- Never get caught by surprise with a dead battery! Install the CTEK Battery Sense monitor device on your car or boat battery and download the CTEK iOS or Android app. Then synch your phone or tablet to the CTEK Battery Sense unit and you can check your battery’s condition at any time and any place simply by check the CTEK app.
How long does a CTEK charger take to recondition a battery?
Once the analysis is done, the charger will spend anywhere from 30 minutes to 4 hours reconditioning your battery. This is good for deep cycle batteries that were previously fully or close to discharged.
Can CTEK revive battery?
CTEK Smarter Chargers recondition and help revive dead batteries. Our unique reconditioning step allows the battery to recover quickly and last longer. For the cost of a battery, a CTEK charger can keep all of your batteries in prime condition and offer you peace of mind for years to come.
Can you jump start with a CTEK?
Jump Starting a Vehicle’s Battery Can Cause Irreparable Damage, Says CTEK. Using a smart battery charger is the safe and simple way to recharge any vehicle battery. With a smart charger, such as the CTEK MXS 5.0, it is possible to monitor the charge level of a vehicle”s battery.
Can I leave my CTEK charger on all the time?
Can I leave the charger connected to the battery for a long time? Yes. CTEK chargers are designed to fully charge a battery and then automatically switch over to long term maintenance. Before leaving the charger unattended for a long time, ensure that the battery is fully charged, as indicated by the green LED.
How often should you recondition a car battery CTEK?
However, Smokey did caution us that if we use the Recondition mode too often, we could damage the battery by gassing it too much. He recommended only using it 1 or 2 times a year if the battery is otherwise in good shape.
How do I monitor my car battery charge?
How to Test Your Battery Voltage with a Voltmeter
- Make sure your vehicle is turned off.
- Remove the battery’s positive terminal cover.
- Check the reading.
- Any voltage above 12.9 volts is a good indicator that your battery has excessive voltage.
- Charge your battery if the voltmeter display a voltage below 12.4.
What does a CTEK Smartpass do?
Smartpass 120S is a 120A Power Management Solution which distributes, controls and maximises the available energy from your alternator to power service batteries and consumers.
Can AGM battery be reconditioned Ctek?
RECOND Programme mode First off, only use RECOND mode with a standard Lead Acid Battery or Enhanced Flooded Battery (EFB) (this includes calcium EFB batteries). RECOND will not help an Advanced Glass Matt (AGM) battery. It could even harm a Gel battery.
What is Ctek AGM mode?
AGM – or ‘ dry’ batteries – are the latest step in the evolution of lead-acid batteries. Instead of using water or a gel, an AGM uses a fibreglass separator to hold the electrolyte in place. Gel batteries use a gelified acid.
What is Ctek Recond mode?
When you select the recond mode on a charger with that feature you will still charge a battery normally through to stage 5 but in stage 6 it will apply a higher voltage to equalize or overcharge the battery to allow a full absorption charge to be performed.
Is CTEK a trickle charger?
There are various types of battery charger currently available – mostly smart chargers and trickle chargers. Rather than sending in a charge and estimating what the battery needs, a CTEK charger will stay in constant communication with the battery, reacting and charging only when it is needed.
Where are CTEK chargers made?
CTEK battery charging solutions – the last word in quality There’s a simple reason why CTEK is a world leading manufacturer: quality is at the heart of everything we do. Our products are the result of continuous extensive investment in quality, safety and performance at our state of the art facility in Dalarna, Sweden.
Which CTEK charger is best?
The CTEK MXS 5.0 is a good example of a product that has received global recognition. This intelligent battery charger and maintainer is perfect for charging car batteries, and also has a dedicated motorcycle mode too. This compact, shock-proof unit is compatible with all 12V lead-acid batteries.
CTX BATTERY SENSE
With Bluetooth connection, this free smartphone application checks the battery’s charge level. CTX BATTERY SENSE is a smart battery management gadget that operates using Bluetooth® technology. The information it provides on the level of your battery’s charge can assist you in avoiding vehicle failures and maximizing the performance of your battery. Simply download the free app, attach the Battery Sense Monitor to your battery, and follow the in-app instructions, and your mobile phone will provide you with data 24 hours a day, seven days a week, all year long.
Moreover, if the charge level of your battery drops to a critical level, Battery Sense will alert you that it is time to go for your CTEK battery charger.
- The device automatically syncs through Bluetooth®
- It continuously monitors the charge of the battery. Stats are stored for up to three months
- A two-year guarantee is included.
Technical data
Protection on a granular level IP67Warranty is for two years.
CTEK Battery Sense Device Monitors Battery Condition
No longer will you be caught off guard by a dead battery. The CTEK Battery Sense Monitordevice to be connected to your car or boat’s battery, and the CTEK iOS or Android app should be downloaded. Then connect your phone or tablet to the CTEK Battery Sense device, and you’ll be able to monitor the state of your battery at any time and from any location by using the free CTEK app.
