Acura Oil Light Reset procedure? (Solution)

Professional recommendations

Press and hold the SEL/RESET button for at least ten seconds or until the remaining oil life is displayed. Below the OIL LIFE RESET, you will see the RESET option. Select the RESET by pressing the Up/Down button on the steering wheel. Next, press the SEL/RESET button to reset the engine oil reminder.

How do you reset the oil life on a Acura RDX?

To reset the oil light in an acura rdx you need to turn the vehicle on with the engine off, go to select/reset until engine oil life displayed, then hold down the button for 10 seconds.

How do you reset the oil life on a 2012 Acura?

To reset the 2012 Acura TL maintenance light, please follow these instructions:

  1. Turn the ignition to (II) – do not start the engine.
  2. Press the SEL/RESET button on the steering wheel repeatedly until engine oil life is displayed.
  3. Press and hold the SEL/RESET button for more than 10 seconds.

How do you reset the oil light on a 2017 Acura RDX?

How To Reset Oil Life/Maintenance Light On Acura RDX

  1. Turn on the ignition without starting the engine. With foot off the brake push the START button twice to get the dash all lit up.
  2. Go to the VEHICLE SETTINGS or CUSTOMIZE SETTINGS.
  3. Scroll and select MAINTENANCE INFO.
  4. Select RESET.

How do you reset the oil light on a 2014 Acura RDX?

To reset the 2014 acura rdx maintenance light, turn the ignition on (ii)-do not start the engine. Click the sel / reset button on the steering wheel repeatedly until the engine’s oil life is clear. Click and hold the sel button for more than ten seconds.

Reset oil service light Acura TL – Reset service light, reset oil life, maintenance light reset

The following years are covered: 1995, 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004; 2005; 2006; 2007, 2008; 2009; 2010. Reset oil service light Acura TL. Acura TL oil service light reset for the following years: 1995, 1996, 1997, and 1998.

  1. By putting the key into the slot below the coloured indication, the indicator may be reset.

Reset the oil service light on your Acura TL from the year 1999 or 2000.

  1. After you have turned off your ignition, press and hold the SELECT AND RESET buttons on your instrument panel for several seconds. Do not start the engine by turning the ignition to position (II). Hold down the SELECT and RESET buttons for 10 seconds or until the indicator resets. Check to see whether the indication has been reset by turning off the ignition and restarting the vehicle.

Acura TL oil service light reset for the following years: 2001, 2002, and 2003.

  1. After you have turned off your ignition, press and hold the SELECT AND RESET buttons on your instrument panel for several seconds. Set the ignition to the second position (II)
  2. To keep holding buttons, keep pressing them until the indication vanishes. Check to see whether the indication has been reset by turning off the ignition and restarting the vehicle.

Acura TL oil service light reset for the following years: 2004, 2005.

  1. Do not start the engine by turning the ignition to (II). Continue to press the SELECT/RESET button until the oil life indicator appears. For 10 seconds, press and hold the SELECT/RESET button on your keyboard. Until the information displayed on the screen requests confirmation
  2. To reset the display, press the Choose/RESET button to select OK and then release the button. Check to see whether the indication has been reset by turning off the ignition and restarting the vehicle.

Acura TL oil service light reset for the following years: 2006, 2007, 2008, 2009, and 2010.

  1. Don’t start the engine by turning the ignition to position (II). Repeatedly press the SEL/RESET button on the steering wheel until the engine oil life indicator appears
  2. More than 10 seconds should be spent pressing and holding the SEL/RESET button. This will be displayed on the multi-information display along with the remaining engine oil life reset mode. By pushing the INFO button twice, choose RESET, and then press the SEL/RESET button to clear the engine oil life display and start over. There will be no more maintenance item codes, and the engine oil life will be reset to 100
  3. After you have turned off the ignition and started the engine, check to see if the indication has been reset. Instead of an ignition switch, models equipped with the keyless entry system feature an engine start/stop button. In the absence of an engine start, pressing the start/stop button once is the equivalent of ignition (II).

If you’re looking for the placement of Acura TL filters, go no further than this! That is the whole technique for resetting the oil service light on an Acura TL. Following an oil change. For Acura vehicles, you may reset any maintenance oil light by pressing the button below. Alternatively, any error message that occurs on the screen. Fill in the search box with the name of the vehicle for which you are looking for information, and you’ll learn how to reset other service reminders on your own.

Send us a remark if you believe our methods are proper or if you have something to contribute; we value all of our customers’ perspectives.

What is the procedure for resetting the oil light indicator?

