CV boot replacement cost? (Professionals recommend)

A completely failed CV joint will not transfer power to the wheels, and the vehicle will become stranded. The average price for a CV boot replacement starts around the $120 mark and can extend to $300+ depending on your vehicle and transmission type.

  • Replacing a CV boot (which is most cases means replacing the axle/shaft) can cost $150-$600, depending on the make, model and type of vehicle, although on some large or luxury vehicles it can cost $600-$1,200 or more. Sometimes a boot and half-axle will be replaced only on one side, but often they are replaced in pairs.

How much does it cost to replace CV boot?

Typical costs: Replacing a CV boot (which is most cases means replacing the axle/shaft) can cost $150-$600, depending on the make, model and type of vehicle, although on some large or luxury vehicles it can cost $600-$1,200 or more.

Is it OK to drive with a torn CV boot?

It is possible to drive a car with a torn CV boot, but doing so will likely lead to further damage that will eventually require more extensive repair. Among the indications that a CV joint or axle has been damaged is a clicking or popping noise when turning, or vibrations at highway speeds.

Can you replace just the CV boot?

The Constant Velocity (CV) boots cover the CV joints and protect them from outside debris. If no noise is present and only the CV boot is broken, you can replace just the CV boot. Tip: Before you install a new axle, check the CV joints (even when the boot is broken) and see if they are worth saving.

What are the symptoms of a bad CV boot?

4 Signs of a Bad CV Axle/Half Shaft

  1. ‘Clicking’ Noises When Turning.
  2. A Knocking Sound.
  3. Grease on the Inside or Edge of the Tires.
  4. Vibration While Driving. This is a tricky one, since there are many things that could cause vibration when you drive.

Are CV boots expensive?

Cv joints are not particularly expensive items to buy and can range from as little as £20 up to roughly £150. Depending on the car, the labour charge to fit them shouldn’t be that much either. Bank on half an hour to an hour per side to replace.

How urgent is a bad CV joint?

If a CV joint begins to fail while driving, your car will start to pull to one side as one wheel loses power. If possible, slowly steer your car off the road and then call a tow truck. Failing CV joints pose a serious risk so be sure to get your car into your auto shop as soon as possible.

How much does replacing a CV joint cost?

A CV joint itself can cost between $95 and $210. Hiring a mechanic to perform a replacement will be between $165 and $800. The price mainly depends on whether you’re replacing a double or single axle.

How long will a ripped CV boot last?

There is no real set time how long the bad joint will last, and it may last a year or a month. A YourMechanic technician can travel to your location and help and replace the axle CV joint boot as soon as possible.

How hard is it to replace a CV boot?

replacing both sides shouldn’t take any more than 4 hours. have your manual with you, you’d probably need to undo the cv lock nut, separate complete hub assembly from the strut, pull the cv out.

Are CV boots universal?

Unless noted, all CV boots are ‘vehicle specific’. Ones that are designed to fit any vehicle are noted on the product page as ‘universal fit’. And if you can’t locate boots for your specific vehicle, we’ve got the universal-fit CV Boot by RCV Performance.

Can I replace a CV joint myself?

You absolutely can replace your CV axle at home, but you’ll need to be at least remotely comfortable using a jack, jack stands, and power tools. Assuming you have most of the equipment already set up in your garage at home, the cost to replace your CV axle will be quite reasonable.

How long can you drive with a damaged CV joint?

Let’s get down to the answer. The answer will be relative from one CV axle to another. It could take weeks, months, or years. But the average lifespan of a bad CV axle is around five to six months.

Why do my CV boots keep tearing?

The most common cause of CV joint failure is from the deterioration and splitting or tearing of the rubber CV Boot. Once split the protective CV joint grease escapes and dirt, road grime and water can enter the joint and cause the CV joint to wear rapidly and fail prematurely.

Average CV Joint Replacement Cost 2022 – Price Table & Guide

The CV joint in your automobile performs the role of connecting the tires to the gears, and the two most common factors that cause it to malfunction are excessive wear and tear and a lack of lubrication in the joint. Not only is a lack of lubrication one of the most common reasons of CV joint breakdown, but it also often indicates the presence of a possible leak from the boot, which may be quite dangerous. This situation almost often necessitates a complete axle shaft replacement, which is the most recommended and finest option.

What is the average cost to replace a CV joint?

The cost of replacing a CV joint will most likely be the same as the cost of replacing an axle shaft, but the total cost will vary depending on whether you’re replacing one or both of these components. For as little as $86 to $200, you may get a replacement axle shaft, whereas components and labor combined might cost anywhere from $150 to $750. It can cost twice as much as a single axle replacement service, ranging from $150 to $350, whilst the cost of the components coupled with labor can range from $250 to $1,350 for a double axle repair.

CV Joint Replacement Cost Comparison

In most cases, the overall expenses associated with replacing a CV joint are heavily influenced by the type of vehicle you drive and whether it is a single or a double replacement. It is possible to acquire the components needed for the job yourself, but it is recommended that you have a professional do the actual repair since the CV joint is a critical component of your vehicle’s performance, and you don’t want to take any chances with its operation. It is possible to observe in the table below that the cost of CV joint replacement varies based on the type of service provider you pick, and this is also true when it comes to the pricing of the various components included in the procedure.

Walmart

$300 (150 dollars for parts and 150 dollars for labor)

Firestone Complete Auto Care

CV joints are critical components of the actual axle shaft and are located near to the boot and grease reservoir. The axle shaft, also known as a ‘CV axle’ or a ‘half-shaft,’ is responsible for connecting the tires of your automobile to the gears in the gearbox. It is made of steel and has a diameter of around 1 inch. As a result, one end of the axle shaft is connected to the gearbox, while the other end is connected to the wheels. To move the automobile, the gearbox must gently spin the shafts in order for them to be able to turn the wheels, which is accomplished by the use of the clutch.

