Abs light on, traction control light on, Impala? (Best solution)

  • When the ABS and Traction Control lights illuminate, it is typically due to a faulty wheel or speed sensor or an ABS module failure. An OBDII scanner can read trouble codes stored in the ECU, but you need a mechanic to test these codes to identify the cause and corresponding fix for the issue.

Why would my traction control light and ABS light come on?

The ABS and Traction Control lights come on whenever the vehicle’s computer or PCM detects a malfunction, a faulty wheel sensor, or other mechanical failures. These warning lights do not imply anything severe by themselves but may point to a graver problem when paired with the main brake light going off.

Is it safe to drive with ABS and traction light on?

If the TCS and the ABS warning lights both come on, along with the red main brake warning light, you should not drive the car until the problem has been fixed. Your entire braking system is affected, and may not be able to stop your vehicle when you need it to. Have your vehicle towed to a repair shop.

How much does it cost to fix a StabiliTrak on a Chevy Impala?

Replacing the traction control system, or StabiliTrak, on a car typically costs between $80 and $190.

How do you reset the traction control light on a Chevy Impala?

There’s no such thing as “reset the traction control light” itself. To extinguish the light, you must first correctly diagnose and then repair the system malfunction that is causing the light to illuminate. When that is done first, then you can have it reset if it doesn’t go out by itself.

How much does it cost to fix ABS and traction control?

A lot of garages will be able to fix your ABS control module for somewhere between $340 and $1,100. The huge price difference isn’t really affected by labor costs, which range between $80 and $120.

How much does it cost to fix ABS?

Many ABS components are very accessible, so labor for most repairs will not run high typically in the $100 to $150 range. A typical ABS sensor will cost about $80 to $125 however, on some makes and models the sensor is part of a hub/bearing assembly (GM, Ford, some others) and the price will rise to around $350.

How much does it cost to fix an ABS sensor?

The average ABS wheel speed sensor replacement cost is between $200 and $400 per sensor, depending on the car model and labor costs. You can expect to pay about $100 to $150 for the wheel speed sensor and another $100 to $300 for the labor.

Can worn brake pads cause ABS light to come on?

To Be Clear, Worn Brakes CAN Cause The ABS Light To Come On, But It’s Not Why You Think. Your brakes and your ABS are not the same, even though they work together. Your ABS system has its own electrical control unit which is separate from your braking system, even though the ABS and your brakes work together.

Why does my Chevy Impala say StabiliTrak?

The ‘Service StabiliTrak Warning’ indicates the system is not responding or operating as it should. A failed brake switch will also disable the system as well as the wrong size of tire. The cost of replacing the Impala’s wheel sensor averages $100-$120 in parts and labor.

What is service traction control for the Impala?

The traction control sequence on the Chevrolet Impala limits the power produced by the engine when the system determines the drive is losing control of the car. It is possible to disable this feature for the driving cycle, although it is automatically reenabled each time you crank the Impala’s engine.

What causes Service StabiliTrak light to come on?

Some of the things that could cause the “service StabiliTrak” light to come on include: Faulty input sensor. Malfunctioning controller. Poor system connection.

What is TC light on Chevy Impala?

If You see the TC light on Your Chevrolet Impala, it means that the traction control system has been activated. When this happens, power to Your engine is being limited when the system has detected the drive is losing some control of the car.

What does ABS mean on a Chevy Impala?

The anti-lock braking (ABS) system is used to maintain wheel motion and traction while braking, accelerating or cornering on a slippery surface.

Where is the traction control sensor located?

There are NO traction control sensors, the system use wheel speed sensors to identify if one of the wheels are turning at a significantly higher rate than others. The wheel speed sensors are generally located behind the wheel hub that is looking at the geared wheel.

Abs light on, traction control light on, Impala

Shops are reporting difficulties with Impala vehicles that have the ABS light illuminated and the traction control light illuminated. A ‘Service Stability System’ notice may appear on the driver information center of vehicles manufactured in 2012 and 2013. The problem affects vehicles manufactured in 2013 and may also appear on vehicles manufactured in 2012. In addition, the PCM may hold a variety of issue codes for various problems. Additionally, the instrument cluster may not function properly.

