuminate, or even the vehicle to fail to start. If these concerns appear to be straightforward, bring your Edge to Ford and our team of experienced experts will inspect it to confirm that your aftermarket parts were properly fitted and are not creating any problems. The cost of purchasing components, particularly aftermarket parts and accessories, or utilizing OEM elements in the first place may be slightly more, but it might save you money in the long run by avoiding the expense of having to rectify faulty work and damage caused by poor installation work. The battery is either low in charge or completely dead. The battery in your Ford Edge is on the verge of failing completely. Your car won’t start, it won’t illuminate the road ahead, it won’t play the radio, and it won’t charge your phone if it doesn’t have a battery. Car batteries today last far longer than they did only a few decades ago, and they require little to no maintenance. Prices for new Fords vary depending on the model you drive, so be sure to check out our current servicing coupons and promotions. A new O2 Sensor (Oxygen Sensor) is required for your vehicle. The Oxygen Sensor, often known as the O2 sensor, is responsible for measuring the quantity of oxygen present in your exhaust. When there is an excess of oxygen in your exhaust system, gasoline burns more quickly and your vehicle becomes less fuel efficient, which reduces its overall efficiency. As a result, what will happen if I do not replace your oxygen sensor? An incorrectly functioning sensor can not only reduce your miles per gallon, but it can also cause damage to your catalytic converter and the spark plugs in your Ford Edge. The oxygen sensor transmits data to the vehicle’s onboard computer, which uses the information to calculate the proper combination of air and fuel to be introduced into the engine’s cylinders. A faulty oxygen sensor can also cause a vehicle to fail an emissions test
  • In this case, the mass airflow sensor (commonly known as the MAF) must be replaced. The mass airflow sensor in your Ford Edge is responsible for determining how much fuel is required to run your engine effectively. It does this by measuring the amount of air that is introduced into the engine. The mass airflow sensor, which is a component of the engine management system, assists the engine in responding to certain changes, such as altitude. The failure of the mass airflow sensor in your Ford Edge may manifest itself as difficulty starting, rough idling, or an abrupt shift in the position of the throttle pedal.
See also:  GM service bulletin on Fluid flushes? (Correct answer)

Ford Edge Oxygen Sensor

Your Ford Edge will be relieved to learn that the hunt for the appropriate Oxygen Sensor goods you’ve been looking for is finally complete! Advance Auto Parts provides 40 different Oxygen Sensors for your car, all of which are available for delivery or in-store pickup at your convenience. The greatest news is that our Ford Edge Oxygen Sensor goods are reasonably priced, starting at just $28.99. In terms of components and goods for your Ford Edge, you want to make sure that only reputable companies are used.

Bosch and NTK are two of the most well-known manufacturers of Oxygen Sensor products.

To help you shop with confidence, we’ve included reviews of our OEM and aftermarket Oxygen Sensor items on our website.

You may shop online and have your purchases delivered to your doorstep at the greatest possible price and quality.

FAQs forFord Edge Oxygen Sensor Products

Leave a Comment

Your email address will not be published. Required fields are marked *