Reset Acura Engine Oil Life / Maintenance Minder

2013-15 Eneine Oil Life/Maintenance Minder – Procedure 6

MDX

2007-13 Engine Oil Life/Maintenance Minder – Procedure 1
2014-15 Engine Oil Life/Maintenance Minder – Procedure 7

RDX

2007-08 Engine Oil Life/Maintenance Minder – Procedure 3
2009-12 Engine Oil Life/Maintenance Minder – Procedure 1
2013-15 Engine Oil Life/Maintenance Minder – Procedure 6

RL

2005 Engine Oil Life/Maintenance Minder – Procedure 5
2006 Eneine Oil Life/Maintenance Minder – Procedure 2
2007-10 Engine Oil Life/Maintenance Minder – Procedure 4
2011-12 Engine Oil Life/Maintenance Minder – Procedure 1

RLX

2014-15 Engine Oil Life/Maintenance Minder – Procedure 7

TL

2004-06 Engine Oil Life/Maintenance Minder – Procedure 2
2007-08 Engine Oil Life/Maintenance Minder – Procedure 1
2009-10 Engine Oil Life/Maintenance Minder – Procedure 4
2011-14 Engine Oil Life/Maintenance Minder – Procedure 1

TSX

2006 Engine Oil Life/Maintenance Minder – Procedure 1
2007-10 Engine Oil Life/Maintenance Minder – Procedure 4
2011-13 Engine Oil Life/Maintenance Minder – Procedure 6
2014 Engine Oil Life/Maintenance Minder – Procedure 1

ZDX

2010-13 Engine Oil Life/Maintenance Minder – Procedure 1

ENGINE OIL LIFE/MAINTENANCE MINDER – PROCEDURE 1

1. Insert the ignition key into the ON (II) position. *Please keep in mind that for models equipped with the keyless access system, the engine start/stop button replaces the traditional ignition switch. ON Mode is the equivalent of the word ‘ON’ (II) WARNING: If the engine oil life is not displayed on your RDX’s multi-information display, press the SEL/RESET button on your steering wheel continuously until the screen is completely blank and only the SH-AWD and tire pressure are displayed. Press and hold the SEL/RESET button repeatedly until the engine oil life indicator appears.

  1. Press and hold the SEL/RESET button for more than ten seconds to restart the computer.
  2. Please make sure that any maintenance item(s) that require servicing are completed before resetting the display if the engine oil life is greater than 15 percent at the time of the reset.
  3. The maintenance item code(s) will be removed from the system, and the engine oil life will be reset to 100 minutes.
  4. To cancel the oil life reset mode, press the CANCEL key on your keyboard.

ENGINE OIL LIFE/MAINTENANCE MINDER – PROCEDURE 2

1. Turn the ignition switch to the ‘ON’ position (II). 2. Press the SELECT/RESET button repeatedly until the oil life is displayed (if it is greater than 15 percent) or the maintenance notice is displayed (whichever comes first) (if oil life is less than 15 percent ). NOTE: If you attempt to reset the display when the oil life is greater than 15 percent, the maintenance notice ‘SERVICE DUE SOON’ will be shown on the screen. Before attempting to reset this display, double-check that any maintenance tasks that require attention have been completed.

3) Press and hold the SELECT/RESET button for ten seconds, or until you see the maintenance message or the phrase ‘MAINTENANCE RESET.’ If the maintenance message is displayed, press and hold the SELECT/RESET button for 10 seconds, or until the message ‘MAINTENANCE RESET’ is displayed.

  • When you want to reset the display, click the SELECT/RESET button until you see ‘OK.’ After that, every time the ignition switch is switched to the ‘ON’ position, the display will read ‘OIL LIFE 100 percent.’ If you do not wish to reset the display, hit the INFO button on the right side of the screen and select ‘Cancel.’ Please keep in mind that if the needed service is conducted but the display is not reset, or if the display is reset but the service is not performed, the system will not reflect the correct maintenance levels for the system. Because there will be no record of when maintenance is required, this might result in major mechanical difficulties. ‘SERVICE PAST DUE’ will show if the recommended maintenance service is not completed and there is less than 0 percent remaining engine oil life. If this occurs, immediately schedule a maintenance appointment and remember to reset the display as previously described. It is recommended that you replace the engine oil every year if the message ‘SERVICE DUE NOW’ does not show more than 12 months after the display has been reset

ENGINE OIL LIFE/MAINTENANCE MINDER – PROCEDURE 3

1. Insert the ignition key into the ON (II) position. 2. Continue to turn the SEL/RESET knob on the steering wheel until the engine oil life indicator appears. 3. For approximately 10 seconds, press and hold the SEL/RESET knob. On the multi-information display, the remaining engine oil life reset mode will be displayed as well. Select RESET by pushing the INFO (up or down) button, followed by the SEL/RESET button to clear the engine oil life display. The maintenance item code(s) will be removed from the system, and the engine oil life will be reset to 100 minutes.

Without Technology Package

1. Insert the ignition key into the ON (II) position. 2. Continue to press the SELECT/RESET knob until the engine oil life indicator is shown. 3. For about 10 seconds, press and hold the SELECT/RESET knob. The engine oil life and maintenance item code(s) will be illuminated when the engine is running. 4. Continue to hold down the SELECT/RESET knob for another 5 seconds. The maintenance item code(s) will be removed from the system, and the engine oil life will be reset to ‘100.’

ENGINE OIL LIFE/MAINTENANCE MINDER – PROCEDURE 4

1. Insert the ignition key into the ON (II) position. 2. If the engine oil life minder does not appear to be shown, push the SEL/RESET button on the steering wheel repeatedly until the oil life minder appears. For more than 10 seconds, hold down the SEL/RESET button. On the multi-information display, the remaining engine oil life reset mode will be presented in real time. 4. Select RESET by using the UP or DOWN arrow buttons on the steering wheel, then push the SEL/RESET button. The maintenance item code(s) will be removed from the system, and the engine oil life will be reset to 100 minutes.

