Reset oil life monitor BMW? (Perfect answer)

Locate the small odometer button near the bottom left corner of the instrument panel. Press and hold it until the service message appears. Release the button, and press and hold it again until the message says “Reset?”.

  • However, the oil life monitor cannot be reset manually on many late model BMW vehicles. You must use a reset tool. See the tools below. 1. Turn ignition key one click or press of the START/STOP button. 2. Press and hold the Instrument Cluster Set/Reset button for 10 seconds.

How do you reset the oil life on a BMW?

So this is how you reset it:

  1. Turn on your car without starting the engine. Put the key in and don’t touch any pedals then push the START button once.
  2. Hold down the RESET button.
  3. Display the ENGINE OIL.
  4. Press and hold the RESET button.
  5. Hold it again.

How do I reset my oil life monitor?

Press and hold Trip/Reset button for two seconds until “Reset for System Check” message appears. Release button. 3. Immediately press and hold button for two more seconds until “Oil 100% Reset if New” message is displayed.

How do you reset the oil life on a 2014 BMW 328i?

To reset the oil on the 2014 bmw 328i, press start once, hold the set/reset button until you see the service indicator light, press set to go to the service menu, on the oil section, press reset until the ok message appears.

Why won’t my change oil light go off?

If you are referring to the oil pressure warning light, it may be that the oil pressure is low, due most likely to excessive wear in the oiling system. Or perhaps just a faulty oil pressure switch or the wire grounding out somewhere. If it is an oil level light there is a problem with the sensor or sensor circuit.

Why is my oil change light still on?

If your oil light stays on even after changing your engine oil, you’re going to want to check the sensor first to rule out a malfunctioning sensor as the cause. Dirt and other particles can make their way into the oil pump, causing the sensor to falsely identify oil issues. The next common cause is low oil pressure.

How do you reset the oil life on a 2017 BMW 530i?

BMW 5-Series G30/G31/G38 Oil Service Light Reset Guide

  1. Hit the START button three times quickly.
  2. Hold down the RESET button.
  3. Go to the ENGINE OIL.
  4. Press and hold the RESET button.
  5. Release and then hold it again.

How do you reset the oil life on a 2015 BMW 328i?

To perform an oil reset on the 2015 bmw 328i you need to turn it on, but do not start the engine. Find the reset button on the console dash and hold it. When the light blinks and stops turn the vehicle off and wait 5 min. Your oil is now reset.

How do you reset the oil life on a 2016 BMW 328i?

To reset the oil level warning or maintenance light in your 2016 bmw 328i vehicle, turn the ignition key to the ‘on’ position and depress the gas pedal slowly three times. Release and start your vehicle and the oil light should indicate a reset.

How do you reset the oil change light on a 2017 BMW?

Locate the small odometer button near the bottom left corner of the instrument panel. Press and hold it until the service message appears. Release the button, and press and hold it again until the message says “Reset?”.

How To Reset Oil Service Light On BMW X1 F48 (2016-2021)

Bimmers, how have you been doing? I wish you the best of health at all times. If you’re already doing a BMW X1 F48 oil change at home and need to reset the service light on your car, this page will provide you with some helpful hints and recommendations. Make sure to study this one completely before moving on to the DIY section so that you can learn the tips and methods first. When you’re reading the DIY, you’ll be able to make a bit more sense of some of the stuff you’ve learned. So let’s get this party started right now.

So, when you’re through with the oil change, some of you may notice that the BMW X1 F48 has a service light illuminated.

  1. Turn on your car’s ignition without turning on the engine. Put the key in the ignition and don’t touch any of the pedals before pressing the START button once. Keep the RESET button pressed. Keep pressing and holding the RESET button until the service menu appears
  2. This will take some time. ENGINE OIL will be displayed once you click on the RESET button to bring up the various options. Once you find the ENGINE OIL, click on it again to close the window. Press and hold theRESETbutton for a few seconds. Once you’ve arrived, press and hold the RESET button until it flashes Reset
  3. Then release your finger. Hold it for a second time. Once you’ve confirmed the reset, press the RESET button one more time to complete the process.

For your information, this procedure is compatible with the BMWX1F48 (2016, 2017, 2018, 2019, 2020, 2021 model years). So that’s it for today’s tips and tricks on how to reset the oil service light on your BMW. Thanks for reading. I hope you enjoyed this article, and if you have any thoughts or suggestions, please feel free to express them in the comments area. In any case, thank you for your time and see you next time.