Why You Need a CTEK Battery Sense Monitor
With its straightforward design, the CTEK Battery Sense Monitor prevents the unpleasant surprise of a dead battery. Additionally, it notifies you when it is time to recharge your battery. Some instances of why you should use a CTEK Battery Sense Monitor are provided below. 1st Scenario: You commute to work and go grocery shopping in a short amount of time. Alternatively, you may drive in stop-and-go traffic. Because you never drive for a long enough period of time or at a high enough engine RPM to fully recharge your car’s battery, driving under these conditions is extremely taxing on your vehicle’s battery.
- Lead-acid batteries lose capacity when exposed to cold temperatures, and cold engines require more amps to start up than they would otherwise require.
- The short drives are just unable to compensate for all of the lost power.
- However, by connecting a CTEK Battery Sense Monitor to your battery, you will be able to verify the state of your battery before you turn the key.
- All lead-acid batteries self-discharge at a rate of 1-2 percent per day, and this rate is constant (depending on temperature).
- When you add up the self-discharge rate plus the battery depletion caused by the vehicle’s computer, your battery might be unable to start the vehicle in as little as thirty days.
- Scenario 3: You are the owner of a yacht.
Is it necessary for me to explain this to you? Nobody likes to be stranded on a boat with a dead battery, yet that is exactly what happens. Installing a CTEK Battery Sense monitor on your boat will allow you to know the state of your battery before you even go onto the dock.
How to Install a CTEK Battery Sense Monitor
CTEK provided me with a sample device that I could install and test. It is quite simple to set up and use. Here’s what you should do: Using a socket/ratchet or a wrench, loosen the clamp on the positive battery connection terminal. To connect the red ‘C’ lug terminal from the CTEK Battery Sense device to the positive terminal, slide the terminal between the nut and the positive connection. Tighten the nut a little more. NOTE: When working on the positive terminal of the battery when the negative battery terminal is attached to the battery, take care not to come into touch with any engine or sheet metal body elements with the wrench or ratchet.
The operation is repeated on the negative battery terminal, but this time inserting the black ‘C’ lug terminal from the CTEK Battery Sense device between the nut and the terminal bolt instead of the nut.
Set up the app
To get started, go to the Apple or Google Play store and download the CTEK Battery Sense app, then install it on your smart device. Then, on the registration screen of the app, input the Battery Sense serial number that you obtained before. Discover and input the Battery Sense serial number that may be found on the label or box of the device. On the next screen, provide the information about the car. This is especially useful if you’re installing numerous CTEK Battery Sense units on your family’s fleet of vehicles at the same time.
Monitor your battery condition
As soon as you have completed the setup procedure, the battery state will be shown. If you’re using an iOS device and want to keep an eye on the health of your battery on a continual basis, simply leave the CTEK Battery Sense app open. On an Android smartphone, go to the app’s settings and check the box that says ‘allow background updates.’
Secure the Battery Sense unit
Make use of the zip ties that included with the packaging to keep the CTEK Battery Sense Monitor in a safe location in your engine bay. Disclaimer from the Federal Trade Commission: CTEK did not pay me to publish this piece. As a side note, CTEK gave me with this trial device free of charge with no expectation that I would write a favorable review. My blog philosophy, on the other hand, is that I will never publish a favorable review on a product unless I truly enjoy it and believe it is a good choice for my audience.
The year is 2019.
CTEK Battery Sense – Apps on Google Play
The CTEK Battery Sense app works in conjunction with your CTEK CTX Battery Sense Monitor to provide you with all of the information you want on the status of your vehicle’s battery, right in the palm of your hand. It has been specifically developed to assist you in rapidly and correctly monitoring the performance of your battery in order to keep you safe on the road and prevent breakdowns. Simple to set up and operate Syncs with your phone in seconds using Bluetooth technology. Battery health monitoring for 12V lead acid batteries is performed on a continuous basis.
You may also use the manual input for battery capacities ranging from 5Ah to 200A.
Data for certain days or periods may be seen on a zoomable graph.
Furthermore, if your battery’s charge is approaching a critical level, the CTEK Battery Sense app will alert you to the fact that it is time to reach for your CTEK charger. Please see www.ctek.com for further information about Battery Sense.
CTEK battery sense review – How to avoid ever having a flat battery
I suppose my discovery of theCTEKbattery sense began in the same manner that the majority of people find their motorcycles: by accident. On this gorgeous morning, the entire countryside was bathed in the warm glow of the rising sun, which was a welcome sight. It was the ideal day for me to take my Harley-Davidson to work. It was also a very crucial day for me because I had a job interview scheduled. Despite my nervousness, I dressed for the occasion and went to the garage to prepare my thoughts for what was ahead.
- My Street Bob wouldn’t start for some reason, thug.
- And I had even started her the night before to make sure everything was in working order.
- I tried everything to get her going,’sputter, sputter, sputter,’ but it didn’t work.
- Once I had determined how much time was left, I plugged her into myCT5 Powers Sport charger to charge her up and give her a ten-minute boost.
- I’ve just completely depleted the battery.
- However, I was dressed in biking gear!
- I needed to make a change.
Anyway, long story short…
My bike wouldn’t start because the battery was completely dead. I had to contact ahead and let them know I was going to be late because of a car problem, but I only arrived ten minutes late in the end. I’ve always been very good about battery care, utilizing a trickle charger and doing battery reconditioning on a regular basis, but this morning I realized I needed to do a little more to keep things running smoothly. The disappointment of getting out to the garage and discovering that you are unable to ride due to a flat tire.