Due to the evaporation of grease, the CV joint is left dry, and this deficiency in lubrication will result in dirt and debris being drawn into the joint, which will increase wear and tear even more.

Not only is changing the half-shaft a simple and uncomplicated job, but it will also save you a significant amount of money in labor charges.

In most cases, four-wheel-drive cars have two half-shafts up front and two in the rear, but replacing all of them would set you back a significant amount of money. Most of the time, only one half-shaft has to be changed, which makes it a very economical and simple procedure to complete.

How important is the CV Joint Replacement

When the CV joint in your automobile begins to fail, it will have an impact on the amount of power that is transmitted to the tires. The first sign that your automobile is lacking lubricant is when it begins to produce loud clicking noises every time you crank the steering wheel or brake pedal. However, if you replace the CV joint or the entire axle, this problem will be resolved promptly and completely. The CV joint and the axle shaft on the majority of vehicle types may last for an extremely long period of time without suffering any issues.

Although extremely unusual, it is conceivable for the outer joint to physically disintegrate while you are driving your automobile, at which time you would no longer be able to operate your vehicle.

When Should You Repair the CV Joint?

When there is an issue with the CV joint or axle, there are a few signs that you will undoubtedly notice. For example, when an axle begins to malfunction, it will often begin to make a loud clicking sound, which is usually indicative of a lack of lubrication. Additionally, a car that rattles while you accelerate might indicate damage to the CV joint or perhaps the driveshaft, depending on how your vehicle is designed. While CV joint dysfunction might show as steering problems, the majority of the time, this is caused by problems with the driveshaft.

In addition, if you notice grease covering the wheels of your automobile, this might be an indicator that you have a leaky boot, which should be addressed right away by you.

You should seek CV boot repair as soon as possible if you notice an oil-leaking boot on your vehicle.

In order to avoid losing control of your wheels while driving, we recommend that you have your vehicle inspected by a professional as soon as you observe any of the indicators listed above.

What is Done During a CV Joint Repair?

In order to determine what symptoms the automobile is displaying, the technician will evaluate the vehicle. If the vehicle displays evidence of axle damage, the mechanic will most likely replace the complete shaft rather than just the individual pieces. If the axle is defective, the technician will immediately replace it with a new one after lifting the wheels off the ground. If the axle is in good working condition, the mechanic will not charge you a dime for the service. Just before reinstalling the wheels on the vehicle, the mechanic will twist the fasteners to ensure that they are torqued to the proper standards by the vehicle manufacturer.

The good news is that, despite the fact that it is a substantial repair, an axle replacement is a simple and basic procedure.

However, if your automobile has numerous broken axles and CV joints, it may take a little longer to fix and will almost certainly cost a lot more money as a result of the increased complexity.

How to Save Money on a CV Joint Repair?

When fixing your car’s CV joint, the quickest and most cost-effective approach to save money is to replace the complete half-shaft rather than going through the laborious operation of repairing the CV joint, which would take longer and cost more money. The option of a full axle replacement will be recommended to you by any competent technician, and if they do not recommend it and instead propose CV joint repair, you should absolutely inquire about the alternative, which is CV joint repair. Axle shaft replacement is one of those jobs that you should leave to the professionals, even if you have previous experience replacing car parts.

Find a mechanic online, in person, or by phone if you aren’t sure where to start looking.

You may do this by going to Google and typing in relevant phrases such as ‘axle seal replacement cost,’ ‘axle repair cost,’ or ‘axle replacement cost.’ Within a short period of time, you’ll locate a reputable local repair company that will do the task for you without charging you an arm and a leg.

How Much Does It Cost to Replace a CV Joint?

Below you will find a list of CV joint repair quotes that are based on the most prevalent automobile models in the United States. For example, in the first table, you’ll find the typical cost of an axle replacement for one of the wheels, which might be either in rear or in front of the vehicle (front axle seal replacement cost). The second table shows the cost of replacing a double CV axle, which can be used for either the front or rear wheels. The cost of replacing all the axles in a 4-wheel drive vehicle can easily exceed the average cost listed in the second table if you have a vehicle with four wheels drive.

CV boot replacement cost

When the CV boot on your vehicle breaks, all of the grease pours out, and road grit and water enter the joint, eventually causing it to break down. As a result, the CV boot must be changed as soon as the rip is discovered. Previously, shops would only repair the boot, but these days they would often replace the complete axle with a rebuilt unit that includes rebuilt joints as well as a new inner and outer boot to ensure a proper fit. Although a rebuilt axle is more expensive than new boots, rebuilding the complete axle saves a significant amount of work.

See also:  Replace a car battery the right way? (Professionals recommend)

When comparing the cost of CV boot replacement with the cost of a whole axle replacement, the following is how it works out.

What is a CV Joint, exactly?

Read further: CV boot replacement cost? (Professionals recommend)

CV boot replacement cost when replacing just the boots on one axle

If you only do the boots, there aren’t any advantages. Even so, you end up with repurposed CV joints. In the event that you consume and operate on road grit for an extended period of time, you may end up having CV joints that are worn out. In this case, the cost of labor to remove and replace an axle on a 2012 Chevrolet Malibu. 5-hrs Removal and replacement of both the inner and outer CV joint boots will incur labor costs.