To cancel the resetting of the oil life reset mode, use the UP or DOWN arrow buttons to choose CANCEL, then hit the SEL/RESET button on the control panel’s keypad.

ENGINE OIL LIFE/MAINTENANCE MINDER – PROCEDURE 5

1. Insert the ignition key into the ON (II) position. 2. If the oil life minder does not appear to be shown, continuously push the SEL/RESET button on the steering wheel until it appears. 3. Press and hold the SEL/RESET button on the steering wheel for ten seconds to restart the vehicle. On the multi-information display, the remaining engine oil life reset mode will be presented in real time. Using the UP or DOWN arrows on your steering wheel, pick RESET from the display, and then press the SEL/RESET button to restart the engine oil life indicator.

To cancel the resetting of the oil life, click the UP or DOWN button on the steering wheel to choose CANCEL on the display, and then press the SEL/RESET button on the steering wheel again.

ENGINE OIL LIFE/MAINTENANCE MINDER – PROCEDURE 6

1. Turn on the power mode switch. 2. To show CUSTOMIZE SETTINGS on the multi-information display, use the UP or DOWN buttons on the steering wheel (right side) (center of instrument cluster). 3. Select CUSTOMIZE SETTINGS by pressing the SEL/RESET button three times. Press the UP or DOWN buttons on the steering wheel to bring up the MAINTENANCE INFO display. 5. To make a selection, press the SEL/RESET button. Using the UP or DOWN arrows on your steering wheel, pick RESET from the display, and then press the SEL/RESET button to restart the engine oil life indicator.

In order to cancel the oil life reset, click the UP or the DOWN button on the steering wheel to choose CANCEL on the display, and then push the SEL/RESET button on the instrument panel.

ENGINE OIL LIFE/MAINTENANCE MINDER – PROCEDURE 7

1. Turn on the power mode by pressing the power button. 2. Select Vehicle SettingsMaintenance Information from the multi-function steering-wheel control (located on the right side of the steering wheel). 3. Depress the multi-function steering-wheel control button on the steering wheel. On the MID, the oil life reset mode is indicated by a red arrow. With the multi-function steering-wheel controls, choose Reset and then press the multi-function steering wheel control. The maintenance items that were presented are no longer visible, and the engine oil life display returns to 100 percent.

Post navigation

The Oil Change Light Reset Acura RDX 2021 procedure will need to be carried out after each oil change in the vehicle. If the system is not correctly reset, it will be unable to track when your next oil change is necessary. The following is the procedure for the Acura RDX in 2021. When you replace your oil, follow the instructions outlined below to reset the oil life monitor.

Oil Change Light Reset Acura RDX 2021 Procedure

  1. Make sure that the power mode is turned on (but do not start the engine). Continue to rotate the selector wheel to the right until the content is shown. Then, using the right selecting wheel, scroll down until the Maintenance screen appears. Enter the reset mode by pressing and holding the right selection wheel for about 10 seconds. Rotate the right selector wheel to pick a maintenance item to be reset, or to select All Due Items to be reset all maintenance items. (Alternatively, you can push the right selection wheel to the left to bring the procedure to a close.) To reset the currently chosen item, press the right selecting wheel. Step 4 should be repeated for any additional things you desire to reset. After you have turned off the ignition and started the engine, check to see if the indication has been reset.

Not Working?

Make certain that you are following each of the stages in the technique above exactly and in the sequence stated in the procedure above if the oil change light reset procedure does not work to reset your oil life monitor. If this is not the oil life monitor reset technique for your car, then searchHERE for the correct oil life monitor reset procedure for your vehicle.

Oil Life Monitor Reset Procedure Frequently Asked Questions

If you are still having difficulties, please go to theOil Life Monitor Reset Procedure Frequently Asked Questions (FAQ) page for further information and assistance.

Notice

Because there is such a vast variety of car types and models, this is generic information that should not be interpreted as unique to any particular vehicle. To ensure that you have the right specs and repair methods for your car, please check the vehicle manufacturer. This information is only intended to be used as a general guideline.

Oil Change Light Reset Acura TL 2007 2008 2011 2012 2013 2014

After every oil change, you will need to manually reset the oil change light on your Acura TL 2007 2008 2011 2012 2013 2014 by pressing the button on the instrument panel. If the system is not correctly reset, it will be unable to determine when your next oil change is necessary.

  1. Make that the ignition switch is in the ON (II) position. To show the engine oil life indicator, press and release the SEL/RESET button repeatedly until the indicator is displayed. More than 10 seconds should be spent pressing and holding the SEL/RESET button. During the reset mode, the remaining engine oil life will be displayed on the multi-information display. Hit the UP or DOWN button repeatedly until the RESET indicator is displayed, then press the SEL/RESET button to restart the computer. There will be no more maintenance item codes, and the engine oil life will be reset to 100
  2. If you wish to cancel the oil life reset mode, press the CANCEL button.