- The fact that it’s completely avoidable has motivated me to discover a solution.
- So, what do I think it’s worth?
- WithBowtex Kevlarleggings, you may wear any apparel while still having all of the protection provided by the protective base layer beneath the garment.
- Suddenly, I’m dressed for an interview.
What is it
It’s a little gadget that you connect to your vehicle’s battery and conceal under your seat or in another discreet location in your vehicle. This little gadget then checks the condition of your battery and sends the information to your smart phone through Bluetooth. You could be wondering, what’s the point? Ultimately, batteries can become sick, lose their ability to produce power, or even fail completely. However, with proper battery maintenance, you can extend the life of your battery and make it significantly more reliable – resulting in a more dependable bike, fewer breakdowns, and less money spent on batteries over time.
Batteries do not have a status monitor and, in most cases, will not tell you that they are running low on power until it is too late and your vehicle will not start.
The apps are completely free, and they will automatically update whenever you are within Bluetooth range.
The option to have several devices attached to a single app is another amazing feature. If you’re fortunate enough to have many bicycles or automobiles, you can sync them all together with this feature.
Ease of use
All of the information is provided in a very straightforward visual display within the app; for example, the percentage of battery charge is shown by color coding, which also indicates the action that must be taken:
- Red is depressed – take command now
- Warning Color: Yellow – charge as quickly as possible
- Happy Green – The battery is in good working order.
The percent history of your batteries will then be put on a graph for you to examine. This is quite useful for observing the progression of the battery’s degeneration over a period of time. If there is a sudden drop in charge, it is most likely due to something being left on that is draining the battery’s power; a steady decline could indicate a battery that is in need of reconditioning; but a gradual drop in charge could simply be the result of being parked for an extended period of time. This may all be assisted by utilizing a CTEK CT5 Powers Sport charger, which can vary in effectiveness depending on the severity of the degeneration.
If your battery status changes or reaches a critical level, the app will send you a push notice, which you can view in your notification center.
You may then rejoin, and all of the previously stored data from the time you were gone will be loaded as well.
Stats given:
- A percentage of the battery’s charge
- Instructions on what steps are necessary
- Temperature and voltage of the battery
The Techy Bits
- This battery charger is suitable for any automobile, motorbike, and engine starting batteries with a capacity of 4.5AH or more
- Compatible with Android operating systems 4.4 and higher, iPhone operating systems 7 and higher, and Bluetooth® 4.0. Smart phone application and monitor that is simple to use and monitor with a free app download
- It is possible to sync with numerous displays in order to keep track of all of your automobiles. It keeps track of up to three months’ worth of data. Notifications when the battery’s state of charge reaches a critical level or when measurements have not been made for seven days
- Warranty of two years
Limitations
- Because it is Bluetooth, you must be within range of your bike in order to use it. The statistics are not available to me since my garage is a little too far away from my house to obtain them without leaving the house. While not a restriction of the product, it did need a lot of wiggle room and rearranging of wire on my Street Bob to get the little gadget to fit on the battery – likely due to the fact that I already had a few extras attached to the bike. I was able to get it to operate without any problems, although you may need to squeeze and clean a bit
£££
Their cost is on the higher end at roughly £40-50 per unit, but it’s all about the value you place on being able to ride, and for me, having an automated notice if my battery needs maintenance is well worth the money. Saving yourself from the letdown of a ‘Sputter, Sputter, Sputter’ is well worth the investment. Additionally, by checking the health of your battery, you may avoid a deep discharge, which will result in a loss of performance and the need for a replacement battery sooner rather than later.
Highlights
- It is compatible with all 12V lead acid batteries. Ensures that your battery is fully charged and ready to go when you are
- Battery status information delivered directly to your smartphone
Tips From ExperienceThe Girl On A Bike battery sense charger ctek ct5 powersport modes recondition’ data-image-caption=’ The Girl On A Bike battery sense charger ctek ct5 powersport modes recondition’ data-medium-file=’ ssl=1′ data-large-file=’ ssl=1′ loading=’lazy’ src=’ alt=” width=’446′ height=’364′ srcset=’ ssl=1 1646w,ssl=1 1024w’ sizes='(max-width: 446px) 100vw, 446px’ data-recalc-dims=’1’>
- If you have to pick between the CT5 Powersport battery charger and the CT5 Powersport sensor, I strongly advise you to purchase the charger over the sensor. I’ve found that bikes may be left unridden for weeks at a time, so you can leave this plugged in and be certain that your ride will be ready to go when you arrive. This battery charger and maintainer is particularly intended to charge, maintain, and recharge batteries. It has three completely automated charging and maintenance programs: Normal, AGM, and Reconditioning. When I’m parked, I’m in the habit of leaving it permanently attached because it’s meant to do so in order to prevent over or under charging. It is simple to use and is compatible with all types of 12V lead acid batteries used in powersports. It’s almost magical how a completely dead battery that you thought was destined for the scrap heap can be entirely reconditioned and continue to operate dependably following a CT5 overhaul — this saves you money on battery replacement costs.