1.5 The cost of the parts. Boots, both inner and outer, are $85.00 apiece. New axle nuts (one-time usage) are available for $22. Labor 2-hours work at a rate of $110 per hour = $220 The cost of the parts is $192. The total cost was $412.00.

CV boot replacement cost when replacing the entire axle on one side

In this case, the cost of labor to remove and replace an axle on a 2012 Chevrolet Malibu. 5-hoursCV Axle components are expensive. A completely new AC Delco axle costs $325. (Warranty 24 months, unlimited mileage) Axle Rebuilt by Cardone Inc. (Lifetime Warranty) $175

Can you replace a CV boot yourself using a CV split boot kit?

See this post by 2020 Rick Muscoplat for more information. Rick Muscoplat posted a blog entry on

The Complete CV Joint Replacement Cost Guide

The CV joint in the axle shaft is responsible for connecting the wheels of your automobile to the gears, and it is normally only damaged or fails due to a lack of lubrication or excessive wear. The most prevalent cause of CV joint failure is a lack of lubrication, which is usually indicative of a problem with the boot’s grease leakage. Because it is the most cost-effective and easy method of dealing with a malfunctioning CV joint, a complete replacement of the axleshaft will be advised in the great majority of situations.

Replacement axle shafts may be obtained for between $96 and $214 each unit, while the total cost of the project, including components and labor, can range from $168 to $799.

The cost of parts can range from $149 to $399, while the cost of parts plus labor can range from $235 to $1178, depending on the amount of work needed in the project.

Replacement CV Joint Cost Comparison

In addition to the type of vehicle you drive and whether you require a single or double replacement, the overall cost of CV joint replacement will be determined by the number of joints that need to be replaced. The components themselves may be obtained online from most major stores, but the repair itself is best completed by a qualified technician because it is a critical component in the overall operation of your vehicle’s performance.

Your Mechanic

Replacement Type Work Warranty Price
Single PartsLabor 12 months $190 – $327
Double PartsLabor 12 months $352 – $620

Midas

Replacement Type Work Warranty Price
Single PartsLabor 12 months $214 – $424
Double PartsLabor 12 months $390 – $799

NAPA

Replacement Type Work Warranty Price
Single PartsLabor 24 months $168 – $614
Double PartsLabor 24 months $235 – $1178

Pep Boys

Replacement Type Work Warranty Price
Single Parts 6 Months $96 – $143
Double Parts 6 Months $187 – $276

Walmart

Replacement Type Work Warranty Price
Single Parts Limited $80 – $168
Double Parts Limited $149 – $318

Amazon

Replacement Type Work Warranty Price
Single Parts Limited $91 – $214
Double Parts Limited $171 – $399

What Is The CV Joint?

CV joints are a component of the axle shaft, together with the shaft itself, the boots, and the oil that coats them. Axle shafts, sometimes known as ‘half shafts’ or ‘CV axles,’ are components of a vehicle’s transmission that connect the wheels of the vehicle to the gears of the gearbox. The axle shaft is connected to the gearbox at one end, and the wheels are attached to the other end of the axle shaft. The gearbox spins the shafts, which in turn enables the wheels to revolve and the automobile to drive forward as a result of the rotation.

It is impossible to maintain sufficient lubrication of the CV joint without the use of grease, which allows dirt and other debris to enter the joint and eventually cause it to wear out.

It’s a far more basic fix, and you’ll save money on labor costs in the long run because the turnaround time is significantly quicker.

In a four-wheel-drive vehicle, there will be two in the front and two at the back, making it a costly endeavor to replace them altogether. The majority of the time, only a single axle shaft will need to be changed, making it a less complicated and less expensive issue to resolve.

Benefits of CV Joint Repair

An incorrectly functioning CV joint can result in a variety of problems with your vehicle, including a reduction in the amount of power available to the wheels. It is the most typical problem with a CV joint because it does not have enough lubrication, which results in a loud clicking noise when you are turning. CV joint repair or complete axle replacement might assist to alleviate this problem. The axle shaft and CV joint on the majority of automobiles should endure for an extended period of time without experiencing any serious problems.

In the worst-case situation, the outer CV joint may fail while you’re driving, rendering the vehicle immobile and unable to be operated.

When Should You Have The CV Joint Repaired?

There are various telltale signals that there may be a problem with the CV joint or the axle in general that you should be aware of. A defective axle will typically create a clicking or clunking noise while you’re driving, which is mainly caused by a lack of lubrication in the axle. If you experience any vibrations when accelerating, this might potentially indicate a problem. While this might indicate a problem with the driveshaft, it could also indicate a problem with the CV joint, depending on the architecture of your vehicle.

If there is an issue with the axle shaft, you will most likely hear a loud clicking noise when you are turning a corner.

This is symptomatic of a leaky boot, and it will be necessary to fix it as soon as possible.

Having your car’s power to the wheels fail may be a dangerous situation, so if you observe any of these signs, you should get professional assistance as soon as possible.

What Is Done During An CV Joint Repair?

  1. If the automobile is displaying indications of axle deterioration, the technician will most likely recommend replacing the entire shaft rather than the individual components
  2. However, this is not always the case. The mechanic will often begin by lifting the wheels off the ground and removing the wheel from the vehicle. If the axle is determined to be problematic, the technician will replace the entire part with a new one, saving you money. To ensure that all of the fasteners are torqued to the proper factory specifications, the wheels will be reinstalled on the vehicle
  3. Before a road test is done to evaluate whether or not the repair was successful, the tire pressure will be checked to ensure there are no problems. Despite the fact that it appears to be a significant repair, changing the axle on a single wheel should not be a time-consuming endeavor. The repair of your vehicle may be more time-consuming (and more expensive) if you have many failed CV joints or axles.

