The airbag light, or SRS (supplemental restraint system) light, on the GM dashboard shines whenever there is a malfunction with the airbag deployment system. The vehicle needs inspected and fixed to ensure against accidental deployment of the airbag.
- Cause of GM airbag light on GM has determined that these airbag trouble codes can be caused by interference from an aftermarket USB and/or phone charger plugged into the 12 volt power outlet. The solid-state electronics in the charger can cause excessive airbag loop resistance or varying resistance.
What would cause an airbag light to come on?
The most common cause for the airbag light coming on is that the airbag system is deactivated or turned off. There may be an issue with a crash sensor, SRS module, or other airbag component. Alternatively, the sensor in the passenger seat that determines whether that airbag should be active or not may be faulty.
How do I get my airbag light to go off?
How to Reset an Airbag Light
- Put the key into the ignition and turn the switch to the ‘on’ position.
- Watch for the airbag light to turn on. It will stay illuminated for seven seconds and then shut itself off. After it shuts off, immediately turn the switch off and wait three seconds.
- Repeat Steps 1 and 2 two more times.
What does it mean when your airbag light comes on and stays on?
The airbag light indicates that something is wrong with the seatbelts or airbags. This means that it’s probably not safe to drive with the airbag light on. If it stays illuminated in your vehicle, we recommend having it towed to the dealership rather than driving it yourself.
Will disconnecting battery reset airbag light?
No, this information is stored in non volatile memory. The airbag light is usually on if there’s a problem with the system. Even if you could clear the code which is reporting that, if the problem isn’t fixed then it will just be detected again, and the light will come back on.
Where is the airbag sensor?
An impact sensor is normally fitted to the front of the vehicle as this is where a collision is likely to occur. The sensor is positioned inside the engine and a similar safety sensor is located inside the passenger zone of the vehicle.
How do you reset the airbag light on a Chevy?
Turn Your Ignition on and Off. First, turn the ignition switch on. Next, wait for the airbag light to turn on – it normally stays lit for seven seconds before shutting itself off. Then, immediately turn off the ignition switch, and wait three seconds. Repeat the initial steps once or twice before starting the engine.
Can you reset airbag light without tool?
In some older cars, though, it is possible to reset the airbag light without a scanner by removing the car battery terminals. Check the wiring system underneath the driver or passenger seat for any loose wires or corrosion in the connector plug. Spray the connector plugs with an electronic cleaner and restart your car.
How much does it cost to fix the airbag light?
Number 1 — Reset Airbag Light You’ll need to hire a professional to come in and examine the airbags before you continue to drive the car. This process can take several hours of time and usually costs a few hundred dollars, although depending upon the type of car it may be up to about $600.
How do I know if my airbag sensor is bad?
Symptoms of a failing airbag sensor You can easily tell if the sensor is functioning if the airbag warning light on the dashboard is illuminating every time you start the vehicle. But, if the airbag warning light stays illuminated after starting the vehicle, this is an indication of an airbag sensor problem.
Can low battery cause airbag light?
Another common problem could be a bad ground to the battery that causes warning lights to turn on (including the airbag light). It can if the battery is at 9V or below. Often the light will extinguish after the battery returns to normal voltage.
Can you pass inspection with airbag light on?
It depends on your state requirements if you fail a car inspection with an airbag light on. Although, in general, you’ll want to have your airbags checked right away if you notice this warning light turned on. If your airbag light is on, they may not deploy in an accident, causing you serious injuries or even death.
Is there a fuse for airbag light?
One fuse in particular, fuse #13 is a likely culprit. If your airbag light is on and your rear windshield wiper doesn’t work, then it’s a pretty good indication that you need to change fuse #13 and possibly others. Blown fuses can definitely cause the airbag light to come on.
Will removing airbag fuse?
Most repairs near electrical systems advise removing the airbag fuse and disconnecting the battery, to avoid accidental discharge of the bags. If it’s been removed, replace with the proper style and amperage.
How do you reset the airbag light on a GMC Sierra?
Select ‘ Body Control Module,’ then ‘Codes,’ then ‘Clear All Codes.’ This will [turn off the airbag light](https://itstillruns.com/turn-off-airbag-light-7291521.html) on the GM’s instrument panel. Unplug the computerized scan tool and start the engine. Notice that the SRS light has shut off.
How to Reset GM Airbag Light
Photograph by Christopher Meder for Fotolia.com of a microchipped car key. The airbag light, also known as the SRS (supplemental restraint system) light, illuminates on the General Motors dashboard anytime there is a problem with the airbag deployment system. The car must be examined and repaired in order to prevent the airbag from being accidentally deployed. Using a computerized scan tool that you may obtain from your local auto parts supplier, you can turn off this light, which is controlled by a computer.
Step 1
As soon as you put your key in the ignition, make sure it is in the ‘Off’ position and that your car is in Park (or first gear if it is an automatic gearbox from General Motors). Place your foot on the parking brake.
Step 2
To begin, turn the vehicle’s ignition switch to the ‘On’ position but do not start the engine.
Step 3
Connect the computerized scan tool to the diagnostic port, which is located beneath the driver’s side dashboard, just above the gas and brake pedals.
Step 4
To browse through the menu, press the arrow keys on the scan tool’s front panel. Select ‘Body Control Module,’ then ‘Codes,’ and finally ‘Clear All Codes’ to complete the process. This will appear on the instrument panel of the General Motors vehicle. Remove the computerized scan tool from the vehicle and start the engine. Take note that the SRS light has been turned off. References
- To go through the menu, press the arrow keys on the scanner’s face. Make your way to ‘Body Control Module,’ then to ‘Codes,’ and finally ‘Clear All Codes.’ GM’s instrument panel will display this. Start the engine after unplugging the electronic scan instrument. Take note of the fact that the SRS light has been disabled. References
What You’ll Need to Get Started Biography of the Author Known for her self-published books, Katie B. Marsh also works as an article writer, scriptwriter, and inventor. Eight years after earning her degree in court reporting from South Coast College of Court Reporting, she worked as a congressional and freelance court reporter. Her literary career began in 2005, when she graduated from high school. Her work may be found on several websites, including amazon.com, booksforsharing.com, and ezinearticles.com.