It all adds up to a complete and utter disaster.

ABS light on, traction control light on Service stability message caused by chaffed wiring harness

A chaffed wire harness is the most likely source of the problem. The wiring harness has been reported to rub against the transmission or engine and rub through, resulting in wires being shorted, according to repair shops. The harness at the left rear side of the front cylinder head on vehicles with a state-specific emissions system (California, Connecticut, Delaware, Maine, Maryland, Massachusetts, New Jersey, New York, Oregon, Pennsylvania, Rhode Island, Vermont, and Washington) is not secured by a tie-strap, which may allow the harness to rub against the engine cylinder head.

THE PRESSURE OF MAFABSAC Relays for the SAI pump, control, and VLV Sensor for the pressure in the fuel line Sensor for VAC/BAR ASM for the pump and brake vacuum assist Injectors are an oddity.

B1 knock sensor is a sensor that detects knocking.

Fix chaffed wiring harness to correct the problem

A chaffed wire harness is the most likely source of the issue. The wiring harness has been reported to rub against the transmission or engine and rub through, resulting in wires being shorted, according to the shops. There is no tie-strap to secure the harness at the left rear side of the front cylinder head on vehicles with a state-specific emissions system (California; Connecticut; Delaware; Maine; Maryland; Massachusetts; New Jersey; New York; Oregon; Pennsylvania; Rhode Island; Vermont; and Washington).

Pressure applied by MAFABSAC Control/VLV relays for the SAI pump and control system Pressure sensor for the fuel line Sensor for VAC and BAR Brake vacuum assist, pump ASM Contrary to expectations, injectors Additionally, injectors Sensing device B1 for knocking Position sensor for the crankshaft an O2 sensor designated by the designation B1S1.

06 Impala – Service Traction control / ABS.

06 Impala – Service Traction control / Anti-lock braking system. Hello, I’m new to the forum and could need some assistance. I have a 06 Impala that all of a sudden is emitting the warning ‘Service traction control’ and the ABS light is illuminated in conjunction with this. Now, I’ve taken the car to a shop twice to have the error codes looked at, but nothing has come up as a result. I can see why it happened the first time; it was really cold here at the time, and I noticed the car calibrating the GP sensor, so I shrugged it off.

So far, my wife has only informed me of mistakes that appear on the dashboard, which has been the case until today!

Then there’s the service traction control / anti-lock braking system.

I was talking to a local GM dealer, and he told me that the wheel bearing is most likely the problem, and that if it isn’t that, the wiring harness is most likely the problem, all for a wonderful price of $520.00.

Another thing to note is that the door locks will automatically lock while the car is warming up. The automobile is not in drive or anything like that. Any thoughts or suggestions would be much appreciated. TX.

How to Fix the ABS/Traction Control Light on a 04 Impala

This Instructable will teach you how to fix the ABS/TRACTION CONTROL light that comes on in your automobile on a budget and with minimal effort. Don’t let the mechanics get away with your cash! This is a simple remedy that will just take a few minutes.

See also:  Bleed clutch slave cylinder? (Correct answer)

Step 1: Things You Will Need

This Instructable will teach you how to fix the ABS/TRACTION CONTROL light that comes on in your automobile on a budget and with minimal tools and experience. Allowing the technicians to grab your money is not advisable! This is a SIMPLE repair that will only take a few minutes.

Step 2:

When you want to start your car, does the ABS/Traction Control light come on sometimes or all of the time, regardless of whether or not you use the traction control button? If you have a scanner, it will inform you that it is a component of a failing ABS system or that there is a problem with the grounding. It is the most costly portion of the system that has to be changed, according to mechanics, and this includes your ABS, hub, speedometer sensor, pump module, and so on and so forth. Even while the scanner is correct in that there is a poor ground connection, none of these objects have individual sensors that can tell you if it is the ground connection on that particular part that is defective or needs to be repaired.