EASY STEPS BMW 3 Series Oil Reset Instruction

The BMW 3 Series is nearly widely regarded as the industry’s premier sports sedan. Available with rear- or all-wheel drive, the vehicle offers precise handling as well as a compact yet superbly designed interior space. In addition to a range of four-, six-, and even V8 engines, it has been available in a number of body styles, including sedans, convertibles, and wagons. Regardless of the version you pick, the recipe for a comfortable ride, a powerful engine, and a fun-to-drive experience remains same.

The track-monster M3 models push the dial all the way to the right in terms of sportiness.

Oil Reset Method 1

  1. Turn the ignition to Terminal 15, which is one turn of the key or one push of the START/STOP button away from the starting position. For a total of 10 seconds, press and hold the SET/RESET button on the instrument cluster. A service item will be displayed on the upper display screen in the future. The service item’s remaining time or miles will be displayed in the lower portion of the display
  2. And It is possible to browse through all condition-based service items by continually pressing the button
  3. However, this is not recommended. After pressing and holding the SET/RESET button for a second time, the bottom display will display ‘OK’ or ‘DUE.’ In the event that you press the SET/RESET button a second time, the word ‘RESET’ will appear in the lower display for that service. One more time releasing and reapplying the button will only restore the service that is now visible in the top pane. Turn off the ignition.

Oil Reset Method 2

  1. Make a single press of the start/stop button (do not turn on the engine)
  2. Maintain press-and-hold pressure on the SET/RESET button until the service indicator light illuminates
  3. To go through the service menu, continually press the SET/RESET button. Using your mouse, click and hold the SET/RESET button until the oil change interval is highlighted. As soon as the word ‘RESET’ appears, press and hold the SET/RESET button for a second time. When the message ‘OK’ displays and the new mileage displayed, the reset is complete. Turn off the ignition.

Oil Reset Method 3

  1. Turn off the ignition. Press and hold the ‘TRIP ODOMETER’ button while turning the ignition to ‘ACCESSORY 1.’ After 5 seconds, the words ‘OIL SERVICE RESET (RE)’ or ‘INSPECTION RESET (RE)’ will appear on the screen
  2. Then release the ‘TRIP ODOMETER’ button. Press and hold the button once more. After 5 seconds, the word ‘RESET’ will flash on the screen
  3. Press and hold the button. Once more, press the button. There is a new interval presented
  4. Press and hold the button again
  5. After 5 seconds, the letters ‘RE’ or ‘RESET’ will flash on the screen
  6. Release the button
  7. Turn off the ignition.
See also:  P0112 trouble code? (The answer is found)

Post navigation

You are the only person who can see this article. When it comes to BMWs, the service handbook does not include instructions on how to reset the service lights. When you bring your car into the dealership for service, the technicians will utilize this option to reset the display on your vehicle. If you are like us and like to work on your own vehicle, the procedure might be a bit difficult to understand at first. In any case, here are the instructions I’ve assembled from a variety of different sources: Most of the films for this operation are lacking in quality guidance, so I’m hoping this would be of use to everyone.

It is common for people to declare success only after multiple unsuccessful efforts.

Getting into the Service Menu

First, turn the key in the ignition. Second, without depressing the clutch or brake pedals, push the start/stop button on the steering wheel. Three, wait for the service reminder to vanish from your vehicle’s main display. 4 As soon as the service light turns off, push and hold the odometer reset button for one second.

A warning triangle will show; continue to press the button for another 2-3 seconds until the triangle vanishes and the display displays a different service icon. If you keep your finger on the button for too long, the service menu symbol will disappear and you will have to start over.

Resetting the Oil Service Warning Light

5To browse through the service menu, use the up/down toggle lever on the turn signal indicator stalk. On the main center display, find the Oil Can icon and press it to activate it. 7At the end of the turn signal indication stalk, press the BC button to activate the turn signal. The word Reset will be shown on the display underneath the oil container. Eighth, while pressing and holding the BC button for two to three seconds, an animated clock will appear on the screen. The oil service light on your dashboard has now been reset.

Get notified about new articles.

Navigate through the service menu by pressing the up/down toggle switch on the turn signal indicator shaft. On the main center display, locate the Oil Can icon and press it to activate it. 7At the end of the turn signal indication stalk, press the BC button. The word Reset will be shown on the display beneath the oil container. The clock animation will appear on screen once you press and hold the BC button for 2-3 seconds. Using the button below, you may restart your oil service light.