More Articles
Biographical Information about the Author. Inventor and self-published author Katie B. Marsh has written articles, written screenplays, and created inventions. Her eight-year career as a congressional and freelance court reporter began after she graduated from South Coast College of Court Reporting in California. Her literary career began in 2005, when she moved to the United Kingdom from Germany. ezinearticles.com, amazon.com, booksforsharing.com, and other websites host her material. It was in October 2009 that she finished her first script.
What Causes ChevyAirbag Lightto Come On?
The Chevrolet airbag light may illuminate as a result of a variety of factors, including but not limited to:
- Deployed airbags, faulty seat belts, and a damaged crash sensor are all possible causes of low battery voltage produced by a dead battery. The clock spring is broken, and the wiring harness is damaged.
Obtaining error codes from the Supplemental Restraint System (SRS) / airbag system can assist in narrowing down the issue.
How to Reset Airbag Light on a Chevy
Following are instructions on how to read codes from the airbag module and clear them in the proper manner.
In order to complete this operation, you will require a Chevrolet Airbag Scan Tool. It is possible to use a genericOBD-IIscanner and have no fault codes shown even while airbag codes are present and the airbag light is illuminated.
- The Onboard Diagnostics port, commonly known as the OBD-II port, is located under the dash of your Chevrolet vehicle. The video element cannot be shown because your browser does not support it. This port is available on all Chevrolet vehicles manufactured after 1996. Connect your Chevrolet Airbag Scan Tool to the OBD2 port, which has 16 pins. When you turn on the ignition, the scanner will only be able to plug in in one way because the port is trapezoid shaped. Do not turn on the engine. If your Chevrolet is equipped with a START/STOP button, push it without touching the brake pedal. Allow the Chevrolet airbag scanner to come up to full power. When the ignition is turned on or when the shift lever is moved to position II, the scanner should activate. Using the options on the scanner’s screen, pick Chevrolet once it has been completely charged. Follow the prompts on the diagnostic scanner to determine which model you have. Then, manually pick the AIRBAG SYSTEM from the drop-down menu. Continue reading to learn how to interpret codes and how to scan your Chevrolet for airbag trouble codes. If the codes you obtain have a PRESENT or CURRENT state, you will need to correct the problem before you can turn off the airbag light
- Otherwise, you will need to wait until the problem is resolved. If the codes have a state of STORED or PAST, it is safe to clear the code from the system. For example, once the battery has been recharged, an airbagfault code that was caused by battery voltage can be removed from memory. To check whether the Chevrolet airbag light has been reset after you have cleared it, switch off the ignition and then back on again. Return to the Airbag / SRS control unit and choose Clear / Erase Fault Codes from the drop-down menu
- Press enter.
It is possible that the problem has not been resolved, in which case the airbag light will illuminate again immediately or as soon as the fault is recognized again. These instructions are applicable to the Chevrolet Spark, Sonic, Bolt, Volt, Cruze, Malibu, Impala, Camaro, Corvette, City Express, Trax, Equinox, Traverse, Tahoe, Suburban, Colorado, Silverado, Sonic, Blazer, Astro, HHR, Uplander, Avalanche, and more models from the Chevrolet lineup.
Recall
Chevrolet has issued a number of airbag recalls during the course of the company’s history. Locate your vehicle identification number (VIN) in the lower-left corner of the windshield and contact any Chevrolet dealer to see whether any recalls are currently active. The dealer may be able to correct the problem for free if it is connected to a current recall for your Chevy airbag system if there is one open for your vehicle. As a result of the recall, the dealer will be required to diagnose the vehicle and confirm that the airbag light is illuminated.
Frequently Asked Questions
Is it possible to reset the airbag light on my Chevy by unplugging the battery?
- Disconnecting the battery for a few hours and then reconnecting it does not remove the airbag failure codes from Chevrolet automobiles. An automotive diagnostic scanner that can read and clear Chevrolet airbag codes will be required
Airbag fault codes on Chevrolet cars are not cleared by just unplugging the battery for a few hours and then reconnecting it. An automotive diagnostic scanner capable of reading and clearing Chevrolet airbag codes will be required;
- If you scan the vehicle with an OBD-II scanner and do not receive any codes, the most probable reason is that you are using a generic scanner that does not have the ability to access the Chevrolet airbag control module. Instead of utilizing a general scanner, utilize an airbag scanner specifically designed for Chevrolet.
What is the procedure for resetting the airbag light on a Chevrolet?
- Use an airbag scanner to read the trouble codes from the OBD-II port under the dashboard, which is located beneath the dashboard. When you read the codes, be sure you address all of the problem codes that were displayed. Reset the codes by scanning them with the scanner.
Why Is My Airbag Dash Light On? Three Possible Causes in Beaverton
While we hope you never find yourself in a scenario where your vehicle’s airbags are required to deploy, it is always a good idea to check that they are in working order. If a collision does occur, they have the potential to make a significant impact. That’s why, if your airbag dash light continues to illuminate, it’s critical that you take your vehicle to a Chevrolet or General Motors repair shop as soon as possible. The airbag light illuminates when there is a problem with the seatbelts or airbags in the vehicle.
Rather than driving it yourself to the dealership if the light remains lighted in your car, we recommend that you have it towed there.