*Please keep in mind that for models equipped with the keyless access system, the engine start/stop button replaces the traditional ignition switch. ON Mode is the equivalent of the word ‘ON’ (II) WARNING: If the engine oil life is not displayed on your RDX’s multi-information display, press the SEL/RESET button on your steering wheel continuously until the screen is completely blank and only the SH-AWD and tire pressure are displayed. Please make sure that any maintenance item(s) that require servicing are completed before resetting the display if the engine oil life is greater than 15 percent at the time of the reset.

If this process does not work for your Acura TL 2007 2008 2011 2012 2013 2014, please see ourFrequently Asked QuestionspageHERE for further assistance. The material on this site is not meant to be used as repair advice, and we are not liable for any actions you take in relation to any automobile.

2004-2014 Acura TL Service Minder Oil Life Light Reset Procedure

Hello there, Brother. May peace be with you. Today, I’ll demonstrate how to reset the Acura TL’s service reminder light, often known as the oil life monitor. So when your oil life is at 5 percent, when it reaches 15 percent, you’ll receive this wrench, and it will say Service due soon, and then it will say Service due now, and so on. Now, we’ve reached the end of our journey with this car, and the B13 service indicator has shown. Each letter and number on the invoice shows the services that are payable.

So let us begin the process of resetting the system.

2004-2006 Acura TL

  • Select/Reset/Info buttons may be found on the right side of the instrument cluster, if you look down on the right side of the instrument cluster. Turn the ignition switch to position 2. As a result, you must repeatedly click theINFObutton until you reach the OIL LIFE or Service reminder screen.
  • After that, you’ll press and hold theSELECT/RESETbutton for around 10 to 15 seconds, after which a little message will appear with the choice to reset or cancel the selection
  • Consequently, you just hit theSELECT/RESETbutton to reseet it

2007-2008 Acura TL

The time required is three minutes. We’re going to reset the oil life on the old Acura TL in this part, so buckle up and get ready. What we are going to do is as follows:

  1. Start the engine by turning on the ignition without starting the engine. Because this Acura has a START button, you may just press the start button twice without having to use the brake. The OIL LIFE or Service reminder screens will appear. To view your oil life or service reminder, keep pushing the UP button until you see the screen. Continue to hold down the SEL/RESET button. Once you’ve done that, press and hold the SEL/RESET button for slightly over 10 seconds, or until you reach the Reset menu
  2. SelectRESETAfter that, press the UP button to bring the RESET area to the forefront, and then press the SEL/RESET button to confirm your selection

2009-2014 Acura TL

  • Simply pressing theSTARTbutton twice while your foot is off the brake will imitate position two. Simply press theSEL/RESETbutton till you receive your actualOIL LIFE
  • This is all that is required. Once you’ve arrived, press and hold the SEL/RESET button for 10 seconds, and a menu will appear, from which you may choose to either reset or cancel your session. To reset it, you must first choose the RESET option by pressing the UP button on your keyboard, and then press the SEL/RESET button to confirm your selection.

That’s all there is to it, guys. You’ll see oil life 100 percent as you walk through the various informational elements, which means you’re good to go until your next oil change. If you have any additional automobiles you’d want me to cover in the reset processes, please let me know in the comments section below and I’ll do my best to cover them next. Thank you for your time, and please enjoy the remainder of your day.

How To Reset Acura TL Maint Req’d Light in Seconds!

  1. Set the ignition switch to the ON (II) position
  2. Turn on the vehicle. Customize Settings- in the display may be selected by pressing the SEL/RESET button on the steering wheel after pressing the arrow buttons on the steering wheel. Using the arrow buttons, choose -Maintenance Info- and then hit the SEL/RESET button to confirm your selection. Use the arrow buttons to choose -Reset-, then click the SEL/RESET button to confirm your selection. The maintenance item code(s) will be cleared, and the engine oil life will be restored to its original value.

2009-2014

  1. Set the ignition switch to the ON (II) position
  2. Turn on the vehicle. If the engine oil life indicator does not appear to be shown, push the SEL/RESET button on the steering wheel repeatedly until it does. For more than 10 seconds, press and hold the SEL/RESET button on the steering wheel, then release it. This will be displayed on the multi-information display along with the remaining engine oil life reset mode. Select Reset by selecting the INFO (up and down arrow icons) button, then push the SEL/RESET button to reset the engine oil life display
  3. This is accomplished by pressing the SEL/RESET button twice. There will be no more maintenance item codes, and the engine oil life will be reset to 100 percent.

2007-2008

  1. Set the ignition switch to the ON (II) position
  2. Turn on the vehicle. In order to see the engine oil life, press the INFO (up and down arrow icons) button until it appears. For more than 10 seconds, press and hold the SEL/RESET button on the steering wheel, then release it. The display will prompt you to confirm your selection. To choose ‘OK,’ press the SEL/RESET button on your keyboard.