Reset oil service light BMW X5 – Reset service light, reset oil life, maintenance light reset

BMW X5 oil service light should be reset. The following years are included: 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012. In the BMW X5, how do you reset the oil service light? The following years are included: 2000, 2001, 2002, 2003, 2004, 2005, and 2006.

  1. The ignition key must be turned off. Turn the ignition key to the first position while pressing and holding the trip odometer reset button in the instrument cluster (the left button). In order for one of the following words to show in the display, keep the button pushed for approximately 5 seconds: ‘Oil Service’ in conjunction with ‘Reset’
  2. If the programmed minimum consumption limit has been achieved and resetting is available, the service due will be shown with the word ‘reset.’ If the word ‘reset’ is not shown, this indicates that the minimum limit has not been reached and that resetting is not feasible
  3. Press and hold the reset button once more until the word ‘Reset’ begins to flash
  4. Then release the button. While the service interval indicator is blinking, push the left button for a brief period of time to reset it. The following will appear on the screen when the new interval has been displayed: ‘Put an end to SIA’
  5. The system may only be reset once 2.5 gal (10 liters) of gasoline has been spent
  6. Otherwise, it will not work.

How to turn off the oil service light on a BMW X5 From the following years: 2006, 2007, 2008, 2009, 2010, 2011, 2012, and 2013.

  1. Insert your remote key into the key slot and push the ‘Start Stop’ button once, without placing your foot on the brake, to initiate the start/stop function. You should notice a slew of lights illuminated on the dashboard
  2. Wait for any warning lights to come on before proceeding. To turn off some warning lights, such as a low fuel warning light or a hazard warning light, you may need to click the ‘BC’ button on the end of the indicator stalk once. Hold down the black button, which is situated on the bottom left of the speedometer, for a few seconds (instrument cluster). In the midst of the speedometer, an exclamation mark will show on the screen, but continue to hold down the button until the next photo displays, at which point release the button. By pressing the black button once, you will be able to cycle through all of the photo possibilities for each service one by one. When you go to the oil service light that you want to reset, push and hold the black button until the text ‘Reset?’ is visible under the picture, then release the pressure on the button. Finally, press and hold the reset button for a second time to finalize the action. Ready

There you have it, the complete technique to reset the oil service light on a BMW X5. In the event that you wish to reset any maintenance oil light following an oil change, follow these steps: In the case of BMW automobiles, you can also reset the check engine light, airbag light, inspection key or insp faults when maintenance is required. Alternatively, any error message that occurs on the screen. Fill in the search box with the name of the vehicle for which you are looking for information, and you’ll learn how to reset other service reminders on your own.

Please let us know if our processes are being followed appropriately.

To view the entire method, please click here.

Instructions on how to reset the maintenance light and how to reset the service light on all BMW vehicles.

2018 Bmw X5: How do you reset the change oil light?

It is necessary to start the vehicle once by pushing the START/STOP button, making sure not to start the motor, in order to reset the oil light on a 2018 BMW X5. After that, push and hold the reset button, which is positioned to the left of the gauges, for at least 10 seconds to complete the process. The service indication light will begin to illuminate. The SET/RESET button allows you to navigate through the service menu and pick the oil change interval that you want. The word ‘RESET’ will appear on the screen.

  • An ‘OK’ message will appear on the screen after the operation is complete.
  • It is recommended that you change your oil and oil filter every 10,000 miles or 12 months.
  • will be celebrating her birthday on April 9, 2020.
  • Then, for 10 seconds, push and hold the set/reset button on the instrument cluster on the steering wheel.
  • You will only need to hit the star/stop button one time.
  • After that, you’ll need to press and hold the set/reset button until the service light illuminates.
  • Once the oil change interval has been highlighted, you must push and hold the set/reset button for another few seconds.

Once the reset screen shows, press and hold the set/reset button for a second time. Once everything checks out and the new mileage displays, the reset will be complete. Remove the key from the ignition.

How To Reset BMW 3 Series Oil Service Icon in Seconds!