It’s not always simple to determine the root reason, so it’s better to leave it to the professionals.
3. Computer Problems
This is one of several computer faults that might be causing your airbag light to remain illuminated, and we have only covered a few of them here.
When you bring your Chevrolet or General Motors car to a service shop, the experts will connect it to a code reader to diagnose the problem. They will be able to determine exactly what went wrong thanks to the computer.
2. Your Vehicle Has Been in an Accident
If your automobile has been in an accident, the airbag light will almost certainly be illuminated. This certainly applies in the case of major accidents in which the airbags have been deployed; if this has occurred and your car has been fixed, it is conceivable that the personnel who performed the repair neglected to reactivate the system. However, it can occur in minor collisions that occur at slower speeds as well. Even though the airbag did not deploy, it is possible that the collision sensors were engaged.
1. Your Seatbelts Aren’t Buckled Properly
Modern automobiles are equipped with sensors that detect when you have fastened your seatbelt properly. In the event that your seatbelt is not fully buckled—even if it seems to be—the sensor will activate the airbag warning light. A piece of trash (such as a lost penny) becoming lodged in the belt buckle, or an issue with the sensor wires themselves, might be the cause of this problem. Damage from corrosion or other objects may lead them to malfunction, resulting in their being unable to detect the connection.
Always remember to wear your seat belt.
4 Things To Know About the Airbag Light
Every year, the additional restraint systems installed in automobiles play a critical role in the saving of countless lives. Your safety will be jeopardized if the system does not operate as it is supposed to. Fortunately, if something goes wrong with the airbag system, a dashboard light will glow to alert the driver. Find out more about what this light represents in the section below.
4. The Seat Belts May Be To Blame
The Supplemental Restraint System (SRS) light refers to the whole Supplemental Restraint System. This suggests that the seat belts may possibly be a contributing factor to the light turning on. While ensuring sure everyone is belted in may remedy the problem, it is also possible that the problem is caused by a seat belt switch that is not recognizing a properly tightened belt. This might be caused by a foreign object, such as a penny, becoming stuck in the buckle, or it could be caused by a problem with the sensors themselves.
3. Airbag Control Module or Sensors May Be Faulty
The airbag control module is the computer that regulates the operation of the airbags, and it is often located under the driver’s seat. It receives information from a variety of impact sensors, which allows it to determine when the airbags should be deployed and activated. If the control module or any of the sensors fails to function properly, the airbag may not deploy when it is required to do so. Damage to the sensors or the control module can occur in vehicles that have had significant water damage, although it is not uncommon for them to fail on their own.
2. Your Vehicle May Have Been in a Previous Accident
If your vehicle was involved in a collision that was severe enough to trigger the impact sensors but not severe enough to cause the airbags to deploy, the light may come on as a result.
This is due to the fact that the control module may believe that the airbags have been deployed, which means that they will not deploy if you are involved in another collision. In most cases, a reset will take care of the problem.
1. Stop Driving
When this light illuminates, it is advisable not to continue driving regardless of the reason for its illumination. Airbags and seat belts are vital safety measures, and the presence of this light indicates that they may not function when they are most required. If you are involved in an accident, it is preferable not to put yourself or others in greater danger, therefore we recommend having your Chevrolet towed to a local service shop.
How do you reset the airbag light on a GMC Sierra?
Instructions on how to reset an airbag light
- Make sure that your car’s ignition is turned on and that the airbag light is illuminated before you start it. It will remain lighted for seven seconds before shutting off on its own accord. Repeat Steps 1 and 2 two more times after it has shut down. After it has shut down, immediately turn the switch off and wait three seconds
- Start the vehicle’s engine.
If your airbag light is illuminated, it may also signal that there is an issue with your seat belts. Aside from that, if your vehicle was involved in an accident that engaged the crash sensors in your vehicle but did not cause the airbag to deploy, your airbag or SRSlightmight also illuminate. You will need to get your airbags reset in this situation. In addition to the instructions above, how do you reset the airbag light on a Chevrolet Silverado? Instructions on how to reset an airbag light
- Step 1: Connect the various components. In order to reset the airbag light, you must first make sure that all of the components in the dash are connected in and working properly. Step 2 – Turn the ignition to the ‘On’ position
- Step 3 – Time the Airbag Light
- Step 4 – Turn the ignition to the ‘On’ position again after 3 seconds
As a result, one may wonder if it is possible to reset the airbag light without using a tool. Before attempting to reset the light, you should always verify the airbag codes using a scanner and correct the problem. It is possible to reset it without using a scanner, but you should avoid doing so if the problem persists because doing so may cause the airbags to deploy prematurely. What is the procedure for turning off the airbag on a GMC Sierra? If you want to turn off the right front passenger airbag, you must first enter the ignition key into the switch, push it in, and then move the switch to the off position.
How do i reset airbag light on chevy silverado?
In order to turn off the airbag light on a Chevrolet Silverado, first turn off the ignition. An electronic scan instrument must be used to diagnose the truck, and you must pay for this service. Numerous factors might be responsible for the light being turned on in the first place. The scan tool will be connected to the OBD-II port and will provide you with information about the problems. The vehicle is equipped with a number of sensors, including those on the front and rear bumpers, seatbelts, and doors.
- Replace a damaged sensor might cost anywhere between $170 and $190, including labor charges, depending on the situation.
- Lionel M.
- The 9th of April, 2020 When you want to reset the airbag in your Silverado, just put the key in the ignition and turn the switch to the on position.
- It will remain lighted for seven seconds before automatically turning off.
My airbag light is flashing on my Chevrolet Silverado 2020. How can I reset it, and what does it indicate? The air bag light on my 2003 Chevrolet vehicle does not illuminate. DannyC The deadline for submissions is December 29, 2021. The airbag light continues to illuminate.