2004-2006

  1. Set the ignition switch to the ON (II) position
  2. Turn on the vehicle. Continue to press and hold the SELECT/RESET button for 10 seconds or until you see the maintenance message or the words ‘Maintenance Reset’ on the screen. Remove your finger from the SELECT/RESET button, then press and hold it for another 10 seconds, or until you see ‘Maintenance Reset’ on the screen. To reset the display, press the Pick/RESET button and select ‘OK’ from the drop-down menu. The next time the ignition switch is turned on, the message ‘OIL LIFE100%’ will appear on the screen.

Thank you for taking the time to learn about Car How To and the Oil Reset Pro app. We hope you find these reset processes to be of assistance to you. With our mobile software Oil Reset Pro, which is available in the Apple and Google Play stores, you can always have this method, as well as the rest of the domestic, Asian, and European manual maintenance reset procedures, at your fingertips at all times. Follow the links below to get your free download from the shop right now!

Acura Oil Light Reset procedure

The following is the technique to follow in order to reset the oil light on Acura automobiles. To start the engine, turn the ignition to position II, but do not turn the key. Repeatedly press the SEL/RESET button on the steering wheel until the engine oil life indicator is shown. More than 10 seconds should be spent pressing and holding the SEL/RESET button. The reset mode for the ‘remaining
engine oil life’ will be displayed on the multi-information display. By tapping the INFO up/down button, select RESET from the drop-down menu.

In this case, the engine oil life will be reset to 100.

It should be noted that models equipped with a keyless entry system feature an engine start/stop button in place of an ignition button.

Only once should be pressed on the start/stop button to avoid starting the engine. For the sake of this comparison, position II on the ignition switch is identical to position I.

Reset oil light for 2006 and older Acura vehicles

To turn the key off, turn it to the off position. Maintaining pressure on the SELECT and RESET buttons on the instrument panel while rotating the ignition switch to position II WITHOUT beginning to operate the engine is recommended. Hold down the SELECT and RESET buttons at the same time for about 10 seconds, or until the indicator resets. Remove the key from the ignition. After that, start the engine to ensure that the indication has been reset properly. Rick Muscoplat has a new year’s resolution.

How To Reset Maintenance Minder Oil Change Light on Acura RL (2005-2012)

On the Acura RL (2005-2012), here’s how to reset the Maintenance Minder oil change light. A full-size car, the Acura RL was manufactured by the Japanese firm Acura between 1996 and 2012. The Acura RL took over for the Acura Legend in the lineup, and it was replaced by the Acura RLX the following year. ‘Refined Luxury’ is the meaning of the term RL. Known internally as the ‘KB1,’ the new generation of automobiles made their debut at the end of 2004 as the 2005 model year. A complex all-wheel-drive system, known as ‘Super Controlled All-Wheel Drive,’ was installed in the automobile, despite the fact that the V8 engine never made an appearance under the hood (SH-AWD).

Did you notice that your 2005 206, 2007 2008, 2009, 2010, 2011, 2012 Acura RL’s maintenance service warning light came on every time you turned the key in the ignition?

Please remember to re-set the service interval after you have completed the service.

  1. Start the engine by turning on the ignition without starting the engine. You may start your car without using the keys if it has keyless entry
  2. Simply push the ENGINE START STOP button twice while keeping the brake pedal down. Continue to press the SEL/RESET button until the engine oil life indicator shows on the display. The button is positioned on the steering wheel
  3. It has a red background. To enter reset mode, press and hold the SEL/RESET button until the message ‘reset mode’ shows on the display. More than 10 seconds should be spent pressing the SEL/RESET button. To reset the oil life, select RESET from the drop-down menu. Done

This tutorial is based on the owner’s handbook for the Acura RL. This method should be used to the second generation of Acura RL vehicles as well (2006 2007 2008 2009 2010 2011 2012 2013 2014 2015 2016 2017 2018 2019 2020 2021 model years). It is hoped that the article How to Reset the Maintenance Minder and Oil Change Light on an Acura RL (2005-2012) will help you to resolve your issue. Wishing you the best of luck!

Maintenance Reminder FAQS

Q:Can you tell me how the Acura Maintenance Minder operates? In the information display, the maintenance minder system indicates the remaining engine oil life, which alerts the owner when it is time to replenish the engine oil and perform routine engine maintenance. In the owner’s handbook, there is no longer a timetable for routine maintenance. The system displays engine oil life as a percentage, which decreases over time as the car accumulates more kilometers on the odometer. It starts off at 100 percent with new engine oil and gradually decreases to zero percent, showing that the oil life has expired.

  • As a result of the engine’s operating circumstances, the system calculates the remaining oil life (both normal and severe).
  • The on-board computer is located in the instrument cluster.
  • A:The Acura Maintenance Minder is quite simple to operate.
  • It will turn on the Maintenance Minder light for you when the on-board computer deems that your vehicle has 15 percent of its life left and it has reached that threshold.

To return to the odometer/tripometer display, just depress the Select/Reset knob until the display is restored. Following is a chart that will illustrate when each type of service is required:

Oil Life % Message What to do
15% Service Due Soon Plan to take your vehicle in for service.
5% Service Due Now Take your vehicle in now for maintenance.
0% Service Past Due Service is overdue.Take your vehicle in now.