You will not be responsible for any of the following actions taken by your automobile at any time while you are driving it.

Step 3: The Fix

Locate your ABS pump module (INSPECT IT, if it seems to be leaking or you notice leaking, you should repair this part), which is located on the driver’s side of the vehicle. Go to the unit and trace the black wire coming out of the module to the driver’s side fender, where it is fastened to (see the pics). This is either a Metric 10 or a Metric 13 bolt, depending on your preference. Unbolt the lug and store the bolt and lug somewhere on your vehicle where you can clean them up later (you only have a few spots, the wire is not that long.) I utilized the car’s ECU/computer because it had been exposed due to the removal of my air filter and it was completely flat.

Clean the lug and bolt with the wire brush, being sure to get into the bolt hole as well.

Di-Electric Grease should be applied to both sides of the LUG, on the bolt, and in the bolt hole of the LUG.

YOU HAVE COMPLETED YOUR WORK! Reward yourself since you just saved many hundred dollars by completing this task yourself.

Step 4: Optional

If you have the optional resources, you will undoubtedly spare yourself the difficulties of having to go through this process again and again. Meanwhile, as the lug is being removed from the wire, heat up your soldering iron and add a little amount of solder to the area where the lug was crimped onto the wire, leaving a small amount of wire exposed on both sides of the crimp. Wrap the soldered wire in heat shrink tubing and wrap it tightly around it all the way to the end of the crimp where it is visible.

  1. My issues were resolved as a result of this.
  2. This should be tried after the previous patch if the previous fix does not work for you: You’ll need a few extra equipment for this, including a jack and a tire iron, to get the lug nuts off your tire and put them back on.
  3. There have been multiple articles published by General Motors about this harness not being properly constructed and the connectors to which the wires are crimped that are used to attach them to the harness failing.
  4. Turn off your vehicle, jack up the effected side of the vehicle, This item costs around $45 at Autozone; however, you may also get it on Amazon or Rockauto (you want the ABS Wheel HUB connector).
  5. THIS SHOULD RESOLUTION THE PROBLEM.
  6. If you still have this problem, you may go on YouTube for a how-to video on how to replace the ABS hub on either side of your car.

1 Person Made This Project!

When your Chevrolet Impala’s ABS Light illuminates, it means that the vehicle has failed a self-diagnostic cycle. This light shows that the Impala does not have Anti-Lock brakes, and hence does not give the further safety that these brakes would provide. When braking, your Impala’s anti-lock braking system (ABS) makes use of a network of sensors to calculate wheel speed. The system will apply the greatest amount of braking to a wheel that is starting to lock up in order to prevent the vehicle from sliding.

A side effect of skidding tires is that they cause flat patches in the tire, which may be both annoying and potentially hazardous.

ABS also gives you the ability to control the car as it is slowing down, and it has been around for so long that many drivers have never driven a vehicle that did not have the technology.

Is it Safe to Drive Your Impala?

The ABS light is distinct from the brake warning light on the car’s dashboard. A malfunctioning physical braking system signifies that your Chevrolet Impala is unsafe to be behind the wheel, and the brake light illuminates to signal this. Yes, you may operate your Impala when the ABS light is illuminated. Is it safe to use? Particularly hazardous is driving when it is pouring, snowing, or the road surface is loose or uneven. It is also less convenient. As a result, we urge that you get the ABS system repaired as soon as feasible.

Chevy Impala ABS Light On Causes

A decent code scanner will frequently be able to tell you which portion of the ABS system is malfunctioning. This information will not be provided by every OBDII scanner, however. A good one will take care of you. In most cases, car parts retailers will provide you with a free scanning service that they would be pleased to let you take use of. The following are the three most prevalent reasons for the ABS light to illuminate:

1.Wheel Speed Sensor

The wheel speed sensors are in charge of monitoring the wheel speed and transmitting that information back to the computer system for analysis. If one of the wheels is moving more slowly than the others, it is on the verge of locking up completely. The anti-lock braking system (ABS) is then activated on that wheel to prevent it from locking. When this sensor is no longer transmitting a signal to your Impala’s anti-lock braking system, the system is no longer operating correctly, and the ABS light will illuminate on the instrument panel.