GMC Sierra: Airbag Light Stays On Diagnosis
Every time you start your GMC Sierra, the computer system performs a self-diagnostic check on all of the vehicle’s essential components. If any of these tests fail, you will notice a diagnostic warning light illuminated on the instrument panel for the system that failed. When the airbag system fails this check, the airbag light will illuminate. It might be anything along the lines of SRS, an image of a person who has their airbag deployed, or the term airbag, depending on the model year and the nation in which you happen to be.
A warning light on your Sierra’s airbag system is there to inform you when there is a problem with the system.
When it remains on, it signals that there is a problem.
GMC Sierra Airbag Light on Causes
Your Sierra’s airbag light is a component of the vehicle’s bigger supplementary restraint system. It works in conjunction with the rest of the system to keep you safe in the case of an accident. In the event that all components of this system are not functioning properly, the airbag light may illuminate. The airbag light will remain illuminated after an accident until the system has been fully repaired or replaced. It will not function until it has been fixed. Here are some of the most common reasons why the airbag light on your Sierra may illuminate.
1.Seat Belts
In the event that your Sierra is involved in an accident, safety belts are still the most crucial safety element. Modern automobiles are equipped with sensors that communicate with the computer system to determine whether or not they are strapped and whether or not they are locked up. If you have a seat belt that is caught in the lock position, it is possible that this is the cause of your airbag light turning on. Check to see if you can get it going again by tugging on it.
2.Seat Sensors
The airbag system is alerted when the seat sensors detect that the seat is occupied. Some older model automobiles feature a manual button that may be used to switch on or off the passenger airbag. Look behind the seats to see if you can identify any parts of the wiring harness that have been loose or damaged as a result of the accident. This is one of the most typical reasons why the airbag light illuminates.
3.Airbag Itself
If the Sierra’s airbag system is unable to get a response from one of the airbags during the diagnostic cycle, the airbag light will illuminate until the problem has been resolved and the system has been reset, which might take several minutes.
4.Airbag ECU/Sensors
It’s possible that the control unit for the airbag system has failed. It is possible to get it replaced or to request a new one in this situation. This is common when you are involved in a fender accident that does not result in the deployment of the airbag. It’s possible that one or more of the collision sensors were activated, but not enough to cause the airbag to deploy.
It is also possible for the airbag sensors to fail and illuminate the airbag light if there is water damage. This is one of the reasons why it is not a good idea to purchase an automobile that has flood damage, even if it appears to be in otherwise good condition.
5.Not Reset After Deployment
If your vehicle’s airbag has been deactivated and replaced, the airbag system must be re-activated. After the airbag system has been reset by a shop or you have sent the module to someone who can do it for you, it will not work until the airbag system has been reset.
Is it Safe to Drive Your Sierra with the Airbag Light On?
Driving with the airbag light illuminated is not as safe as it should be. Since its inception, the airbag system has saved a vast number of lives. You are depending only on your Sierra’s safety belts to keep you safe if you choose to drive with the airbag light illuminated. This is a less-than-safe driving practice. Almost all of the safety technology that saves you from crashing is still in place (assuming your vehicle is equipped with it), including traction control, anti-lock brakes, and blind spot recognition.
Conclusion:GMC Sierra Airbag Light On
The airbag system in your GMC Sierra is quite intricate. There are a variety of various reasons why the airbag light may have illuminated on your vehicle. The majority of them should be left in the hands of a professional. It is not enough that the car can be driven in order to dismiss the problem as unimportant. If you have anything to contribute, please leave a remark in the section below. Thanks for reading. Wishing you the best of luck!
Intermittent Airbag Light Affects Later-Year GM Models
Two collision repairers were able to save their lunch plans thanks to OE-specific information. With a Bachelor of Science in communication and more than ten years of experience in the collision business, Karl Kirschenman serves as president for K2 Consulting Group. He also holds a Master of Science in communication. He has previously held positions as the collision program manager for ALLDATA and the director of technology for I-CAR, among other positions. On a Friday afternoon, I dropped by my friend Mike’s store to explore the possibility of going to a deli for lunch.
- I’m hungry, and I’m thinking that if he’s driving an exotic automobile, it better be something special because he’s compromising our chance to obtain a table at the deli.
- The Light Has Been Turned On The vehicle in question is a 2009 Chevrolet Malibu.
- I ask Mike about the damage to the front fender, and he says, ‘There was no one in the car.’ An intermittent malfunction is causing the airbag light to illuminate on the dash of the vehicle.
- I forgot to say that it was Friday.
- Nothing makes sense when it comes to the codes.
- Michael received a call from a client who stated that the intermittent airbag light was not a problem prior to the accident.
- We begin by going over the diagnostic trouble codes (DTCs) one by one once more to see what they mean.
Nothing happened on the second try.
After only ten minutes of investigation, we have discovered the main source of the problem.
It has been discovered that there has been a problem with various General Motors makes and models dating back to 2005 and extending into some 2012 vehicles, among others.
Whenever a General Motors consumer complains of an intermittent airbag light on his or her dashboard, look for the following DTCs to be set: B0012, B0013, B0015, B0016, B0019, B0020, B0022, B0023, B0026, B0033, B0040, B0042, or B0044.
It was B0022 who alerted Mike and myself to the presence of a problem.
Examining the connection position assurance (CPA) retainer is necessary to resolve the problem.
It is possible that the offending retainer is loose, missing, or broken at an airbag/SIR module electrical connector or at an electrical connector on a deployment loop wire harness wiring harness.
Otherwise, you could find yourself eating an airbag at lunch instead of a delicious deli sandwich.