  1. When you have the car turned off (close all doors and windows, and put the vehicle in park), turn on the ignition to the ON position. For about 10 seconds, press and hold the TRIP reset button (found on the left side of the instrument cluster) until the first service task displays in the display screen. If feasible, briefly click the TRIP button again to cycle through the service items until the oil maintenance item appears* If a reset is available, a notice stating ‘Reset Executable’ will show in the message center. When you are ready to reset, press and hold the TRIP button for 3 seconds or until the ‘Execute Reset?’ message displays. Then push and hold the TRIP button for another 3 seconds, or until the ‘Reset Successful’ message displays
  2. Then release the TRIP button. Repeat the method outlined above for any other services that need to be reset.
See also:  Alternator AC ripple test? (Suits you)

2006-2012

  1. When you have the car turned off (close all doors and windows, and put the vehicle in park), turn on the ignition to the ON position. As soon as all of the warning lights have cycled off and the warning tone has stopped blaring, press and hold the brake pedal while simultaneously pressing and holding the TRIP button until the warning triangle shows. In order to display the first service sign, you must release the TRIP button immediately after the warning triangle appears. The BC button situated on the turn signal switch may be used to cycle through the service items until the oil change icon appears on the dash display. To reset the device, press and hold the BC button for 3-5 seconds until the word ‘Reset’ shows on the screen. Then press and hold the BC button for 3-5 seconds until the display shows the time clock once again
  2. Release the BC button and repeat the process. To return to the service item screen, press and hold the button. * Repeat the preceding procedures for any other services that need to be reset. Once all of the resets have been completed, switch the car off and remove your foot from the brake pedal.

2000-2005

  1. Press and hold the TRIP or S/R button (found on the left side of the instrument cluster) for three seconds while the ignition is in the OFF position. Then, change the ignition to the ACC position. To reset your device, hold down the TRIP or S/R button until the word ‘Reset’ appears in the message center. Release the TRIP or S/R button, then press and hold it for 5 seconds, or until the ‘Reset’ message begins to flicker, before releasing the button. Press and hold the TRIP or S/R button for a few seconds to confirm the reset while the message is still blinking
  2. Then release the TRIP or S/R button. When the updated distance until the next service is required is displayed, the reset will be confirmed.

1990-2000

  1. Ensure that the key is in the OFF position. Discover and open the spherical diagnostic port located under the hood of the car
  2. Then remove the cap. Use a jumper wire (a paper clip works just as well) to connect port numbers 7 and 19 (as seen in the illustration above)
  3. Turn the vehicle’s ignition switch to the ‘ON’ position without starting the engine. Wait 10 seconds before removing the jumper wire while keeping the key in the ON position
  4. This will save time. The service indicator should be restored to its full green bars, and the warning should be removed from the screen.

1990-2001

  1. The usage of a scan tool is required by BMW in order to reset the maintenance light.

Thank you for taking the time to learn about Car How To and the Oil Reset Pro app. We hope you find these reset processes to be of assistance to you. With our mobile software Oil Reset Pro, which is available in the Apple and Google Play stores, you can always have this method, as well as the rest of the domestic, Asian, and European manual maintenance reset procedures, at your fingertips at all times. Follow the links below to get your free download from the shop right now!

BMW 4-Series: How To Reset Oil Service Light (F32/F82/G22)

What are you up to these days, dude? The oil service light on this BMW 4-Series F32/F82/G22 will be reset today on shady cars, and it will be the first of many. In other words, while I am showing this method on our 2012 435i with the N55 engine, this process is applicable to virtually every BMW sedan or coupe. I did, in fact, replace the oil on this vehicle. The only reason I don’t reset their oil indication is since I don’t rely on the character to inform me when to change my oil. But now I’m going to walk you through the process I used to do it.

How To Reset Oil Service Light On BMW 4-Series (F32/F82/G22)

Warning! Please make a note of the make and model of your car. This guide will work for the BMW4-Series F32/F82/G22 cars from the years 2014, 2015, 2016, 2017, 2018, 2019, 2020, and 2021. (428i 435i 420i 430i M440i models).

BMW F32/F82 (428i 435i)

The time required is three minutes. Using the BMW 428i as an example, I’ll teach you how to reset the service light in this chapter. I believe this is true across the board for the whole four-series slate. So allow me to demonstrate how to proceed and complete this task.