2.ABS Module

The ABS module is responsible for the operation of the antilock braking system. This module is responsible for the physical control of the anti-lock braking system. The ABS light will illuminate if the system gets broken and is no longer capable of controlling all four brakes. Corrosion is the most prevalent cause of module failure, according to industry standards.

3.ABS Fluid Level

The ABS light will illuminate if the fluid level in the ABS lines is too low to maintain pressure in the lines. The ABS will no longer be able to physically activate if the pressure is not maintained.

Conclusion

The ABS light will illuminate if the fluid level is insufficient to maintain pressure in the ABS lines. The ABS will be unable to physically activate if the pressure is not applied.

Chevrolet Impala Traction Control Light On Problems

Owners of the Chevrolet Impala have reported 49 issues relating to the traction control indicator being on (under the traction control system category). The most current problems that have been reported are shown below. Please also have a look at the statistics and dependability analysis of the Chevrolet Impala based on all of the faults that have been recorded for the vehicle.

36Traction Control Light On problem of the 2002 Chevrolet Impala

Failure occurred on February 10, 2011. The contact has a 2002 Chevrolet Impala, which he purchased from his father. A traction control warning light had been activated when the contact indicated that his vehicle’s traction control system had malfunctioned. A result of the failure was a significant increase in stopping distance.

After inspecting the car, the dealer determined that the traction control system needed to be fixed. The automobile was brought back to life. According to the failure mileage, the vehicle had 70,000 miles and the current mileage was 80,000 miles. See all troubles of the 2002 Chevrolet Impala .

37Traction Control Light On problem of the 2001 Chevrolet Impala

Failure occurred on January 15, 2011. I have a 2001 Chevrolet Impala LS with around 80k miles on the odometer. When the weather began to deteriorate, the traction system light illuminated, which was understandable given the circumstances. I pulled it off since I didn’t care for it. When I get into my car and switch it on, the warning lights for the anti-lock braking system, traction control, and ‘service traction system’ illuminate. Even when the ‘service traction light’ is turned off, I would want to turn off the other light as well.

See also:  How long should brake pads last? (TOP 5 Tips)

Hundreds of individuals around the United States are experiencing a similar problem with this particular model, which dates back to the years 2001-2004.

38Traction Control Light On problem of the 2010 Chevrolet Impala

Failure occurred on December 5, 2010. The 2010 Chevrolet Impala was traveling at highway speeds and under cruise control at approximately 65 mph. The automobile had a front twitch that progressed to a vibration. The boat began to see a surge around one hour into the voyage. The traction control light illuminated, followed by the check engine light a couple of seconds later, and the message display flashed traction control failure, drive at lower speeds, and ignition failure, among other things.

This is the second time something like this has occurred.

See a list of all the problems with the 2010 Chevrolet Impala.

39Traction Control Light On problem of the 2007 Chevrolet Impala

Failure occurred on September 30, 2010. It is owned by the contact, who drives a 2007 Chevrolet Impala 3lt (na). After leaving a stop light or stop sign, the contact said that the tires spun out and that the traction control light lighted on the instrument panel while driving the car. The malfunction happened on an irregular basis. The car was transported to a licensed dealer, but the malfunction could not be replicated by the technicians. The automobile had not been fixed at the time of writing.

See a list of all the problems with the 2007 Chevrolet Impala.

40Traction Control Light On problem of the 2009 Chevrolet Impala

Failure occurred on September 15, 2010. The contact has a 2009 Chevrolet Impala, which he purchased recently. The car came to a complete stop while traveling at about 65 mph, and the service traction control system warning light lighted. Upon arrival at the dealership, it was discovered that unidentified sensors relating to the traction control needed to be swapped out. However, despite the fact that the car was fixed, the malfunction recurred. The problem was communicated to the manufacturer in a timely manner.