In his report, the expert says that he rapidly separated the damaged connector and determined that corrosion was the source of the problem by consulting the original equipment manufacturer’s process and components information.
I decide to drop by again the following Friday to drag Mike out to lunch and see what other riddles we can solve with the help of the magic of original equipment manufacturer repair information.
Refer to the whole article in ALLDATA Collision S3500 before trying any of the repairs outlined.
Karl Kirschenman, ALLDATA collision product manager, has a master of science in communication from the University of Illinois.
ALLDATA LLC is a trademark of ALLDATA LLC.
The ALLDATA Collision S3500 is the source of all technical information, photos, and specs.
ALLDATA is a registered trademark of ALLDATA LLC.
Buick, Cadillac, Chevrolet, GMC, Pontiac, Saturn, Hummer, Daewoo, and Opel are trademarks of General Motors. SPX Corporation owns the trademark Kent Moore Tools, which is a registered trademark of the company. All other trademarks and service marks are the property of their respective owners.
Airbag light on GM vehicles
General Motors has issued a service bulletin to address an airbag light on condition in conjunction with the following trouble codes: B0012, B0013, B0015, B0016, B0019, B0020, B0022, B0023, B0026, B0033, B0040, B0042 or B0044 on the vehicles listed below: Chevrolet, Buick, GMC, GMC Sierra, GMC Sierra Denali, GMC Terrain. Buick Rainier (2005-2007 model years) Buick Allure (available in Canada only), LaCrosse, and Lucerne (2006-2009) Buick Enclave models from 2008 to 2014. Cadillac DTS from 2006 until 2011.
- Cadillac XLR 2008-2009 Cadillac STS 2008-2011 Cadillac XLR Cadillac CTS and SRX models from 2008 to 2014.
- Chevrolet Cobalt (2005-2010 model years) Chevrolet Monte Carlo (2006-2007 model years) Chevrolet HHR from 2006 to 2011.
- (includes Malibu Classic) Chevrolet Equinox (model years 2007-2009) Chevrolet Avalanche, Silverado, Suburban, and Tahoe models from 2007 to 2014.
- The Acadia, Sierra, Yukon, Yukon Denali, Yukon Denali XL, and Yukon Denali XL are all 2007-2014 GMC models.
- Pontiac Pursuit from 2005 to 2006.
- Pontiac Torrent 2007-2009 Pontiac G5 2007-2010 Pontiac G5 Pontiac G8 (2008-2009 model year) Saturn AURA, OUTLOOK, and SKY (2007-2009) Saturn VUE for the years 2008-2009 HUMMER H2 (2008-2009 model year) Daewoo G2X (2007-2008 model year) Opel GT from 2007 to 2009.
Cause of airbag light on condition
For its airbags, General Motors use a proprietary connection. The connector features a specific locking clip, known as a connector position assurance (CPA) clip, that is used to keep the two sections of the connector locked together. The electrical connecting sections as well as the CPA are seated separately from one another. When properly placed, the CPA isolates the shorting bars within the electrical connector, making it an extremely important component of the airbag system. If the CPA clip is not present or has been inserted improperly, the system will generate an issue code and illuminate the airbag light to alert the user.
Fix the airbag light on condition
Determine which connector is causing the problem by looking at the trouble codes displayed on the screen. After that, turn off the airbag system before continuing. Check the connection and CPA to ensure that the two parts of the connector are correctly connected and that the clip is securely fastened. If the CPA is misplaced or missing, it should be replaced. Removing the CPA and unplugging the electrical hookup are both recommended. Ensure that the terminals are free of corrosion and contaminants.
If you discover corrosion or damage to the terminals, you MUST replace them with specific terminals purchased from the dealer.
Airbag terminal repair kit If you utilize standard terminals, you will experience difficulties.
Kit for repairing SIR terminals (J-38125).
When you have finished repairing the terminals, apply dielectric grease GMP/N 12345579 to the connection pins and terminals before reassembling the system. Reassemble the connector, making sure to hear and feel an audible click as you do so. The CPA clip should then be reinstalled.
Finish airbag repair
The airbag codes should be cleared, and the airbag light should be checked on the next IGN cycle. Rick Muscoplat has a new year’s resolution. Rick Muscoplat posted a blog entry on
GMC Sierra 1500 Air Bag Light On Problems
During the next IGN cycle, clear the airbag codes and look for the airbag light. Rick Muscoplat has a new year’s resolution: Rick Muscoplat wrote a post on
1Air Bag Light On problem of the 2012 GMC Sierra 1500
On the next IGN cycle, clear the airbag codes and look for an airbag light. Rick Muscoplat’s newest album, 2018 Rick Muscoplat posted a message on
2Air Bag Light On problem of the 2012 GMC Sierra 1500
Failure Date:11/23/2020 Inability to turn off the service airbag light When you’re driving, it’s best to keep your hands on the wheel.
3Air Bag Light On problem of the 2014 GMC Sierra 1500
Failure Date: Friday, June 6, 2020 When I drove my vehicle to the local GMC shop for the recall fix, the service advisor asked if I would want to have the truck diagnosed for a fee. I replied yes since I had a check engine light and a service air bag light illuminated on my dashboard. Which they both arrived on within a week of my purchasing it. As a result, the service adviser informed me that the belt tensioner on the driver’s side had failed, and that the wiring under the driver’s seat has become tangled.
However, I inquired as to whether the seat belt and malfunctioning issue was covered by a safety warranty.
It has come to my attention that these goods are subject to a recall, with the recall number 15522.
Thanks.