How to Save Money on CV Joint Repair

In order to save money on CV joint repair, the most cost-effective option is to simply replace the half shaft itself rather than having rather complex repairs performed on the joint itself. Because most mechanics would propose this as usual procedure, it’s a good idea to ask about the cost of axle replacement if you’re quoted for joint repair. While it is possible to conduct the repairs on your own, the axle shaft is a critical component of the vehicle, and it is best left to a professional if you are not completely sure in your abilities.

Taking the time to compare quotes may save you money.

Sample CV Joint Repair Costs

In order to give you a better understanding of the cost of CV joint replacement, we’ve gathered some quotations from some of the most prevalent automobiles on the road in the United States. For example, the first table displays the prices for a single axle replacement, which will be for a single wheel that will be either in the front or back of the vehicle. The second illustration depicts the cost of double axle repair, which may be performed on either the front or back of the vehicle.

Axle shaft replacement costs around twice as much for 4 wheel drive cars, however this is an uncommon occurrence due to the high expense of replacing all four axle shafts in one go.

Single

Model Labor Parts Total
Ford F-Series $79 – $100 $134 – $427 $213 – $527
Chevrolet Silverado $118 – $151 $178 – $351 $296 – $502
Ford Focus $126 – $161 $136 – $362 $262 – $523
Toyota Camry $197 – $251 $164 – $592 $361 – $843
Toyota Corolla $205 – $261 $164 – $575 $369 – $836
Nissan Altima $197 – $251 $164 – $617 $361 – $868
Honda CR-V $87 – $110 $164 – $585 $251 – $695
Honda Civic $94 – $121 $164 – $578 $258 – $699
Honda Accord $94 – $121 $164 – $318 $258 – $439
Ford Fusion $118 – $151 $287 – $463 $405 – $614

Double

Model Labor Parts Total
Ford F-Series $134 – $171 $268 – $854 $402 – $1025
Chevrolet Silverado $220 – $281 $356 – $702 $576 – $983
Ford Focus $189 – $241 $272 – $724 $461 – $965
Toyota Camry $394 – $502 $328 – $1184 $722 – $1686
Toyota Corolla $252 – $321 $328 – $1150 $580 – $1471
Nissan Altima $213 – $271 $328 – $1234 $541 – $1505
Honda CR-V $173 – $221 $328 – $1170 $501 – $1391
Honda Civic $189 – $241 $328 – $1156 $517 – $1397
Honda Accord $189 – $241 $328 – $636 $517 – $877
Ford Fusion $220 – $281 $574 – $926 $794 – $1207

CV Joint Costs Submitted By Our Users

Compare your quotation to that of other people from all across the country to ensure that you are receiving the greatest value possible. The average cost of a CV Joint is $531 dollars.

Loading Chart.

The CV joint, in conjunction with the CV axle, is responsible for transmitting the engine’s power via the gearbox and out to the vehicles’ wheels. CV axles were first employed exclusively in front-wheel-drive cars since both front CV axles transmitted power to the wheels and were engineered to be able to transmit torque at extreme angles, such as while maneuvering or hitting bumps. In recent years, with the increasing popularity of all-wheel-drive vehicles and independent suspension, CV axles (and joints) have found their way into trucks, SUVs, and all-wheel-drive automobiles, often in both the front and rear axle configurations.

A CV axle is made up of two CV joints.

Because CV joints are subjected to a harsh environment, including exposure to road salt, water, dirt, and filth, these boots frequently fracture and fail, particularly along the ribs of the ‘accordion.’ It is at this point that the grease that maintains this joint lubricated begins to leak out, resulting in the joint finally failing.

Over time, the cost of new CV axles that were mass-produced became a more cost-effective alternative to merely replacing the joint since the axle was ready to be installed, saving both time and money compared to simply changing the joint.

CV Axle Replacement Expenses

Replacement axle shafts may be purchased for between $60 and 150.00 apiece, and labor to change them takes between 1.5 and 3 hours, putting the total cost of labor to between $150 and 350.00. Replace a CV axle on your own is a somewhat difficult procedure that necessitates the use of specialized equipment, all of which may be leased for free via AutoZone’s loan-a-tool program. If you have experience with brakes, struts, or other undercar repairs of a similar kind, you should have no trouble doing a CV axle replacement without difficulty.

If you want assistance with the repair, you should contact one of our Preferred Shops in your region who can provide assistance with the repair.

What Are the Symptoms of a Bad CV Joint?

Before you get concerned about the expense of a CV axle replacement, pay close attention to the symptoms that you require one in the first place. In the event that your CV joint is having problems, there are a few signs that will alert you to the fact that you have a problem. Keep an eye out for any of these symptoms, as they will serve as an excellent sign that anything is wrong with the CV joints in your automobile or truck.

See also:  BAS, What is a brake assist system? (Solution)

Noises when Turning

Noises such as popping or clicking, especially when turning, are a telltale indicator of a problem. It will pop and click as the joint wears down, especially if there is no lubrication present.

Cracks on the Boot

Whenever you do an oil change, thoroughly inspect your CV boots by opening up the ribs of the ‘accordion’ and checking for cracks. Check for traces of oil around the joint if you have a broken boot. A damaged boot will spew grease everywhere it can. If you see any, it’s only a matter of time before the joint gives out completely and collapses.