  1. Start the engine by turning the key in the ignition. To start the car, press the ignition button once while your foot is still on the brake. Continue to hold down theTRIPbutton. Afterwards, we’ll navigate our way to the left side of the dashboard and hold down the TRIPbutton until we see the Service reset menu
  2. Navigate to the ENGINE OIL section of the screen. You’ll want to press theTRIPbutton to scroll down to the Engine Oil section. Press and hold theTRIPbutton for a few seconds. To reset this, I’m going to go ahead and hold down theTRIPDOWN button until it says Reset
  3. One more press of theTRIPbutton will be required. Once I’ve done that, I’m going to hit it one more time, and it’ll say ‘reset in progress,’ and then it’ll say ‘reset successful.’

BMW G22 (420i 430i M440i)

  • To begin, insert the key into the ignition and quickly press theSTARTbutton three times in rapid succession. Then, as soon as you see theDiagnostic Mode Activemessage, all of the lights on the dashboard will illuminate. Next, press and hold the BCbutton at the end of the left stalk for a few seconds.
  • From there, you may use the BCbutton to go through the menu until you reach theENGINE OIL option. Now press and hold the BCbutton once more until you see the words ‘reset question mark’ appear on the screen. Finally, press and hold the BCbutton once more until the bar appears and the reset process begins
  • Then release the button.

Now that I’ve changed the oil, the automobile is aware of the fact and will not remind me to replace the oil again anytime soon. So it brings us to the conclusion of this section. I hope you found the information to be useful. If you did, please let us know by leaving a comment below. I appreciate you taking the time to read this. So, thank you very much, and have a wonderful day.

One more time for me; How to reset after oil change

Okay, so I’m not a complete newbie when it comes to BMWs. I’ve owned several of these throughout the years, and I currently have four distinct models in my collection. I followed the directions supplied, which were pretty similar to those for other BMW platforms, I watched the YouTube video mentioned above and a few others, and yep, the doors are closed, the seatbelt is fastened, and so on and so forth. Simply said, I want to be clear. Nevertheless, for some weird reason, following the instructions stated, or doing what I do for my other BMWs, does not apply to the f25.

I can undo or reset oil change intervals, and so on, using my laptop, but it’s inconvenient to have to do so.

I’ve done quite a few modifications to my automobiles as a result of these fantastic forums and their wonderful people.

See also:  AC stops cooling Dodge Neon? (Question)

This is the difficulty I’m having, as previously said, and I’m not sure why this is happening.

It’s likely that there are other people who either didn’t bother anymore to follow the approach stated in the previous section, or who figured out what they were doing incorrectly. I’m sure there’s some little element I’m overlooking.

Oil Change Light Reset BMW M5 2014 2015

After every oil change, the Oil Change Light Reset BMW M5 2014 2015 will need to be done on the vehicle. If the system is not correctly reset, it will be unable to track when your next oil change is necessary. The technique for resetting the oil change light on a BMW M5 from 2014 to 2015 is outlined below. When you replace your oil, follow the instructions outlined below to reset the oil life monitor.

Oil Change Light Reset BMW M5 2014 2015 Procedure

  1. Make a single press of the start/stop button (do not turn on the engine)
  2. Maintain press-and-hold pressure on the SET/RESET button until the service indicator light illuminates
  3. To go through the service menu, continually press the SET/RESET button. Using your mouse, click and hold the SET/RESET button until the oil change interval is highlighted. As soon as the word ‘RESET’ appears, press and hold the SET/RESET button for a second time. When the message ‘OK’ displays and the new mileage displayed, the reset is complete.

Oil Viscosity and Capacity

When the engine oil and filter are changed, the 4.4 Turbo liter engine has a capacity of roughly 9 quarts (8.5 liters) of 5W-40 oil in it.

Not Working?

If the oil change light reset procedure for the BMW M5 2014 2015 does not work to reset your oil life monitor, double-check that you are following each step exactly and in the order specified in the Oil Change Light Reset BMW M5 2014 2015 procedure above. If the procedure for the BMW M5 2014 2015 does not work, double-check that you are following each step exactly and in the order specified in the procedure for the BMW M5 2014 2015. If this is not the oil life monitor reset technique for your car, then searchHERE for the correct oil life monitor reset procedure for your vehicle.

Oil Life Monitor Reset Procedure Frequently Asked Questions

If you are still having difficulties, please go to theOil Life Monitor Reset Procedure Frequently Asked Questions (FAQ) page for further information and assistance.

Notice

Because there is such a vast variety of car types and models, this is generic information that should not be interpreted as unique to any particular vehicle. To ensure that you have the right specs and repair methods for your car, please check the vehicle manufacturer. This information is only intended to be used as a general guideline.