4Air Bag Light On problem of the 2009 GMC Sierra 1500
Expiration date: Friday, June 6, 2020 The GMC dealership where I took my vehicle for the recall repair asked if I would want to have the truck diagnosed for an additional fee. A check engine light was illuminated, as was a service air bag light, so I responded affirmatively. The fact that they both arrived within a week of me purchasing it is remarkable! As a result, the service adviser informed me that the belt tensioner on the driver’s side has failed, and that the wire under the driver’s seat has become entangled.
- However, I inquired as to whether the seat belt and malfunctioning issue was covered by a safety guarantee.
- Afterwards, he told me no, and that it would cost 5400 dollars to fix your vehicle.
- For this reason, I’d like to find out whether or not I’m the services consultant.
- All of the issues with the 2014 GMC Sierra 1500 may be found right here!
5Air Bag Light On problem of the 2014 GMC Sierra 1500
Failure date: Friday, June 6, 2020 When I drove my vehicle to the local GMC shop for the recall fix, the service advisor asked if I would want to have the truck diagnosed for an additional fee. I replied yes because my check engine light and service air bag light were both illuminated. They both arrived within a week of my purchase. So the service adviser informed me that the belt tensioner on the driver’s side is not working properly, and that the wiring under the driver’s seat is faulty. They also told me that there was something else wrong with my truck, which I later discovered to be untrue.
And he replied no, and that it would cost 5400 dollars to fix your truck. I’ve discovered that these things have been recalled, and the recall number is 15522. So I’d like to know if I’m the services advisor or if I’m not. Thanks. See all of the issues with the 2014 GMC Sierra 1500.
6Air Bag Light On problem of the 2012 GMC Sierra 1500
Failure occurred on October 27, 2019. An independent mechanic phoned on behalf of the owner of a 2012 GMC Sierra 1500, who had just purchased the vehicle. As the vehicle was traveling at 30 mph, the front and rear driver side curtain air bags deployed on their own, and the air bag warning signal came on. There were no injuries on either end. A collision repair company was called in and the air bags were fixed on the car. The car was not diagnosed or fixed as a result of the incident. The dealer and the manufacturer were not informed of the situation.
7Air Bag Light On problem of the 2005 GMC Sierra 1500
Failure occurred on: 05/12/2019 The contact has a 2005 GMC Sierra 1500 pickup truck. An air bag warning sign had been activated, according to the contact. The car was towed to a local independent mechanic, who reported the incident to the National Highway Traffic Safety Administration. The car was not diagnosed or fixed as a result of the incident. The dealer and the manufacturer were not contacted for this article. With 156,000 miles on the odometer, there occurred a failure. See a list of all the problems with the 2005 GMC Sierra 1500.
8Air Bag Light On problem of the 2007 GMC Sierra 1500
05/12/2019 is the date of the failure. A 2005 GMC Sierra 1500 is now in the possession of the customer. An air bag warning sign had been activated, according to the source. It was determined that the car needed to be towed to an independent mechanic, who forwarded the information to the National Highway Traffic Safety Administration. Neither the vehicle’s diagnosis nor its repair were completed. No contact was made with the dealer or the manufacturer. Approximately 156,000 miles were covered before the collapse.
10Air Bag Light On problem of the 2016 GMC Sierra 1500
Failure occurred on December 17, 2018. The client is the owner of a 2016 GMC Sierra 1500 pickup truck. It became visible when the car was started since the air bag warning sign was activated. The driver and passenger side curtain airbags were deployed while traveling at about 45 mph on the highway. The contact brought the car to a halt in the middle of the highway until the police were able to respond. After the car was hauled away, the contact returned home. In this case, the car was towed to finnegan Chevrolet (26529 Southwest Fwy, Rosenberg, Texas 77471), where it was determined that the headliner and sensors needed to be replaced.
The failure was not communicated to the manufacturer in advance.
See a list of all the issues with the 2016 GMC Sierra 1500.
12Air Bag Light On problem of the 2011 GMC Sierra 1500
Failure occurred on June 5, 2018. The airbag light was on and flashing.
13Air Bag Light On problem of the 2007 GMC Sierra 1500
I have not been provided alternative mode of transportation by my truck dealer, despite my failure date being 06/01/2018. ‘takata recall’ components are still not available to fix my truck. I have two children that travel in my truck on a regular basis because it is my sole mode of transportation to and from work, as well as transporting them to and from school, sports events, the grocery store, and any other location where I need a vehicle to go to. I don’t feel secure driving my truck because it has a major safety concern that has been recalled for more than a year at this point.
Because parts are still not available at this time, General Motors should be ensuring that I have a safe car to drive until they can fix it. The airbag light has now flashed on and off a few times in the course of the day.
14Air Bag Light On problem of the 2007 GMC Sierra 1500
I have not been provided alternative mode of transportation by my truck dealer, despite my failure date of 06/01/2018. ‘takata recall’ components are still not available to fix my truck. As a result, I have two children who travel in my truck on a regular basis because it serves as my only mode of transportation to work, as well as to school, sports events, the grocery, and any other locations where I need a vehicle. Despite the fact that there has been a major safety concern with my truck for more than a year, I do not feel confident driving it.
As a result of parts being unavailable at this time, General Motors should be ensuring that I have a safe car to drive until they can fix it.
15Air Bag Light On problem of the 2009 GMC Sierra 1500
Failure occurred on 04/02/2018. An airbag issue is indicated by an indicator light on the dashboard. The dash also indicates that the airbag has been maintained.
17Air Bag Light On problem of the 2008 GMC Sierra 1500
Failure occurred on February 6, 2018. The client is the owner of a 2008 GMC Sierra 1500 pickup truck. Apparently, the air bag sensors in the car were rusted, according to the contact. Both before and after the failure, the air bag indicator was flashed on the dashboard. The failure was not communicated to either the dealer or the manufacturer. The automobile was not fixed in this instance. The vehicle identification number (VIN) was not given. The failure mileage was around 120,000 miles. See a list of all the problems with the 2008 GMC Sierra 1500.