Wobbly Axle

A CV joint that is deteriorating will wobble and become unbalanced. As a result, if the wobbling occurs while you press on the gas pedal, it becomes immediately apparent since the engine torque causes the axle to wobble. While under the car, you can typically determine which axle is causing the wobbling by holding the axle at the joint on both sides and pushing up and down, as well as side to side, while under the vehicle. If there is any slop or movement in the axle, the axle should be considered faulty.

Bouncing or Vibrations

Bouncing is frequently a step worse than vibrations, and the automobile should not be driven at this stage. The axle, if it fails fully and breaks, can become a whirling projectile that can cause damage to other components in its path, such as the exhaust system, struts, and brake lines. It’s not worth taking a chance.

How Long Can I Go with a Bad CV Axle?

To put it another way, it is dangerous to drive with a faulty CV joint on one of the axles. If you notice that your car is exhibiting any of the symptoms of a faulty CV joint, the best thing you can do is take it to a technician as soon as possible or get the joint itself replaced. You should keep in mind that if the CV boot is ripped, it is just a matter of time before the axle gives up. Failure to solve the problem can result in catastrophic failure of the axle, which, as previously indicated, is a component that is in a condition of rotational movement.

The most effective approach of preventing CV joint / axle failure is to examine the joint often.

In most cases, it is not part of a standard inspection, but when they are under the car, it takes less than 2 minutes to thoroughly check each one.

Visit your local AutoZone for answers to more specific issues or for advice. Our knowledgeable specialists will be happy to assist you with any of your problems!

How Much Does Replacing a CV Boot Cost?