See a list of all the problems with the 2009 Chevrolet Impala.

41Traction Control Light On problem of the 2001 Chevrolet Impala

Failure occurred on January 6, 2010. It’s been going on for a few months now, and it’s getting worse. It is more obvious when I am making a right or left turn or when I am driving away from the curb where I have parallel parked my vehicle. There is a whining sound coming from the engine, and the engine gets slow, and the service traction system and trac off lights illuminate.

The noise ceases and the lights go off as soon as I straighten the steering wheel. When I am turning right or left, it also occurs, and I must break while I am navigating the corner.

42Traction Control Light On problem of the 2001 Chevrolet Impala

Failure occurred on January 6, 2010. Apparently, this has been going on for a few months. When I am turning right or left or pulling away from parallel parking, I notice that the engine produces a grinding noise, gets slow, and the service traction system and the trac off lights illuminate on the dashboard. When I straighten the steering wheel, the noise stops and the lights turn off as well. Whenever I need to stop when making a right or left turn, the car behaves in the same manner.

43Traction Control Light On problem of the 2007 Chevrolet Impala

Failure occurred on January 6, 2010. As a result, I took my vehicle to the dealership for service, where I was informed that the hub assembly for the left side driver side was covered under warranty and that I would also need to replace my front rotors and brake pads (I wasn’t having any problems with my brakes, but because they said they needed to be replaced, I went ahead and replaced them). After the repairs were made and my vehicle was ‘road-tested,’ I was able to pick up my vehicle. However, shortly after leaving the dealership, both the ABS and traction service lights illuminated again, prompting me to contact and book an appointment for two days later.

I was a little hesitant because my service two days previous had cost $224.90, but I wanted to know what the problem was, so I agreed to have it looked at.

I look on the internet for more information and discover that not only has this happened to me, but it has happened to several others as well, indicating that this is a manufacturer defect that should be covered.

44Traction Control Light On problem of the 2008 Chevrolet Impala

01/06/2010 – Date of failure The Abstraction Control service light kept coming on, so I took it to the dealership for service. They determined that the problem was with the hub assembly on the left side of the vehicle, which was covered under warranty, and that I needed to replace my front rotors and brake pads (I wasn’t having any problems with my brakes, but because they said they needed replacing, I went along with it.) My vehicle was ‘road-tested’ after the repairs were completed, and I was able to pick up my vehicle.

However, shortly after leaving the dealership, both the ABS and traction service lights illuminated again, prompting me to contact the dealership, which scheduled me in for an appointment two days later.

I was a little hesitant because my service two days previous had cost $224.90, but I wanted to know what was wrong, so I consented.

After checking the internet for more information, I find out that not only has this happened to me, but to several other people as well, and that this is clearly a manufacturer defect that should be covered.

However, how do I know that the dealership did not cause the problem/defect by digging deeper to find out why the service lights were coming on and damaging the wire?

45Traction Control Light On problem of the 2001 Chevrolet Impala

Failure occurred on December 30, 2009. I purchased my 2001 Chevrolet Impala LS in 2004 and drove it until December 2009, during which time it was in excellent condition. When I first noticed this, my car’s ‘traction active’ light illuminated whenever I applied the brakes. After a couple of weeks of this light flashing more and more frequently (4-6 times daily), I had an incident in which my brakes jammed up, the brake pedal became difficult to press, and I came close to colliding with a car in front of me.

However, the problem with my brakes became more frequent, occurring at least once or twice daily (not every time, but 1-2 times a day), and the abs light began to illuminate.

After doing some research online, I discovered a slew of complaints from Impala owners all across the United States who were experiencing the same problem with the traction control engaged and the ABS lights illuminated.

The cost of this module, as well as the repair, came to around $1,000.00.