Reset oil life monitor BMW

For BMW model years 2006-2010, start with this manual procedure to see if it helps. On many late-model BMW automobiles, the oil life monitor, however, cannot be reset manually due to software limitations. It is necessary to utilize a reset tool. Take a look at the resources listed below. 1. Press the START/STOP button or turn the ignition key one click to the ON position. 2. For 10 seconds, press and hold the Instrument Cluster Set/Reset button on your keyboard. 3. An symbol for a service item will be illuminated on the upper display screen.

  1. Continue to press the button until the icon you desire appears on the screen.
  2. 5.
  3. One more time releasing and reapplying the button will only restore the service that is now visible in the top pane.
  4. Start the engine after turning off the ignition to ensure that the indication has been reset.
  5. Turn the ignition to the ON position but do not start the engine.
  6. Hold down the RESET button on the top left side of the instrument cluster for ten seconds to bring up a four-line menu on the speedometer display.
  7. 3.
  8. 5.

6. Press and hold the RESET button for a few seconds more. 7. Turn off the ignition and restart the vehicle to ensure that the indicator has been reset. 8. Rick Muscoplat was born in the year 2012. Rick Muscoplat posted a blog entry on

BMW X5 and BMW X6 oil reset service light indicator oil life maintenance

What is the best way to oil reset the maintenance light? The BMW X5 and BMW X6 maintenance light, the BMW X5 and BMW X6 oil reset service light, and the BMW X5 and BMW X6 oil reset service light indicator are all for the years 2000 to 2013, with the exception of the years 2001 to 2002. Resetting the maintenance light may be accomplished manually by pressing a button on the dashboard of the vehicle.

For BMW X5 and BMW X6 years 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013 models the oil reset maintenance light system can also be reset as follows:

  1. When you have the car turned off (close all doors and windows, and put the vehicle in park), turn on the ignition to the ON position. To begin, press and hold the TRIP reset button for about 10 seconds, or until the first service task displays on the display. Remove your finger from the button and press it repeatedly to pick the preferred maintenance item to be reset (the oil can shows that the oil needs to be changed). If you want to reset the device, press and hold the TRIP button for 3-5 seconds, or until the display says ‘Reset?’ Remove your finger from the button, then press and hold it for another 3 seconds, or until the display says ‘—-,’ and then release the button. Repeat the method outlined above for any other services that need to be reset, such as brakes, spark plugs, or filters. To verify that the reset was successful, turn the ignition to the OFF position and then back on.

BMW X5 and BMW X6 oil reset service light indicator

This reset should be performed after the engine oil and filter have been replaced in accordance with the technical criteria related to the manufacturer. Resetting the engine without changing the oil causes early engine wear and causes major difficulties with the operation of the engine and its components. You should not start your vehicle if the oil change indicator message is illuminated. This indicates that the oil change indication system was not reset. Repeat this method as many times as necessary.

Cookies are used on this website to enhance your browsing experience.

Accept More information can be found at

Reset E39 E38 E53 X5 oil service inspection light

The following process is only applicable to BMW E39, E38, and E53 X5 cars with a build date beginning on or after September 1, 2000. The oil service / inspection lights on early model E39, E38, and E53 X5 vehicles must be reset using a separate procedure. After completing an oil change, the oil service / inspection light on the BMW E39, E38, and E53 X5 must be turned off and on again. Once the computer has been reset, it will begin counting down from 15,000 miles until the next oil change. The reset operation is straightforward and does not need the use of any specialized BMW tools or the assistance of a BMW store in any way.

What are the steps?

  • While holding the trip odometer button down, turn the ignition key to the first position (KLR) and push and hold the bottom left button on the instrument cluster. IMPORTANT: DO NOT MOVE TO THE SECOND POSITION
  • If you do, remove the key and start over
  • Keep the trip odometer button pressed for approximately 5 seconds until one of the following words appears in the display: ‘OIL SERVICE’ or ‘INSPECTION’ or ‘RESET SIA:’ illuminates
  • Release the trip odometer button and press and hold it until ‘RESET’ flashes on the display and release your finger
  • While the display is flashing

Only when 2.5 gallons (10 liters) of gasoline have been spent, or after the vehicle has traveled 50 to 75 miles, can the system be reset once more.

Other BMW model oil service inspection light reset procedures:

Leave a Comment

Your email address will not be published. Required fields are marked *