DIY: $5-$150+ Parts Average Professional Install: $150-$600 Large/Luxury vehicle: $600-$1,200+
When a CV boot is cracked, torn or simply fails due to age, it’s difficult to determine how long it has been compromised and how much damage has been done to the CV joint. In some cases a repair shop will simply replace the CV boot, but typically the entire CV axle will be replaced with a new or remanufactured axle, because the costs are about the same and the shop might not be willing to guarantee the work unless the entire axle is replaced.Typical costs:
  • Replacing a CV boot (which in most cases entails replacing the axle/shaft) can cost between $150 and $600, depending on the make, model, and type of vehicle
  • However, on certain big or luxury cars, the cost can be as high as $600 to $1200 or even more. Occasionally, a boot and half-axle will be changed on only one side of the vehicle, but more frequently, they are replaced in pairs. When it comes to passenger automobiles, CostHelper users report spending between $165 and $300 to repair one axle and boot, with an average cost of $228
  • Or between $218 and $510 to replace both axles and boots, with an average cost of $414. CostHelper users report charges ranging from $137 to $300 to do one side of an SUV or minivan, with an average of $219
  • Or from $330 to $1,258 to do both sides, with an average of $577. A do-it-yourself CV boot kit can range in price from $5 to $30, depending on the make, model, and kind of vehicle, and the process takes around three to four hours to complete on average. A replacement CV axle can range in price from $50 to $150 or more, depending on the vehicle, and the project takes around 30 minutes. Our customers report spending between $12 and $23 for DIY replacement of simply the CV boot, or $100 for two CV axles with boots, for an average DIY cost of $45 per axle. Depending on the year, make, and model of the vehicle, Rocky Mountain Driveline in Denver, CO, offers a CV axle pricing list with costs ranging from $50 to $70 for the part alone
Related articles:Tune-up,Replacing a Transmission,Replacing a Clutch,Tires,Flushing a Transmission
What should be included:
  • A constant velocity axle delivers power from the engine and gearbox to the wheels of the vehicle, allowing the axle to flex in response to the car’s suspension while maintaining the ability to move the wheels. Two joints make up each CV axle, and each joint is protected from dirt and moisture by a CV boot that wraps around it. Colorado’s Rocky Mountain Driveline presents an overview
  • CV joints are found in the majority of front-wheel drive cars and some rear- and four-wheel drive vehicles, among other things. Using a video by Eric the Car Guy, you can learn how to repair a CV boot, as well as why it is more cost effective to replace the entire axle rather than just the boot alone.
  • Some companies include the cost of a wheel alignment ($20-$400) in the price of a CV boot/axle replacement, while others charge an additional fee for this service. It is not always necessary to have a wheel alignment performed following a CV boot/axle replacement, but it is possible that the conditions that produced the CV boot/axle difficulties had an impact on the alignment.
  • Some repair companies provide discounts to AAA members
  • However, this is not always the case.
  • Using the National Institute for Automotive Service Excellence or the International Automotive Technicians Network, you may identify nearby auto repair companies
  • Consumer Reports offers advice on how to choose a reputable mechanic.
CostHelper News
What People Are Paying – Recent Comments
Page 2 of 2-Previous12
Posted by:Trying2keepfrmgettingrippedoff in Dawsonville, GA. Posted:December 27th, 2021 08:12AM
Car Make:2002 Ford Car Model:F150
Auto Shop:Express Oil Change
didn’t take here but wanted to charge $200 for part (boot and axle for one side)rest is labor. Ended up taking to local auto shop for $250
Posted by:DIY amature in Chantilly, VA. Posted:June 12th, 2020 07:06PM
Car Make:Honda Car Model:Odyssey
Auto Shop:DIY
price incl Kobalt 24V Max 650 lbs. ft. torque impact driver, 36 mm impact socket (Amazon), 250 lbs. ft. torque wrench (Amazon, EPauto), Lowes: Pry bar set. DIY instruction/demo video on Youtube. Already had other sockets and hand tools such as nail punch, hammer at no cost for this repair job.
Posted by:Jay Prince in Grand Rapids, MI. Posted:December 12th, 2019 01:12PM
Car Make:2006 Car Model:Honda CR-V
Auto Shop:Muffler man
Posted by:Tullysan in SAN Francisco, CA. Posted:October 24th, 2019 12:10AM
Car Make:Mini Car Model:Cooper s
Auto Shop:Mini Stevens creek
I think I got you guys all beat in terms of dealerships ripping people off. On top of that I have a CPO warranty that i heard most people have it covered by. I was just doing my research before I accepted charges. Now I know this is way to high. I hate being seen as a naive girl, mechanics always try and rip me off.
Posted by:SLO in Bensenville, IL. Posted:April 30th, 2019 02:04PM
Car Make:Subaru Car Model:2003 Outback
Auto Shop:Grand Subaru
I always feel that they charge way more than any other place, but they use genuine parts, which is usually a plus. I’ve had to get jobs done a second time when I’ve taken my car elsewhere where they use whatever they have in stock. Had a dealership coupon which was helpful, $30 off.
Posted by:DangerousCurveAhead in Sunnyvale, CA. Posted:February 4th, 2019 08:02AM
Car Make:VW Car Model:Eos 2007
Auto Shop:VW Sunnyvale
Both outer boots. Quoted about $350 each. Wish I had the time to take it to shop around like esyriac did.
Posted by:Nancy22 in Charlotte, NC. Posted:June 2nd, 2017 06:06PM
Auto Shop:Woodie’s
Scott Clark Toyota quoted $1100.00 to replace one axel and boot on 2012 Toyota Camry LE so called around and the average was $400. Woodie’s has 36,000 mile warranty on parts and labor and was $300.
Posted by:Frank Topolski in Bernardsville, NJ. Posted:February 7th, 2017 06:02AM
Car Make:Audi Car Model:A 3
Auto Shop:Flemington Audi
Told that the CV boot was leaking and the axle had to be replaced. I believe that the cost is way too much and have opted not to do the work,at least at the Audi dealer.
Posted by:Winker in Concord, CA. Posted:January 5th, 2017 05:01AM
Car Make:96 Car Model:Camry
Auto Shop:Midas
Went in for bad brakes was told cv boots should be changed paid $870. 2 days later cars.drivinggoes into neutral no gears workingdriver side arm is coming out of enginerattled lose.
Posted by:Stanav in Boston, MA. Posted:October 3rd, 2016 12:10PM
Car Make:Honda Car Model:Accord
Auto Shop:Honda dealer
I had both drive shafts (left + right) replaced along with the 2 front wheel bearings for a total cost of $1150. I think I was ripped off by this Honda dealer.
Posted by:fujiwaraneil in Pearl City, HI. Posted:January 13th, 2016 05:01PM
Car Make:Maxima Car Model:Nissan
Auto Shop:76 Station in Pearl City
Needed the CV boot replaced in order to pass Safety Inspection, since I was getting the Safety done there I went with them for the repair also. Fast job, cost was exactly as quoted but I didn’t shop around so I didn’t know if that was cheap or not. PS you need to update the website to include 2016 as an option.
Posted by:Subbie Giy in Concord, CA. Posted:August 30th, 2015 09:08PM
Car Make:subaru Car Model:forester
Auto Shop:mobile mechanic
Bought the axles myself on ebay for 40 each, then had a mobile mechanic come to my house to do the work. It is not a hard job, but has a couple tricky parts for a subaru. Easier for a honda or toyota.
Posted by:Raymondp in NEW YORK, NY. Posted:August 24th, 2015 12:08PM
Car Make:TOYOTA Car Model:COROLLA
Auto Shop:MOBIL / UTOPIA/ NORTHERN
Replaced both left and right cv axles and boots total cost 350.00 including parts labor and tax
Posted by:Albe in North Aurora, IL. Posted:July 1st, 2015 04:07PM
Auto Shop:Gerald Nissan, North Aurora, IL
I definitely think they charged me way too much for labor based at the prices I see here. Nissan Rogue 2008. Why me?$$$$$$
Posted by:kakeladi in Visalia, CA. Posted:May 28th, 2015 03:05PM
Car Make:Ford Car Model:2004 Escape
I have been quoted $600 per side to replace axel with boot. No way do I have that kind of $$. Just how important is it that they be replaced NOW? I was told one thing on the phone and another on the print out. On the phone I was told the boots were torn. The print out says the boots are hard from age.
Posted by:renee singh in Sacramento, CA. Posted:April 22nd, 2015 11:04PM
Auto Shop:Lews Automotive, Santo, ca
Posted by:Nancy1120 in Las Vegas, NV. Posted:February 24th, 2015 10:02AM
Car Make:hummer Car Model:h3 alpha
Auto Shop:sun auto
I think they greased me. $184.96 parts$300.06 labor$500.00total toooo much!
Posted by:JamieP in Hillsboro, OH. Posted:June 12th, 2013 12:06PM
Car Make:Pontiac Car Model:G6
Auto Shop:Tire discounter s
Had a hole in the boot and no grease. They fixed axle and boot
Posted by:zoologychic in Mountain View, CA. Posted:May 22nd, 2013 08:05PM
Car Make:2004 VW Car Model:Beetle
Auto Shop:Advanced Automotive Repair, Inc
Posted by:a user in Oklahoma, OK. Posted:January 8th, 2013 02:01PM
Auto Shop:Central Mercedes in Ok
I don’t know the price are right or what, I remember the rebuilted CC axle only cost 75$ a piece for 2 it run $ 150 plus labors. I estimate it’s for $ 400 is the Max. I am got bending over bad. Well only one time.I bet u never again.
Posted by:JME B in Woodstock, GA. Posted:January 4th, 2013 07:01AM
Car Make:Honda Car Model:2006 CRV
Auto Shop:Hennessy Honda
They said that the CV boot was cracked and the oil was leaking onto the Axle, If it continued I would have to replace the Axle too.
Posted by:esyriac in SAN JOSE, CA. Posted:December 30th, 2011 11:12AM
Car Make:VW Car Model:PASSAT 2.0 2006
Auto Shop:Dave’s German Auto San Jose
Both cv boots replaced at 60K miles. The dealer was quoting me 650$ for both. Got it replaced at a local shop.
Posted by:Ewa212 in Flushing, MI. Posted:December 29th, 2011 02:12PM
Car Make:Chevy Car Model:2003 Malibu LS
They had have to replace my CV half shaft and are doing it at a responsible price. I’m not going to have my car for a couple of days but thats okay bc they are including an alignment and tire balance for me in the cost. Also the mechanic is going to look my entire car over to make sure I don’t need anything else done. I can’t remember the name of the shop but the guys there are really nice they even paid to have my car towed to the shop for me:)
Posted by:Goldmaster in Pensacola, FL. Posted:November 21st, 2011 08:11AM
Car Make:ISUZU Car Model:TROOPER
Auto Shop:FIRESTONE COMPLETE AUTO CARE
The cost estimate provided me to replace both half axles was 1257.86 here in Springfield, VA. I costed out the parts and will do the job myself after watching utube videos!
Posted by:Rikky in Kenilworth, NJ. Posted:November 15th, 2011 07:11AM
Car Make:Honda Car Model:Accord
Auto Shop:Getty – Kenilworth, NJ
Left outer boot cracked and spewing grease. Replacing outer and inner boots for a very reasonable price due to low labor costs.
Posted by:addy92 in hope valley, RI. Posted:August 6th, 2011 10:08AM
Car Make:vw Car Model:passat
Auto Shop:diy
purchased cv boot kit from napa and pulled axle out to replace boot took about two hours
Posted by:Tanny in Norfolk, VA. Posted:February 3rd, 2011 06:02PM
Car Make:Bmw Car Model:X5
Auto Shop:Kramer
I paid 435 for the part an labor. Was that a good price or was that Geat price?
Posted by:pawel in trenton, NJ. Posted:January 27th, 2011 06:01PM
Car Make:Kia Car Model:optima
i did it my self its not worth paying 500 or 600 hundred of dollars i was doing this first time and it wasent too hard just alot of stuff you have to remove
Posted by:Jabazi in Dallas, TX. Posted:January 21st, 2011 10:01AM
Car Make:Honda Car Model:civic
Auto Shop:Ace autocare