Overall Rating
A little but extremely effective and useful gadget that gives you the assurance that your transportation will be ready to go when you are is ready to go. Maintains your battery for the longest possible life while providing the most dependable performance so that nothing stands in the way of your next trip. When it comes to dirt bike riding and racing, I’m on a quest to prove that nothing is impossible if you put your mind to it. If you’re new to my page, know that it’s about more than just dirt bike riding and racing.
You may find me as Vanessa, The Girl On A Bike, on social media platforms such as Instagram, Facebook, and YouTube, as well as my website, www.thegirlonabike.com.
CTX BATTERY SENSE
NZD559.00eachCTEK CS FREEThe CTEK CS FREE is the world’s first totally portable battery charger and maintainer to use Adaptive Boost technology, making it the most advanced in its class. You may charge and maintain any 12V lead-acid or lithium car battery at any time and from any location without the need for an electrical outlet. And if your battery is completely depleted, CS FREE’s unique Adaptive Boost technology can recharge it in 15 minutes or less. Portable charging and maintenance that you can carry with you everywhere you go without being tethered to a power source When completely charged, the internal battery may last for up to a year.
Solar or a 12V battery can be used to charge and power the device for longer-term maintenance charging and powering.
When you use the Countdown function, it will tell you how long it will take for your battery to be fully charged.
USB-C and USB-A ports are available for charging devices such as laptops, cellphones, and tablets. A new ergonomic design with a strong and sturdy casing has been introduced. Warranty for ‘peace of mind’ for two years Additional accessories that are available are as follows:
- Alligator clips are used for the DC input so that a battery can be used to charge another battery. (Charger from one DC source to another DC source)
- Renewable energy source (60W) to recharge the onboard battery or pass-through to charge any device connected to the CS Free’s USB-A, USB-C, or Alligator Clips. Cig PlugDC input, allowing you to charge your CS Free with a cigarette lighter converter. Using this feature, you may recharge the internal battery while also charging or powering the outputs.
| TECHNICAL DATA | |
| INPUT USB-C | 5 VDC – 25 VDC, 3 ADC/60 W max |
| OUTPUT | 12 V, 20 A/240 W max |
| START VOLTAGE | 3.0 V |
| AMBIENT OPERATING TEMPERATURE | -20 ˚C to +50 ˚C (- 4 °F to +122 °F) |
| AMBIENT STORAGE TEMPERATURE | -20 ˚C to +45 ˚C (- 4 °F to +113 °F) |
| BATTERY CHEMISTRY | Lead acid, Lithium |
| BATTERY TYPES 12 V | WET, MF, Ca/Ca, AGM, EFB, GEL, LiFePO4 |
| BATTERY CAPACITY | 10-130 Ah |
| DEGREE OF PROTECTION | IP54 |
| WARRANTY | 2 years |
| NET WEIGHT (UNIT WITH CABLES) | 1.4 kg |
| DIMENSIONS | (L x W x H) 248 x 98 x 78 mm |
| USB-A OUTPUT | 5 VDC, 2.4 ADC/12 W max |
| USB-C OUTPUT | 5 VDC, 9 VDC, 12 VDC, 15 VDC, 20 VDC, 3 ADC/60 W max |
| MAINS ADAPTER | |
| INPUT | 100 VAC – 240 VAC, 50 Hz – 60 Hz, 60 W max |
| OUTPUT USB-C | 5 VDC – 20 VDC, 3 ADC, 60 W max |
| CABLE LENGTH | 1 m |
| CABLE TYPE | USB-C |
| INTERNAL BATTERY | |
| CAPACITY | 66 Wh |
| CELL CHEMISTRY | Polymer Lithium-Ion |
| CELL TYPE | Pouch Cell |
| DISCHARGE TEMPERATURE | -20 ˚C to +50 ˚C (- 4 °F to +122 °F) |
| CHARGE TEMPERATURE | 0˚C to +45˚C (32˚F to 113˚F) |
| SHELF LIFE | 1 year |
| LIFE SPAN | 300 cycles, 80% |
CTEK CTX Battery Sense Battery Management Tool
A battery management gadget called the CTEK CTX Battery Sense is what we use in our 4WD to check the status of our battery, which is connected to a 12V electrical system.
CTEK CTX Battery Sense
It is a smart battery management gadget that uses Bluetooth to communicate with the CTEK CTX Battery Sense. You may check the level of charge of your battery by connecting a tiny device to your battery and using an application on your mobile device to view the status of your battery. The CTEK CTX Battery Sense battery management tool is a low-cost add-on that gives you with enough valuable information about the condition of your battery to make informed decisions. We have installed the CTEK CTX Battery Sense in our 4WD’s second (dual) battery.
CTX Battery Sense Features
The following are some of the most important characteristics of the CTEK CTX Battery Sense battery management tool.
- When in range, the device automatically syncs battery data over Bluetooth. Monitors the battery charge of your 4WD on a continuous basis. Battery data is stored for up to three months
- Battery voltage, charge status %, and temperature information are provided. It is simple to install and just takes a few minutes to get everything up and running
- IPhone and Android users can get this free application. The IP67 rating protects against water and dust infiltration. This item comes with a 2-year warranty. When purchasing extra batteries, it is possible to utilize the Battery Sense application to monitor numerous batteries at the same time.