18Air Bag Light On problem of the 2009 GMC Sierra 1500
Failure occurred on January 15, 2018. (kh – dealer info inadequate) tl takata recollections The client is the owner of a 2009 GMC Sierra 1500 pickup truck. A notification of NHTSA campaign number 16v381000 (air bags) was received by the contact; however, the parts needed to complete the repair were not readily accessible. In addition, the service air bag warning signal came on and remained on. The manufacturer, according to the contact, surpassed a reasonable period of time for the recall repair to be completed.
Buick GMC was contacted and confirmed that the parts needed for the recall fix were not available at the time.
The issue was brought to the attention of the manufacturer, who was unable to provide an estimate for when replacement components would be available.
The VIN tool verifies that the components are not available.
19Air Bag Light On problem of the 2013 GMC Sierra 1500
Failure occurred on December 27, 2017. The contact has a 2013 GMC Sierra 1500 pickup truck. According to the contact, the air bag indication has been flashing for at least two years at this point. Despite the fact that the car was transported to vince webb Cadillac of pensacola (5651 pensacola Blvd, pensacola, FL 32505, (850) 912-9372), no diagnosis or repair were performed on the vehicle.
The manufacturer was not informed of the situation. One hundred and twenty thousand miles were covered in failures. See a list of all the problems with the 2013 GMC Sierra 1500.
20Air Bag Light On problem of the 2010 GMC Sierra 1500
Failure occurred on November 25, 2017. The client is the owner of a 2010 GMC Sierra 1500 pickup truck. According to the contact, the service air bag indicator lighted and stayed on during the whole trip. There was no recall when the contact phoned randy curnow Chevrolet Buick GMC (816-632-2162, 509 Northland Dr, Cameron, MO 64429), and the representative informed him that there was no such recall. The cause of the malfunction was not determined. The failure was not communicated to the manufacturer in advance.
21Air Bag Light On problem of the 2014 GMC Sierra 1500
25th November, 2017 was the day of the failure. An 2010 GMC Sierra 1500 is now in the possession of the contact. When the service air bag indicator illuminated, the contact said that it stayed illuminated during the whole trip. When the contact phoned randy curnow Chevrolet Buick GMC (816-632-2162, 509 northland road, cameron, mo 64429), he was told that there was no recall on the vehicles. It was not determined what caused the failure. The failure was not communicated to the manufacturer until after it occurred.
22Air Bag Light On problem of the 2009 GMC Sierra 1500
Failure occurred on January 11, 2017. Tl takata recollections The client is the owner of a 2009 GMC Sierra 1500 pickup truck. The contact stated that the air bag warning indicator had been illuminated for several months at the time of contact. NHTSA contacted the dealer, who responded by stating that the vehicle was not included in campaign number: 16v381000. The dealer’s address is 613 n paseo DE onate, espa ola, NM 87532, and their phone number is 1-(866) 512-6302. (air bags). The vehicle identification number (VIN) was not accessible.
The contact was looking forward to finding a solution to repair his car.
There had been no failure on the part of the contact.
23Air Bag Light On problem of the 2009 GMC Sierra 1500
Failure occurred on Tuesday, February 10th, 2017. The vehicle will display a warning signal when the stabiltrack is turned off at random. Then it will cycle the door locks up and down, switch on the air bag light and the ABS light, and occasionally reduce the vehicle’s speed to 20 miles per hour. It will also cause the gauges in the car to malfunction. Despite many trips to the store, the problem has not been resolved. A simple Google search for stabiltrack 2009 Chevrolet/GMC will yield a plethora of results.
This occurs when the vehicle is in motion, which increases the level of anxiety associated with it.
The vehicle presently has 96k miles on it.
24Air Bag Light On problem of the 2005 GMC Sierra 1500
Failure occurred on August 19, 2017. The client is the owner of a 2005 GMC Sierra 1500 pickup truck. The contact indicated that the air bag warning sign had stayed illuminated during the conversation.
The car was not diagnosed or fixed as a result of the incident. There was no attempt to contact a local dealer. The failure was not communicated to the manufacturer in advance. The failure mileage was not known at the time.
25Air Bag Light On problem of the 2011 GMC Sierra 1500
Failure occurred on July 15, 2017. The service is available. The airbag light flashes on and off, and the outside air temperature reads 55 degrees while it’s 92 degrees outdoors when it’s moving or motionless.
26Air Bag Light On problem of the 2010 GMC Sierra 1500
Failure occurred on June 15, 2017. The client is the owner of a 2010 GMC Sierra 1500 pickup truck. The air bag indicator lighted immediately after the car was started. In order to identify the problem, the car was transported to yates Buick GMC (13845 West Test Drive in Goodyear, Arizona 85338), where it was discovered that a crimped wire going to the air bag had produced a short, and the wire needed to be replaced. The dealer also noted that if the indicator flashed again after the repair, the air bag would also need to be replaced, according to the dealer.
The issue was brought to the attention of the manufacturer, who responded by stating that they would replace the air bag at a discounted cost.
27Air Bag Light On problem of the 2007 GMC Sierra 1500
Failure occurred on May 31, 2017. In summary, the customer has a 2007 GMC Sierra. In response to the contact’s complaint, the air bag light began blinking. The contact had received information of NHTSA campaign number: 16v383000 (air bags), however the parts needed to complete the repair were not available at the time of writing. The manufacturer, according to the contact, surpassed a reasonable period of time for the recall repair to be completed. A local dealer, everett Buick GMC of Bentonville, situated at 2517 SE Best Lane, Bentonville AR 72712 responded to the contact’s call, and the contact was advised that the recall remedy components were no longer available.