More Cars-Related Topics

Check Out All Costs for Cars How Much Does Replacing a Transmission Cost? How Much Do Tires Cost? How Much Does an RV Cost?
CostHelper is based in Silicon Valley and provides consumers with unbiased price information about thousands of goods and services. Our writers are experienced journalists who adhere to our stricteditorial ethics policy.

How Much Should CV Joint Replacement Cost? ❤️

It is possible to detect an issue with the CV joint by looking for many tell-tale indicators, including vibration when the vehicle is accelerating, a loud clicking noise while turning, and grease on the vehicle’s wheels. Repairing several CV joints might cost as much as $1600 in total. Automobile repairs are EXTREMELY EXPENSIVE. Incorrectly functioning CV joints can result in a variety of problems, ranging from clicking during turning to a lack of power supplied to the wheels. Problems with this component are quite prevalent, yet some cars never need to have a CV joint replaced.

  1. One possible explanation is that you are getting older.
  2. After then, certain parts begin to fail, and the cost of repairs can quickly mount up in the thousands!
  3. Although it is unlikely, the outer CV joint may degenerate while you are driving, rendering the vehicle immobile and unable to be driven.
  4. The research process is an excellent place to begin when assessing whether a CV joint is damaged, how it became damaged, or how much it will cost to repair the joint.
  5. Some typical questions concerning CV joints will be addressed in this article, as will indicators that it (they) should be replaced as well as the expenses related with doing so.

What is a CV Joint and What Does it Do?

A Constant Velocity joint, often known as a CV joint, is used to link the gearbox of your car to the wheels. Each axle has two joints: an inner joint that links the gearbox to the axle and an exterior joint that connects the axle to the wheel. Each axle also has two joints that connect the wheel to the axle. The CV joint travels in any direction in conjunction with the suspension of your car. For the purpose of estimating the cost of CV joint replacement, this information is critical.

Why Do CV Joints Break?

A CV joint is a kind of CV joint. Your mechanic’s notation on your most recent estimate may have left you scratching your head, wondering how this part could have failed so suddenly, especially considering that most automobiles should endure for a substantial length of time without experiencing CV joint problems. When was the last time you heard someone state that they had to take their automobile in for a CV joint replacement? Probably never. It’s not your average routine maintenance, by any stretch of the imagination.

  • A CV joint’s most prevalent issue is when the protective boot fractures or is otherwise destroyed.
  • Because they are subjected to more movement than the inner CV joints, it is common for the outer CV joints to fail first.
  • If you are given a quotation for merely a joint repair, it is worthwhile to inquire about the cost of an axle replacement as an other solution.
  • Some mechanics strive to make their jobs simpler, but this is detrimental to their long-term success.

If CV joint symptoms are present but are disregarded, it may result in a car breaking down on the road. If you are unsure of what to do next, you could consult with a technician or look into the usual signs of CV joint problems.