Why We Installed the CTX Battery Sense?
The electrical setup for your 4WD 12V vehicle is one of the most important aspects of any excellent setup, as any 4WD Adventurer is well aware. Our 4WD electrical arrangement provides electricity for our fridge, on-board compressor, lights, UHF communications, charging outlets, power to our camper trailer, and our 240V inverter, among other functions. If something goes wrong with our electrical arrangement, we’re going to be in a bad place, and whatever enjoyment we had on our trips would be put to an abrupt halt.
- Battery management systems (BMS) are certainly beneficial and feature-rich, but we are quite content to just flick a switch to turn on our lights rather than having to use an application on our phone to do this task.
- In order to be able to monitor the health of our second (dual) battery, we decided that rather than investing thousands of dollars on a battery management system, we would install the CTEK CTX Battery Sense, which was far less expensive.
- The CTEK Battery Sense phone application provides you with information on your battery’s voltage, charge state, and temperature, among other things.
- The CTEK CTX Battery Sense provides us with enough information to determine where our battery charge is now located as well as how the status of charge has changed over the day, week, or month in which we are using the device.
Connecting to Your Battery
Our second (dual) battery was quickly and easily equipped with the CTEK CTX Battery Sense gadget, which took only a few minutes. The device comes with positive and negative terminals, which must be linked to the positive and negative terminals on your battery in order for it to function properly. The positive cable is equipped with a flat fuse that is incorporated into the cable. The two wires are attached to a compact black device with mounting holes on the back, which allows you to put it with a pair of cable ties out of the way if desired.
All that is required to connect the gadget to your battery is the above procedure. Once connected, you’ll need to download the app and configure your battery settings in the app once it’s installed.
Battery Sense Phone Application
Once the CTEK CTX Battery Sense gadget has been linked to your battery, go to your phone’s application store and download the Battery Sense application. The program, which is accessible for both iPhone and Android smartphones, is completely free to download. The program may now be connected to your battery after being downloaded and installed on your computer. When you connect to the phone application, you will be prompted to enter a code that is hidden behind the Battery Sense unit. Once this is completed, you can give your battery a name and select the appropriate battery size based on the number of Amp Hours it contains (AH).
Battery Sense Data
Although the information offered by the CTEK CTX Battery Sense application is limited, we believe it to be all that is truly necessary. It will not tell you how many amps are being pulled from your battery at any one time, but for us, this is not a major deal because the state of charge and voltage data supply us with sufficient information. The information presented includes the voltage of the battery, its level of charge, and its temperature. When you pick your battery on the app, you will be presented with a real-time visual overview of your battery’s current status.
You may then choose from the drop-down menus below this graphic whether you want to see more specific information on voltage, charge stage, or temperature.
There are several zooming options available for the line graph, allowing you to view the history spanning three months, a few hours, or even a few minutes.
If you detect a significant voltage decrease during a 30-minute period, but nothing was turned on, this will provide you with enough information to conclude that something is wrong and that something is sucking power from your battery.
Great but Cheap Addition
Even if you do not have the funds to purchase an expensive battery management system (BMS), something as simple as the CTEK CTX Battery Sense battery management tool might be an excellent low-cost addition to your system. In addition to being compact, the machine is also exceedingly simple to set up. Using the Battery Sense application on your phone, you may gather more than enough information to guarantee that your battery configuration is functioning properly. However, getting up and flicking a switch isn’t all that tough when you consider how difficult it is to turn on your lights.
Given that the CTEK CTX Battery Sense device is just about $50, it is an unusually inexpensive add-on given the information it provides on your battery’s condition.
Overall, we feel that this is a fantastic and reasonably priced small item if you want a little more information on the status and health of your battery and its capacity.
More information about the CTEK CTX Battery Sense battery management tool may be found on the company’s website.
You should be able to get them for roughly $50 on the internet. This post was not sponsored; instead, we purchased the equipment and are providing our honest opinions on how it works and what we think of it.
CTEK Battery Sense 12V Battery Monitor – 40-149
CTEK Battery Sense provides a one-of-a-kind continuous assessment of battery state. CTEK allows you to check the battery state of your car from the convenience of your smartphone. Battery Sense is a one-of-a-kind approach that allows you to check the state of your vehicle’s battery using a smartphone app for iOS and Android devices that connects over Bluetooth. Technical Specifications for the CTEK Battery Sense:
- 40-149
- Rated Voltage DC: 7.0 – 16Vdc
- Min Battery Voltage: 7.0Vdc
- Max Current Consumption: Less than 1mA @ 12.5V
- Ambient Temperature: -30C to +85C
- Battery Types: 12V Lead Acid Batteries
- Battery Capacity: 20-200Ah
- Insulation Class: IP67
- Warranty: 2 Years
- Model Number: 40-149
- Rated Voltage DC: 7 – 16Vdc
To speak with a battery professional regarding the CTEK Battery Sense device, please contact us by phone at 1-877-775-4381 or by email using the contact us option at the top of this page. A bluetooth connection allows the CTEK Battery Sense 12V battery to monitor the state of your car battery and deliver status updates and alarms directly to your smartphone.