When the Maintenance Minder’s remaining life is reduced to zero percent, what happens to it is a common question. A:If you do not do the suggested maintenance, the mileage displayed on the dashboard will begin to decrement. This represents the number of miles the vehicle has traveled since it was last serviced. Occasionally, a letter or a number is presented beside the and the % of life left to live – what do these represent? A:All of the maintenance items displayed on the screen are in code.

Your car will always be due for a main code, and it may also be due for a sub-code at some point in the future.

Main Code What it means:
A Replace just the engine oil
B Replace the engine oil, oil filter, rotate the tires, inspect the front and rear brakes, check the parking brake adjustment, and inspect other items specific to your vehicle
Sub Code What it means:
1 Rotate the Tires
2 Replace the air cleaner element, check the drive belt, and replace the dust and pollen filter
3 Replace the transmission fluid and transfer fluid (if equipped)
4 Replace the timing belt (if equipped), inspect the water pump, and inspect valve clearance
5 Replace the engine coolant
6 Replace the rear differential fluid (if equipped)

Q:Why is it necessary to have a Main-code at all times? A:When the main-codes are triggered, the sub-codes are activated as a result. Main-codes are USER-SPECIFIC, and they are triggered based on the operational circumstances of the vehicle in question. The system has been intended to provide the greatest amount of client convenience. Q:Why is it that there is only a Sub-code on occasion? A:These items require maintenance on a time/mileage basis, similar to the maintenance plans that were in place in the past.

  • In the case of tire rotation, for example, if the tire rotation is generally performed at 7,500 miles but the oil life expires at 6,000 miles, the system will advance the tire rotation up to 6,000 miles.
  • Regardless of the situation, the maintenance item code A1 would be displayed on the information display.
  • A:It will differ from person to person.
  • For example, light highway driving in a warm area will lengthen the time between needed maintenance visits by a significant amount.
  • Short-distance travel in a cold region, on the other hand, may cause the maintenance period to be reduced to 3,000 miles or less.
  • The vast majority of people maintain regular driving behaviors, which indicates that their mileage between maintenance visits will be stable as well.
  • Q:With my Honda truck, the first time the Acura Maintenance Minder came on was at 7,700 miles with an A1.

Why did I only get 4,300 miles out of my car?

It is estimated that the first 7,700 miles were logged largely on highways in warm weather – conditions that are advantageous to oil longevity.

In addition to being extremely clever, the Acura Maintenance Minder system analyzes engine load to assess oil consumption.

Q:I change my oil every 3,000 miles on my car’s engine.

A:It is advised that you adhere to the Acura Maintenance Minder’s recommendations.

The following are some of the ways that the system will benefit you and the environment: There will be no needless waste of natural resources (oil), and there will be no needless hazardous materials that will necessitate the correct disposal of hazardous waste (oil and filters).

My oil change station suggests that I replace my oil every 3,000 miles, which I believe to be accurate.

A:The 3,000-mile oil change is a fairly cautious approach to car maintenance that dates back to 1968 and is still used today.

These innovations, in conjunction with the Acura Maintenance Minder, allow you to lengthen maintenance intervals without putting your engine at danger of harming it.

Q:Normally, my Acura Maintenance Minder light illuminates after 6,500 miles, but I have only 4,500 miles on the clock and am leaving for vacation.

What should I do in this situation?

Even if you decide to have maintenance performed sooner rather than later, be sure to reset the Maintenance Minder light, as this will ensure that the main codes as well as the subcodes remain in sync.

I have decided to just have a ‘A’ service completed.

A:Yes.

The main and subcodes will go out of sync, and the Maintenance Minder will be unable to accurately estimate when maintenance will be necessary.

Is it necessary to reset the light?

Once your oil has been changed, it is critical that you follow all Acura Maintenance Minder guidelines and that the indicator on your dashboard is turned off.

Should I anticipate to go a greater distance before the Acura Maintenance Minder alerts me that it is time to replace the oil?

In order to determine your vehicle’s maintenance requirements, the Acura Maintenance Minder looks at the oil recommendation made by the Acura experts who developed your engine.

I have a Maintenance Minder Acura that my husband and I jointly share.

A:No.

A driving cycle is defined as the number of times the automobile is started and stopped.

Is it possible for my Acura dealer to reset it for me?

It is critical that all recommended maintenance is completed; if more than an oil change was required, your Acura dealer would be doing you a disservice by simply resetting the light, as the light is not just an oil change indicator; it also monitors the vehicle’s overall maintenance requirements, including tire rotations.

  • Q:Does the Acura Maintenance Minder System require me to monitor the amount of oil in my car?
  • The technology does not detect the presence of oil.
  • The indicator has not illuminated in the 6,000 miles that have passed since my previous maintenance appointment.
  • What am I supposed to do?
  • This is a perfectly typical state of affairs.
  • Is it possible for the Acura mechanic to inform me?
  • Your Acura technician has been trained on the Acura Maintenance Minder, and he or she will use the Forced Activation mode to identify what maintenance should be performed next on your vehicle.
  • Q:My Acura is furnished with break-in oil; should I replace it sooner rather than later?
  • In order to guarantee adequate engine break-in, the factory-fill engine oil must be allowed to remain in the engine until the first planned maintenance period after installation.