46Traction Control Light On problem of the 2009 Chevrolet Impala

Failure occurred on September 9, 2009. The contact has a 2009 Chevrolet Impala, which he purchased recently. After traveling about 60 miles per hour, the contact reported that his vehicle’s traction control warning light came on and the engine shut down. The contact was able to successfully merge into the emergency lane. After many efforts, the car was successfully starting and sent to a dealership for further investigation. The technician determined that the throttle and accelerator pedals were in need of replacement.

47Traction Control Light On problem of the 2001 Chevrolet Impala

Failure occurred on March 20, 2009. Driving to work, I was making a tight right turn when I heard a grinding noise coming from my car. It was at this point that I noticed the traction activity indicator illuminated. Just as I was getting ready to drive into a parking space on the left, the noise started up again, but this time it was accompanied by a delay in both my stopping and turning. After work, I drove out of the parking lot without any issues, so I don’t pay any attention to it anymore.

See also:  Clean an electronic throttle body? (Solved)

I literally had to wrestle with the steering wheel to get the car to go forward with my turn.

The fact that the same problem happens if the traction is disabled, albeit not as badly, was only discovered two months ago, and that it had something to do with part number 10340313 and part number 1034314, the ABS harness, which can only be acquired through the dealer or on gmpartsdirect.com.

The other problem I’m having is that the turn signal stops functioning. I have to press down on the danger button to get it to work again, and on some occasions I have to touch the dash button.

48Traction Control Light On problem of the 2008 Chevrolet Impala

Failure occurred on February 17, 2009. While traveling at 60 mph, the traction control and anti-lock braking system service lights illuminate, as does the ABS brake service light. The vehicle subsequently slows its speed to no more than 35-40 mph, and this is with the gas pedal down all the way. It has been happening since the beginning. I’ve replaced the harness and the wheel hub, but the problem persists, sometimes in really hazardous scenarios such as while driving on a highway with a vehicle behind you and the car swings from 60 mph to 40 mph in a heartbeat.

According to the dealership, this is a frequent electrical problem with GM vehicles from 2006 to 2009.

49Traction Control Light On problem of the 2002 Chevrolet Impala

Failure occurred on March 2, 2008. Traction is activated on a regular basis. The ‘service traction system’ and ‘abs’ lights are activated on a regular basis. My mechanic changed a handful of parts throughout the course of the previous spring and summer, but the problem persisted. I am unable to tell you exactly what those parts were since I have not yet located my receipts for the job. During the spring and summer of last year, the traction did not truly engage, although the light did illuminate.

The body module was replaced in the fall of last year.

My understanding is that there hasn’t been any sort of recall.

When I come to a complete stop at a stop signal or stop sign, or when I make a turn, my traction may be activated.

2005 Chevrolet Impala Service Traction Control/ABS Lights On

12th of June, 2015, Problem8

Impala LS 3.8L V6

A D V E R T I S E M E N T S A D V E R T I S E M E N T S A D V E R T I S E M E N T S A D V E R T I S E M E N T S A D V E R T I S E M E N T S A D V E R T I S E M E N T S A D V E R T I S E M E N T S A D V E R T I S E M E N T S A The traction control indicator illuminated, signaling the beginning of the problem. As a result, there was nothing I could have done to have it rectified, and the ABS light illuminated. Taken the vehicle in to be looked at by a technician, who informed him that in order to correct the problem, he would have to replace the ABS Control Module as well as the axle.

I attempted to apply for a credit card so that I could make payments, but was denied owing to my poor credit history.

This is a problem that many individuals are experiencing, and it is not safe.

While I’ve done everything else, I can’t help but think whether it’s the ABS Control Module that has to be replaced. ‘problem7’ was created by Daniel M. in Katy, TX, United States on June 7, 2012.

Impala V6

I’ve been experiencing difficulties for the past two months. My message board is illuminated, and the Service Traction ABS light illuminates! My wheel bearings have been changed, and I’ve had my brakes redone all the way around my car, and it still happens. The majority of the time, this occurs when I am backing up or turning the vehicle. This morning, I took it to be checked by a diagnostic computer, and it was determined that there were no problems with the car. Then, about a mile farther down the road, the lights went out once more.