CTEK Battery Sense
The CTEK Battery Sense app works in conjunction with your CTEK CTX Battery Sense Monitor to provide you with all of the information you want on the status of your vehicle’s battery, right in the palm of your hand. It has been specifically developed to assist you in rapidly and correctly monitoring the performance of your battery in order to keep you safe on the road and prevent breakdowns. Simple to set up and operate Syncs with your phone in seconds using Bluetooth technology. Battery charge monitoring for 12V lead acid batteries on a continuous basis Information regarding the charge status of your battery that is simple to grasp Instantaneous readings of the voltage and temperature of your battery Battery capacities ranging from 5Ah to 200Ah can be entered manually.
- Data for certain days or periods may be seen on a zoomable graph.
- Furthermore, if your battery’s charge is approaching a critical level, the CTEK Battery Sense app will alert you to the fact that it is time to reach for your CTEK charger.
- – Connection procedure has been simplified and made speedier.
- Obtaining the sender’s identification number.
- – A button to reconnect has been added to the Detail screen.
Ratings and Reviews
Have a total of three Battery Sense Devices on hand. I had to change my iPhone, and the app transferred over without issue, but it would not connect. Deleted and reinstalled an application, physically unplugged all devices, and waited more than 30 seconds before physically reconnecting batteries. The Bluetooth settings on the iPhone were checked; the App was launched; and the devices were attempted to be detected as new on a clean install; all three failed to connect. A complete and total waste of $450 on equipment that was only 10 months old.
The battery chargers are fine since, for the most part, they do not make use of or demand the usage of applications. To make matters worse, the link to CTEK on this app listing redirects you to a Page Not Found warning. PATHETIC. WET. DISGRACEFUL AS F
Just Rubbish
The bad news is that if you’re reading the app reviews, it’s likely that you’ve already purchased the gadget. I purchased one, but it would not connect. Customer care informed me that there had been a defective batch and that I would be given another one. It functioned for a short period of time before failing. When the phone is only a few inches above the gadget, it will not connect. It will not be able to save you from a dead battery in any way.
App won’t load
It was running OK until the most recent update, after which it simply freezes and won’t load. I spent a lot of money on this product, and it is now completely worthless because the app does not work. Please fix this. In addition, the developer, CTEK Sweden AB, has not given Apple with any information regarding its privacy policies or data processing. More information can be found in the privacy policy of the developer.
No Details Provided
When the developer submits their next app update, they will be obliged to include information about privacy practices.
Information
SellerCtek Sweden ABSize32.3 MBCompatibilitySellerCtek Sweden ABS iPhone It is necessary to have iOS 10 or later. iPod touchIt is necessary to have iOS 10 or later. LanguagesEnglish, Danish, Dutch, Finnish, French, German, Italian, Norwegian Bokml, Spanish, and Swedish are some of the languages spoken throughout the world. Age Rating4+Depends on Location This app may utilize your location even when it is not open, which might reduce the battery life of your smartphone. CTEK 2016PriceFree Copyright CTEK 2016PriceFree
Supports
- Vehicles from the United Kingdom and Continental Europe, a warehouse, and gift ideas
- There were BN1 to BJ8 Austin Healeys built from 1953 to 1968, as well as the Austin Healey Sprite (1958-1971) and the MG Midget (1961-1979).
- Among the Jaguar XK engines are the Jaguar XK120, XK140, and XK150 (1949-1961)
- Jaguar E-Type Series 1 and 2 (1961-1970)
- Jaguar E-Type V12 Series 3 (1971-1974)
- Jaguar Mark II and Daimler V8 (1959-1969)
- Jaguar XJ6 Series I-III and Daimler Sovereign Series I-III (1972-1992)
- Jaguar Mk7, Mk8, and Mk9 (all 1950-19
- MG T-Type: TA, TB, TC, TD, and TF (1936-1955)
- MGA (1955-1962)
- MGB (1962-1980)
- MGC (1967-1969)
- Austin Healey Sprite (1958-1971) and MG Midget (1961-1979)
- MGF and MG TF (1995-2005)
- MGR V8 (1992-1995)
- Austin Healey Sprite (1958-1971)
- Austin Healey Sprite (1961-1979)
- Austin Hea
- Triumph TR2 to TR4A (1953-1967)
- Triumph TR5, TR250, and TR6 (1968-1976)
- Triumph Spitfire MkIII, MkIV, and 1500 (1967-1980)
- Triumph Stag (1970-1977)
- Triumph TR7 and TR8 (1975-1981)
- Parts and accessories for all Triumph models
- Triumph TR2 to TR4A (1953-1967)
- Triumph TR2 to
- A complete inventory of Land Rover Series II, IIA, and III vehicles from 1958 to 1985
- Land Rover 90, 110, and Defender vehicles from 1983 to 2006
- Range Rover Classic vehicles from 1970 to 1996
- And replacement parts and accessories for all Land Rover models.