The oil used in the factory fill is the same as the oil used in Acura Service Replacement. The distinction lies in the Molybdenum lubricant, which is administered to particular internal engine components as opposed to the general engine.

2018 Acura MDX: How do you reset the change oil light?

To reset the change oil light on your 2018 Acura MDX, you must first switch on the ignition without starting the vehicle. For models with push-button start, you will need to press the start button twice while making sure that your foot does not rest on the brake pedal during the process. Scroll down the list of options on Your display using the buttons on the bottom of your screen until you reach Vehicle Settings and pick it. Continue scrolling until you reach Maintenance Reset / Maintenance Info, which will display the percentage of remaining oil life left on your vehicle’s engine.

  • April 9, 2020 – Philip A.
  • Follow the on-screen instructions as closely as you can, pausing the video if necessary.
  • Then, using the navigation buttons on the steering wheel, choose ‘car settings’ to complete the process.
  • Then, using the ‘sel/reset’ button, pick ‘maintenance information.’ Finally, choose ‘reset’ and hit the ‘sel/reset’ button to confirm your selection.

How To Reset Acura TL Oil Light Maintenance Code 1995 To 2013

Each time you replace the oil in your Acura TL, you’ll need to reset the oil life maintenance light on the instrument panel. In the event that you do not reset this light, the system will not be able to precisely track when you need to replace your oil. How to easily reset your oil life light without the need to pay a repair will be explained in detail in this helpful tutorial, step by step.

Reset The Oil Life Light in Your Acura TL

The majority of Acura TL models employ a similar approach to reset the oil change light; however, there may be some significant variances from one model to another in terms of which buttons or settings you must access in order to do this activity. Detailed procedures for each year from 1995 to 2013 are provided in the next section. Scroll down to the year of your Acura model and follow the on-screen instructions to successfully reset the oil life maintenance light on your Acura TL without any issues.

1995-1998

By placing your key into the slot just below the colored indication, you may reset the indicator.

1999-2003

  • Switch off your computer by turning the key to the off position. Hold both the ‘Select’ and ‘Reset’ buttons on the panel for a few seconds while turning the key in the ignition to the ‘On’ position (II). Don’t turn on the ignition
  • Press both the SELECT and the RESET buttons at the same time. Hold them for a total of 10 seconds until the indication is reset. Turn off the ignition and then start the car to ensure that the indication has been correctly reset.

2004-2005

  • Set the ignition to the desired setting (II). Don’t turn on the engine. Push the SELECT/RESET button and keep it down until the oil life indicator appears on the monitor
  • Then release the button. Press the button one more. Please keep holding it until you receive a confirmation message. Approximately five seconds should pass before this message appears. To select the OK option, use the SELECT/RESET button on your keyboard. The indication will be reset as a result of this operation. Remove the key from the ignition. Restart the car to ensure that the indication has been properly reset.

On the 2005 Acura TL, the following video demonstrates how to reset the oil life light:

2006-2013

  • Set the ignition to the ‘on’ position by turning the key (II). Don’t turn on the engine. Then, pressing the SELECT/RESET button situated on the steering wheel many times until the engine oil life is displayed on the display
  • Press and hold the SELECT/RESET button for at least 10 seconds to complete the process. On the screen, you will notice the engine oil maintenance reset mode in action
  • By pressing the INFO (up/down) button, select RESET from the drop-down menu. To restart the engine oil life maintenance indication, use the SELECT/RESET button on the instrument panel. You will see that the maintenance codes have disappeared and that the engine oil maintenance indicator has returned to 100. Remove the key from the ignition. Make sure you restart the vehicle to ensure that the indication is properly reset.

Listed below is a video that demonstrates how to reset the oil life indicator light on the 2013 Acura TL:

Watch Out for These Possible Sticking Points

When attempting to reset your oil light, it’s easy to overlook some of the small elements that might cause snags. Consider reading through the following points to see if any of them apply to your particular circumstance while troubleshooting your oil light.

  • If you have a keyless entry model, you will see that the ignition switch has been replaced by an engine start/stop button. Pushing the start/stop button once will not start the engine and is equal to the ignition (II) setting
  • However, pressing it twice will start the engine. If you drive an Acura RDX, the same methods apply as if you were driving an Acura TL from the same year, with one possible exception. To check the engine oil life if you are unable to view it, continually push the SELECT/RESET button located on the steering wheel until you see tire pressure and SH-AWD displayed. Remember that if you choose to reset your indication when the engine oil indicator indicates that the oil life has been exceeded by 15 percent, you must complete all necessary maintenance items before you may reset your indicator.

Conclusion

It’s no longer necessary to spend significant time out of your day when you bring your Acura TL into a shop to get the oil changed and the technician forgets to reset the oil maintenance light because of a simple oversight on the part of the mechanic.

You now have complete control over the process of resetting the oil change light on your Acura TL model. Simply follow the procedures outlined above for your specific model, which should take less than five minutes, and enjoy the possible hours saved by not having to wait at a mechanic’s shop.