Is there a recall in effect?

I’ve reached the point where I’m afraid to get into my automobile.

-lstone,Mortons Gap, Kentucky, United Statesproblem 6th of June, 2012

Impala LT 3.8L

The service traction system, anti-lock braking system, and traction off lights all illuminate at the same time. If you turn off your automobile and reactivate it, everything will be restored. Has been in the shop (at a used car dealership) approximately six times. In addition, two wire harnesses were changed. They replaced the front sensors twice each, as well as the right rear sensor once. They are putting in tremendous effort. There is no payment for anything, with the exception of components only on the back one.

  1. It’s a 2000 Chevrolet Impala that my wife put 163000 miles on and it’s still running well and without issues.
  2. The used car dealer from whom I purchased it even brought it to the local General Motors dealership and had it diagnosed out of his own cash, following their recommendations, which did not work.
  3. I looked up the topic on the internet and was surprised to see how widespread it is.
  4. This problem has existed for many years and affects thousands of automobiles.
  5. How is it possible to have this problem for so many years and not solve it properly?
  6. This is a serious safety issue, and some sort of regulatory agency should be on the case to address it.
  7. This has the potential to cause death or significant injury to people.
  8. As a last word, I’d like to say ‘BULLSHIT.’ -Tony L., Van Wert, Ohio, United Statesproblem5 1st of June, 2012

Impala 3.2ll V6

A D V E R T I S E M E N T S A D V E R T I S E M E N T S A D V E R T I S E M E N T S A D V E R T I S E M E N T S A D V E R T I S E M E N T S A D V E R T I S E M E N T S A D V E R T I S E M E N T S A D V E R T I S E M E N T S A The traction light remains on, and it has an impact on the vehicle’s braking performance, particularly when the road is slick, but it also has an impact when the road is dry.

When it malfunctions, you may feel it shaking and hear a grinding sound! -Jeremy R., Flint, Michigan, United States, problem4 on February 11, 2011

Impala LS 3.8L V6

I recently purchased a ’05 Impala since I enjoyed my previous ’02 model so much. However, on a test drive at the dealership, the ‘Service Traction Control’ sign illuminated as we began driving, despite the fact that we had just been struck by a snow storm a few days prior. Because the roads were still covered with slush, I figured that was what it was supposed to be doing. My husband informed the salesman that the brakes seemed like they needed to be changed, and the dealership made the necessary repairs before we drove the car home (the front set only).

Of However, because my previous vehicle did not have traction control, I am unable to determine how the vehicle should behave when there is a traction issue on the road.

-Melissa W., Tuttle, Oklahoma, United States Find these common complaint terms on CarComplaints.com by searching for them.

Impala 3.2L V6

Other issues were brought to the dealer’s attention in September 2010. It was advised that the cost of repairing the abs/trac issue would exceed $2700.00. Pnowlen, Euless, TX, USproblem2: Vehicle was refused repair since it did not interfere with vehicle operation.

Impala 3.4L

The ABS and traction control lights are both illuminated. Neither of them is in proper operating order. I’ve read numerous blogs on this identical dilemma, and it appears that we’re all experiencing problems, but we can’t seem to find out what they are. The vehicle was taken to a couple of mechanics, who determined that the problem was with the right front speed sensor. It might cost anything between $125 and $400 to repair! Is anyone aware of any recalls or other action being taken in this regard?

If anyone has any suggestions on how to resolve this, please let me know.

Hillsboro, Ohio, United StatesShauna G.problem1

Impala 3.4 L

Once again, after traveling from Houston to Atlanta and returned two weeks later, the message center by the speedometer flashed ‘Service Traction System’ and the ABS light illuminated within a few miles of driving. After bringing it into the dealership, a technician diagnosed and replaced the Ignition Switch and Electronic Brake and Traction Control Module on the 13th of April, 2007. -howjltx,League City, Texas, United States

Leave a Comment

Your email address will not be published. Required fields are marked *