- Rolls Royce Silver Cloud and Bentley S-Series (1955-1966)
- Rolls Royce Silver Shadow and Bentley T-Series (1965-1980)
- Rolls Royce Silver Spirit (1980-1998) and Bentley Mulsanne (1980-1992)
- Rolls Royce Silver Cloud and Bentley S-Series (1955-1966)
- Rolls Royce Silver
CTX Battery Sense enables you to monitor and regulate the health of your battery. Simply connect the Battery Sense monitor and download the free Battery Sense App to get started. (Please note that the mobile devices pictured are not included in the consignment.) Breakdowns are prevented by using a smart battery health monitor. With this one-of-a-kind Bluetooth connected smart monitoring gadget, you can easily keep track of the health of your battery. It’s simple to set up, and the data is given through a free iPhone or Android app that can be downloaded.
- iOS 7 (or later) and Bluetooth 4.0 hardware are required (iPhone 4S or newer).
- The maximum amount of current usage At 12.5VA, less than 1mA is used.
- Warranty A two-year warranty is provided.
- For further information on what information is contained in cookies, please go to the pagePrivacy Policy (in English).
CTEK Battery Sense Battery Monitor
CTEK Chargers provide power to some of the most famous power sports manufacturers in the world. They feature a proprietary charge algorithm that guarantees that your bike’s batteries are in the greatest possible condition, allowing them to survive for a longer period of time. These batteries interact with and read your battery on a regular basis, ensuring that it only charges when it is needed to do so.
They feature one of the most technologically advanced smart battery chargers available on the market today. CTEK should be your first choice if you want to extend the life of your motorbike battery.
The proud heritage that drives the future
The history of CTEK began in a little village named Vikmashyttan in the Swedish province of Dalarna. Bengt Wahlqvist, a Swedish inventor and the founder of CTEK, invented the world’s first battery charger that utilized electronic pulse technology around 30 years ago. They changed the face of the motorbike business by developing the world’s first ‘smart’ battery charger. Now, they are committed to providing world-class technologies and ideas that improve the biking experience for everyone. CTEK has set itself the objective of maximizing battery performance from the outset of the company’s existence.
They test the boundaries of current science in order to make ground-breaking findings that will help the industry adopt breakthrough battery charger technologies.
Every year, they sell more than a million battery chargers in more than 70 countries throughout the world.
Why Choose CTEK Battery Chargers
CTEK Products are the result of the most cutting-edge technology available in the motorbike battery charger business today. Their MXS 5.0 Battery Chargers automatically adapt to the temperature to provide the greatest charging performance possible, no matter what the conditions are. In order to keep your batteries in the best possible condition, they contain a reconditioning mode as well as automated charging and maintenance. These battery chargers are controlled by a sophisticated microprocessor that is capable of determining the status of your battery.
Other CTEK Battery Accessories, such as the CTEK Connect Extension Cable and the CTEK LED Comfort Eyelet M6, are available for purchase.
They are interchangeable with the CT5 series from CTEK.
This adapter makes it possible to connect hard-to-reach batteries in a safe and permanent manner, allowing for simple access.
Why You Need CTEK Battery Chargers
The alternator on your motorbike is normally responsible for charging your motorcycle battery. You may find that the power your battery receives from your bike is insufficient to provide you with the performance you want when you’re out for a long ride or planning an adventurous excursion on the trails. Furthermore, when your batteries are not charged for extended periods of time between usage, it reduces the life lifetime of your batteries.
That’s why, if you’re an adventure seeker who wants to push the limits of your motorcycle, you should always have battery chargers on hand. Motorcycle battery chargers assist to guarantee that your bike is always ready for a ride, as well as that your batteries have the longest potential life.
Shop CTEK Battery Chargers Online
Batteries for motorcycles serve as the beating heart of your vehicle! Use only CTEK Battery Chargers and CTEK Charger Accessories to keep your motorcycle’s batteries in peak condition at all times. The CTEK XS 0.8 (12V 800mA) Battery Charger, the CTEK LED Comfort Eyelet M6, and the CTEK MXS 5.0 (12V 5A) Battery Charger are among the best-selling CTEK products available at AMX. On all goods, AMX provides complimentary delivery. We have a large number of shop locations in Victoria, Queensland, New South Wales, and South Australia, among other states.
Do not hesitate to contact our experts if you want assistance in selecting the best CTEK Parts for your particular bike type.
They feature a proprietary charge algorithm that guarantees that your bike’s batteries are in the greatest possible condition, allowing them to survive for a longer period of time.
They feature one of the most technologically advanced smart battery chargers available on the market today.
The proud heritage that drives the future
The history of CTEK began in a little village named Vikmashyttan in the Swedish province of Dalarna. Bengt Wahlqvist, a Swedish inventor and the founder of CTEK, invented the world’s first battery charger that utilized electronic pulse technology around 30 years ago. They changed the face of the motorbike business by developing the world’s first ‘smart’ battery charger. Now, they are committed to providing world-class technologies and ideas that improve the biking experience for everyone. CTEK has set itself the objective of maximizing battery performance from the outset of the company’s existence.
They test the boundaries of current science in order to make ground-breaking findings that will help the industry adopt breakthrough battery charger technologies.
Every year, they sell more than a million battery chargers in more than 70 countries throughout the world.