How to reset acura tl oil light

The majority of Acura TL models employ the same process to reset the oil-change indicator light, however the controls or options available to you may range significantly from one model to the next. The following is a step-by-step approach for each year from 1995 to 2013, which is broken down by year. You may set your Acura T’s oil life maintenance light without any problems if you select the correct year for your Acura version and follow the steps in the method. 1995-1998: By placing your keys into the slot just beneath the indicator, you may reset the color of the indicator.

  • The key should be in the ‘off’ position when not in use. Then, while holding down the ‘Select’ and ‘Reset’ buttons on the control panel, turn the ignition key to the position you want (II). Please do not start the engine. Press and hold the SELECT button for a few seconds before pressing the RESET button. In order to get your indicator to reset, keep pressing them for 10 minutes. Turn off the ignition and then back on the engine to confirm that your indication has been appropriately reset.
  • Set the ignition to the appropriate setting (II). Stop the engine and get out of here. Hold the SELECT/RESET button down until you see the oil’s remaining life show on the screen
  • Then release the button. Please press the button a second time. Keep it in place until you receive confirmation communications from the company. In 10 seconds, the message should be displayed
  • Nevertheless,
  • Change the ignition settings by turning the key in the ignition settings position (II). Start by shutting down the engine. Then, continually press the button on your steering wheel until you can see the oil level in your engine shown on the dashboard display screen. Hold the SELECT/RESET switch down for at least 10 seconds after pressing it. Oil maintenance mode will be shown on the dashboard
  • You will notice that the maintenance codes have been removed from the display and that the oil maintenance indication has been reset to 100. Remove the keys from the ignition. Check that you restart the car to ensure that you have successfully reset the indication.

In the years 2004-2005, 2006-2013, and every time you change the oil in your Acura TLC, you will have to reset the maintenance of the oil light. It is important that you reset the oil light because otherwise, the system will be unable to accurately track the period when you will need to replace your oil again.

Acura MDX How to Reset the Service Light

In the event that you do hands-on maintenance on your Acura MDX, it is likely that you may be required to reset the vehicle’s service light at some time. Despite the fact that the owner’s manual suggests taking it to the dealer, you can avoid making an unnecessary trip by following these simple steps.This article applies to the Acura MDX (2001-Present).The service light on your Acura MDX can illuminate for a variety of reasons–whether it’s time for an oil change, new brake pads, or new tires, the service light on your Acura MDX will illuminate.

Check your owner’s handbook, and it’s likely that it will advise you to take your vehicle to a dealership.

Here’s how to find out what’s going on.

Material Needed

Do not turn the engine on completely; instead, turn the automobile on only partially and then off. If the oil light is not illuminated, push the select/reset button repeatedly until the blank screen, tire pressure, and SHAWD notification appear on the screen. Figure 1 shows an example of a formalized formalized formalized formalized formalized formalized formalized formalized formalized formalized formalized formalized formalized formalized formalized formalized formalized formalized formalized formalized formalized formalized formalized formalized formalized formalized formalized formalized formalized formalized formalized formalized formalized formalized formalized formalized formalized formalized formalized formalized formalized formalized formalized formalized formalized formalized formalized formalized formalized formalized formalized formalized formal You’ve probably had enough of seeing this by now.

Step 2 – Access the display signals

For 10 seconds, press and hold down the select/reset button on the remote control (or more).

The oil reset indication will now appear on the display, and you will be able to begin the oil reset operation at this point. Fig. 2: A diagram of the relationship between the two figures. You can begin working as soon as you see this screen.

Step 3 – Reset service light and display signals

Keep the select/reset button pressed and held down for a total of 10 seconds (or more). Following this, the oil reset signal will be shown on the screen, and you will be able to begin the reset operation. Fig. 2: A diagram of the relationship between the two figures You can begin working as soon as you see this screen appear.

Related Discussion

AcuraZine.com – Resetting Service Message B1 for the 2008 MDX

How do I reset my Acura maintenance light?

What is the procedure for resetting my Acura maintenance light? Clients of Scanlon Acura comes by or phone us from time to time to ask how to reset the maintenance light on their Acura vehicle. We feel that having one of our factory-trainedservicetechnicians reset the light while doing a thorough oil change service, which includes a comprehensive multi-point inspection and a complimentary vehicle wash, is the most convenient and effective method of resetting the light. Although we recognize that this ideal condition cannot always be achieved, we felt it would be worthwhile for us continue to attempt to be of assistance and assist you with resetting that light!

Then press and hold the SELECT and RESET buttons to the right of the steering wheel for a few seconds.

A blinking maintenance light on the instrument cluster will be followed by a steady illuminated light.

The light has now been turned off.

After that, press and hold the SEL/RESET button until the OIL LIGHT RESET option appears on the screen.

The light has now been turned off.

Navigation is simple.

screen and press SEL/RESET to exit the maintenance information.

The light has now been turned off.

(An example of the 2015 RDX maintenance reminder buttons display is given) We encourage you to contact us at (239) 433-1661 or visit our new state-of-the-art facility at 14270 S Tamiami Trail Fort Myers, FL 33912 Scanlon AcurainFort Myers, your Florida Acura Dealer!

Leave a Comment

Your email address will not be published. Required fields are marked *