Signs the CV Joint is Damaged

If you have a damaged CV joint, you will observe the following manifestations:

  • While driving, you may hear a ticking, clicking, or clunking sounds. When you accelerate, you will feel vibrations. Problems with steering
  • Maintain a thin layer of grease on the wheels of your car, particularly around their inner edges. The wheels are losing their ability to turn.

Specific symptoms might assist your technician in determining the source of the problem. Steering troubles, for example, might indicate a problem with the driveshaft; but, if they occur as you are rounding a corner and are accompanied by a loud clicking noise, it is likely that one or more CV joints are malfunctioning. If you detect any vibration while you accelerate, it is possible that you have a problem with a CV joint. It is possible, however, that there is a problem with the driveshaft. The mechanic will take into consideration the arrangement of your vehicle to guarantee that there are no additional concerns.

This signifies a leaky boot that must be repaired as soon as possible.

This is a major problem that might leave you stuck and burdened with the stress and annoyance of contacting for towing service, waiting for towing service, and the expensive expense of towing service on top of the cost of other repairs.

How Long Can I Drive with a Bad CV Joint?

Driving with a damaged CV joint is extremely dangerous and should not be undertaken carelessly. If you are concerned about the expense of CV joint replacement and you are aware that your CV joint is in poor condition, you should avoid driving altogether. Finally, the danger isn’t worth it in terms of financial gain. Many mechanics believe that it will take around six months for the part to completely disintegrate, with variations depending on driving style and when the damage is first seen. This allows the automobile owner a little window of opportunity to complete the repair on a timetable that isn’t too demanding.

  • We don’t advocate doing so.
  • A mechanic can inspect the situation.
  • When a CV joint is significantly worn out, it has the potential to disintegrate while driving, rendering the vehicle undriveable.
  • In order to avoid this, it is not suggested to drive with a defective CV joint (or two).
  • Before you go behind the wheel, check with your technician.

How Much Does It Cost to Replace the CV Joint?

It’s possible that the technician may inform you that more than one CV joint has to be fixed.

This may be a very stressful scenario, especially if one’s finances are in a precarious state. Old automobiles require a lot of maintenance, and they are rarely covered by a recall or a manufacturer’s warranty. A short search on the Internet yields various estimations that are not quite accurate.

  • Depending on the parts, a single axel repair can cost anywhere from $170 to $480, and it can be done on either the front or back wheels of the car. The total cost of the repair ranges from $300 to $1600, depending on your vehicle, the type of axel repair, and where you reside. Customers driving four-wheel drive cars will spend considerably more to have all four axle shafts rebuilt
  • This is especially true for high-mileage vehicles.

CV joint repair costs rise as a result of the differences between each make and model on the market. Not all components are simple to come by or inexpensive once they are discovered. Some repairs, for example, are single axle in nature. Others include double axel, which can be used for either the front or back of the vehicle. It’s possible that you’ll need to have all four axles fixed. It may seem important to spend money on the repair since the risk of driving about town with a faulty CV joint is too great.

Can I Repair the CV Joint Myself?

If you’re a mechanic, professional, or hobbyist with a garage, equipment, and the necessary knowledge, you might be able to repair the CV Joint on your own. If you’re not sure, leave it to the experts. Those axels on the automobile aren’t anything to be laughed at. Using an Internet tutorial will not suffice if you have no prior knowledge of what you’re doing. Take the vehicle to a mechanic as soon as possible. It’s well worth it for the peace of mind. If you’re looking to save a few dollars, it’s a good idea to shop around before completing the repair work.

A junkyard may also be willing to pay you cash for recycling your automobile if you contact them.

Is Fixing a Vehicle with a Damaged CV Joint Worth It?

The answer to this question is dependent on the type of vehicle and the severity of the accident. When it comes to single axle repairs, a broken CV joint is not a significant expense. This little investment of $300 to $650 is well worth the piece of mind that comes with knowing your car is in excellent working order and does not endanger your or others’ safety. In contrast, if a damaged CV joint fails and ruptures, especially while you are driving, it is a whole other situation. When you have a damaged CV joint, zipping about the city is a serious risk.

  1. From a purely financial standpoint, replacing one faulty CV joint for a few hundred dollars is more preferable to paying out thousands of dollars for accidents or damages.
  2. Furthermore, there are additional considerations to take into account.
  3. Is this a car that you use on a daily basis?
  4. When a car is old, the cost of the repair may be possible to be utilized as a down payment for a more dependable vehicle.
  5. It is possible to repair the injured CV joint using alternative methods if this is not an option.
  6. Additionally, you might send the vehicle to a junkyard for parts.

After the car has been stripped of its valuable components, it will be recycled. The tow truck firm will arrive to your location and tow your vehicle directly to a junkyard, where you will be paid in cash.

A Broken CV Joint May Not Be the End of the World

Before pulling into the garage, we secretly pray that there aren’t any costly issues with the automobile. The exorbitant prices of automobile repair have become unaffordable for many people these days. As a result, many individuals choose to drive modern vehicles and to purchase extended warranties. The good news is that if you are faced with a fractured CV joint, you have a wide range of treatment alternatives. If you have the financial means to have the broken CV joint repaired as soon as possible, the cost of the repair is well worth it in terms of safety.

You can use this time to save money in order to pay for the repair.

Keeping your cool is essential if you find yourself with a broken CV joint while driving.

While you’re waiting for towing assistance, look into area mechanics to find out who has the cheapest prices and is available when you need them.

If you determine that the car’s repair is not worth the time and money, call a junkyard to haul the vehicle and your troubles away.

Determine what option will provide you the most comfort and security.

Make sure that your CV joint does not spoil your day.

Leave a Comment

Your email address will not be published. Required fields are marked *