Why Choose CTEK Battery Chargers
CTEK Products are the result of the most cutting-edge technology available in the motorbike battery charger business today. Their MXS 5.0 Battery Chargers automatically adapt to the temperature to provide the greatest charging performance possible, no matter what the conditions are. In order to keep your batteries in the best possible condition, they contain a reconditioning mode as well as automated charging and maintenance. These battery chargers are controlled by a sophisticated microprocessor that is capable of determining the status of your battery.
Other CTEK Battery Accessories, such as the CTEK Connect Extension Cable and the CTEK LED Comfort Eyelet M6, are available for purchase.
They are interchangeable with the CT5 series from CTEK. The Eyelet M6 is ideal for batteries that are difficult to reach or for situations where clamps are not an option. This adapter makes it possible to connect hard-to-reach batteries in a safe and permanent manner, allowing for simple access.
Why You Need CTEK Battery Chargers
The alternator on your motorbike is normally responsible for charging your motorcycle battery. You may find that the power your battery receives from your bike is insufficient to provide you with the performance you want when you’re out for a long ride or planning an adventurous excursion on the trails. Furthermore, when your batteries are not charged for extended periods of time between usage, it reduces the life lifetime of your batteries. That’s why, if you’re an adventure seeker who wants to push the limits of your motorcycle, you should always have battery chargers on hand.
Shop CTEK Battery Chargers Online
Batteries for motorcycles serve as the beating heart of your vehicle! Use only CTEK Battery Chargers and CTEK Charger Accessories to keep your motorcycle’s batteries in peak condition at all times. The CTEK XS 0.8 (12V 800mA) Battery Charger, the CTEK LED Comfort Eyelet M6, and the CTEK MXS 5.0 (12V 5A) Battery Charger are among the best-selling CTEK products available at AMX. On all goods, AMX provides complimentary delivery. We have a large number of shop locations in Victoria, Queensland, New South Wales, and South Australia, among other states.
Do not hesitate to contact our experts if you want assistance in selecting the best CTEK Parts for your particular bike type.
CTX Battery Sense Mobile Monitor – by CTEK
The shop will not function properly if cookies are deactivated on your computer or device. €65.00 In stock and ready to ship in 1-2 business days On your cell phone, you may keep track of the battery life of your vehicle. A free iPhone or Android App delivers data from the CTX Battery Sense Mobile Monitor’s one-of-a-kind Bluetooth-enabled smart monitoring gadget, which is simple to install. CTX Battery Sense Mobile Monitor – by CTEK is available for purchase in increments of one unit (CTX Battery Sense Mobile Monitor).
- Equipment and guidance that has been tested and proven You may put your faith in us. 14-day money-back guarantee Guarantee
- Off-road construction was used. Tough
- A smart battery management instrument that is Bluetooth-enabled
- Assist in the prevention of vehicle breakdowns and the optimization of the performance of your battery Information regarding the charge of your battery that is simple to grasp
- There is a free app accessible to download
- A full battery management system may be created by connecting many monitors to your phone. Car, motorbike, and starting batteries with capacities of 4.5AH or above are suitable. Compatible with Android operating systems 4.4 and higher, iPhone operating systems 7 and higher, and Bluetooth 4.0. If your battery’s charge falls to a dangerously low level, a push message is issued to you. A two-year warranty is provided.
One (1) battery sense monitor cable and eyelet terminals are included in the kit price. There are no installation instructions available. There are no questions at this time. You may be the first one to pose the question.
A&A Auto Stores – CTEK Chargers CTX Battery Sense 40-149 Battery Monitor
This CTEK Chargers CTX Battery Sense Battery Monitor may be used with any lead-acid battery that has a voltage of 12 volts. USD $0.00 as a subtotal Prop 65 is currently out of stock. Caution is advised when using this product because it may expose you to chemicals such as lead and lead compounds, which are known to the State of California to cause cancer and/or birth defects or other reproductive damage. For further details, please see. BATTERY SENSE, the first-of-its-kind Bluetooth-enabled smart monitoring gadget from CTEK, allows you to easily monitor the status of your powersport vehicle battery.
Using the CTEK Battery Sense App in conjunction with the CTEK Battery Sense Monitor, the CTEK Battery Sense App can assist you in learning all you need to know about your vehicle’s battery state right in the palm of your hand.
The Battery Sense unit’s readings are presented in an easy-to-understand manner in order to aid in the monitoring of a battery’s performance and state. The App displays the battery’s charge status (represented by the percent reading), voltage, and temperature.
CTEK 40-149 CTX Battery Sense Monitor works w/ Android & Apple Phone
Shipping to the following countries: United States, Mexico, Germany, Japan Except for Alaska/Hawaii and US Protectorates, APO/FPO addresses, Africa, Central and South America, Middle East, South America (excluding China and Korea), Russian Federation (excluding Albania, Andorra), Austria (including Belarus), Belgium (including Bosnia and Herzegovina), Bulgaria (including the Republic of), Cyprus (including the Czech Republic), Gibraltar (including the Republic of), Greece (including Guernsey), Hungary (including Iceland), Jersey (including Latvia), Liechtenstein (including