A snag had occurred with the contact’s business.
(The VIN tool verifies that the components are not available.) Ap.
28Air Bag Light On problem of the 2014 GMC Sierra 1500
Failure Date:05/01/2017 The airbag needs to be serviced. The caution indicator continues to appear. Every 30 seconds or so, about. I have to continuously pressing the ‘dismiss’ button.
29Air Bag Light On problem of the 2007 GMC Sierra 1500
Failure occurred on March 27, 2017. Takata is being recalled. The client is the owner of a 2007 GMC Sierra 1500 pickup truck. The contact had received information of NHTSA campaign number: 16v383000 (air bags), but the part for the recall repair was not available at the time of the call. The manufacturer, according to the contact, surpassed a reasonable period of time for the recall repair to be completed. The caller said that the air bag warning signal had been flashed on the vehicle’s dashboard.
The problem was not brought to the attention of the manufacturer.
30Air Bag Light On problem of the 2009 GMC Sierra 1500
Failure occurred on January 17, 2017. The client is the owner of a 2009 GMC Sierra 1500 pickup truck. The contact got news of NHTSA campaign number: 16v381000 (air bags); but, the part for the recall repair was not available at the time of the contact’s request. The manufacturer, according to the contact, surpassed a reasonable period of time for the recall repair to be completed.
An air bag warning sign had been activated, according to the contact. The estimated mileage of failure was 122,000 miles. The manufacturer was not informed of the situation. The VIN tool verifies that the components are not available.
31Air Bag Light On problem of the 2007 GMC Sierra 1500
Failure occurred on March 1, 2017. The client is the owner of a 2007 GMC Sierra 1500 pickup truck. The contact got news of NHTSA campaign number: 16v381000 (air bags); but, the part for the recall repair was not available at the time of the contact’s request. The manufacturer, according to the contact, surpassed a reasonable period of time for the recall repair to be completed. The contact reported that the warning signs for the driver’s and passenger’s side air bags were both illuminated at the time.
The problem was brought to the attention of the manufacturer.
33Air Bag Light On problem of the 2008 GMC Sierra 1500
Failure occurred on January 1, 2017. The air bag light is illuminated. I inquired with the vendor about it.
34Air Bag Light On problem of the 2014 GMC Sierra 1500
Failure occurred on November 29, 2016. The client is the owner of a 2014 GMC Sierra 1500 pickup truck. As I was travelling at roughly 70 mph, the car slowed and the abs and brake lights came on, as well as the check engine light and other warning lights. The brake pedal was pushed all the way to the floorboard. Afterwards, the vehicle was coasted to the side of the road and driven back to the house. Despite taking the car to the dealership, no one was able to determine what had caused the malfunction.
The problem was brought to the attention of the manufacturer, who did not reply.
In the case of failure, the distance was around 29,000 miles.
35Air Bag Light On problem of the 2009 GMC Sierra 1500
Failure occurred on January 10, 2016. The client is the owner of a 2009 GMC Sierra 1500 pickup truck. In response to the contact’s question, the air bag indicator lighted for him. A notification of NHTSA campaign number 16v381000 (air bags) was received by the contact; however, the parts needed to complete the repair were not readily accessible. The manufacturer, according to the contact, surpassed a reasonable period of time for the recall repair to be completed. When the contact phoned a local dealer (240 Old Gibson Road, Henderson, NV 89014), he was told that the components were not available at that location.
The failure mileage was not known at the time.
GM Issues Service Bulletin For Intermittent Airbag Light.
A technical service bulletin (TSB) has been published by General Motors to resolve a problem with the airbag light on some 2021 SUVs. In some General Motors full-size SUVs from the 2021 model year, the electrical connection to the seat-mounted inboard airbag system can be disrupted by driver movement. During this time, the driver information center will show a ‘Service Restraints System’ notice to the driver until resistance to the connection eventually stops the airbag from being deployed. The TSB affects the following General Motors full-size SUVs:
- 2021 Chevrolet Tahoe
- 2021 Chevrolet Suburban
- 2021 Cadillac Escalade
- 2021 Cadillac Escalade ESV
- 2021 GMC Yukon
- 2021 GMC Yukon XL
On some 2021 General Motors full-size SUVs, a technical service bulletin (TSB) has been issued to fix an issue with the airbag light that has been reported by customers. According to the Technical Service Bulletin (TSB) that GM distributed to dealerships, driver movement might cause the electrical connection to the seat-mounted inboard airbag system in some GM full-size SUVs from the 2021 model year to become unstable. During this time, the driver information center will show a ‘Service Restraints System’ notice to the driver until resistance to the connection eventually stops the airbag from being deployed.
A condition that has the potential to cause an airbag malfunction such as this would normally be subject to a recall by the National Highway Traffic Safety Administration, but because the seat airbag is not required by law, the matter is being addressed by the Transportation Safety Board.
These repairs should take no more than an hour to complete and will be provided at no cost to the vehicle’s proprietor. The TSB affects the following General Motors full-size SUVs:
- 2021 Chevrolet Tahoe
- 2021 Chevrolet Suburban
- 2021 Cadillac Escalade
- 2021 Cadillac Escalade ESV
- 2021 GMC Yukon
- 2021 GMC Yukon XL
This TSB program began in December 2020 and will last through December 31st, 2022. It is funded by the Department of Defense. In a recent post, we discussed how consumers reported encountering difficulties with the seat-mounted supplemental airbag control module under the driver’s seat. This bulletin will address the same issue in greater detail. A number of other TSBs have been issued for various 2021 model year full-size SUVs, including one to address a small issue with the LED lights on the Tahoe and Suburban, as well as one to address a problem with the trailering labels on the Yukon and Yukon XL models.