Torque Specifications
| Lug Nut/Bolt Torque | Lug Nut/Bolt Type |
|---|---|
| 130 Ft-Lbs (176 N·m) | Cone |
| 140 Ft-Lbs (190 N·m) | Flanged |
What is the lug nut torque on a 2017 Jeep Wrangler?
The torque is supposed to be 105 ft lbs.
How do I know what to torque my lug nuts to?
Use torque sticks with an air gun or a torque wrench to get the correct torque. If your studs or lug nuts are sized between 12 X 1.25mm to 1.5mm or are 7/16-inch, torque the nuts to 70 to 80 foot-lbs; 14 X 1.25mm to 1.5mm, to 85 or 90; 1/2=inch 75 to 85; and 9/16-inch 135 to 145.
What torque should wheel nuts be NM?
The optimum torque value for your car or mounted rims can be found in the vehicle manual. It depends on the car model, rim size, design (aluminium or steel rims) and number of bolts. It is normally between 110 N⋅m and 120 N⋅m.
What size are Jeep Wrangler lug nuts?
The Jeep JL is a fourth generation “Wrangler” that’s equipped with A5 X5 inches lug nut pattern and uses a 19mm socket to remove its wheel fasteners. To replace the lug nuts use a torque of 176 Nm and a thread size of M14 X1.
What is the torque spec?
Recommended torque specifications are unique for each type of vehicle. By definition, torque refers to the amount of rotational force at the point of application. When attaching a wheel to a vehicle, torque specifications are the amount of force recommended on the hardware to ensure proper installation.
What happens if you over torque lug nuts?
Excessively tightened lug nuts can strip the threads, distort brake rotors, damage the wheel, and possibly shear off the lug stud.
What does NM mean in torque?
The formula for torque, the law of the lever is: torque = force (N) x lever arm (m). The units for torque are newton-meters (Nm) or pound-feet (lb-ft). Newton (or pound) stands for the force that is acting, while meters (or feet) stand for the length of the lever arm.
Can you over torque lug nuts by hand?
Over tightening means that you have reached the end of the thread so the nut is flat against the wheel or whatever and you continue to tighten and start stripping the thread or twisting the bolt. So no, unless you are a cyborg with bionic hands, you cannot over tighten a lug nut by hand.
Jeep Wheel Bolt Patterns & Typical Lug Bolt Torque Specifications
Staff Report from Torque It is unavoidable in some cases. You enjoy the wheels on your Jeep, but you’ve recently come across a pair on another Wrangler that you think is even better. Alternatively, you may have suffered from a case of ‘off-road’ rock rash the last time you went on an adventure and wish to remedy the situation. Perhaps it is only a matter of time. This occurs from time to time, but when it does and you are ready to replace your wheels, it can be difficult to determine what bolt pattern is appropriate for your vehicle.
The reason for this is that while most Jeeps have five lugs, the spacing between the lugs varies depending on the specific model.
The 5×4.5 pattern is used on earlier TJ Wrangler vehicles (from 1997 to 2006) and YJ versions (1987 to 1995).
| Vehicle/Year Ranges | OEM Wheel Size | Lug Pattern | Stud Size | Hub Center Bore |
| 2020-22 Jeep Gladiator JT | 17″ – 18″ | 5 on 5 | 14mm x 1.50 | 71.5 |
| 18 – 22 Jeep Wrangler JL | 17″ – 18″ | 5 on 5 | 14mm x 1.50 | 71.5 |
| 07 – 18 Jeep Wrangler JK | 17″ – 18″ | 5 on 5 | 1/2 x 20 | 71.5 |
| 97 – 06 Jeep Wrangler TJ | 15″ – 16″ | 5 on 4.5 | 1/2 x 20 | 71.5 |
| 87 – 95 Jeep Wrangler YJ | 15″ – 16″ | 5 on 4.5 | 1/2 x 20 | 71.5 |
| 41 – 86 Jeep MBCJ Series | 15″ | 5 on 5.5 | 1/2 x 20 | 108 |
| 84 – 01 Jeep Cherokee XJCommanche MJ | 15″ | 5 on 4.5 | 1/2 x 20 | 71.5 |
| 93 – 98 Jeep Grand Cherokee ZJ | 15″ | 5 on 4.5 | 1/2 x 20 | 71.5 |
| 99 – 04 Jeep Grand Cherokee WJ | 16″ – 20″ | 5 on 5 | 1/2 x 20 | 71.5 |
| 05 – 10 Jeep Grand Cherokee WK | 16″ – 20″ | 5 on 5 | 1/2 x 20 | 71.5 |
| 11 – 19 Jeep Grand Cherokee WK2 | 16″ – 20″ | 5 on 5 | 14mm x 150 | 71.5 |
| 14 – 19 Jeep Cherokee KL | 17″ – 18″ | 5 x 110(metric) | 12mm x 1.25 | 65.1 |
| 06 – 10 Jeep Commander XK | 17″ – 18″ | 5 on 5 | 1/2 x 20 | 71.5 |
| 02 – 12 Jeep Liberty KJ/KK | 16″ – 18″ | 5 x 4.5 | 1/2 x 20 | 71.5 |
| 07 – 16 Jeep Compass, Patriot | 17″ – 18″ | 5 on 4.5 | 12 x 1.5 | 67.1 |
| 62 – 73 Jeep J SeriesFull Size Wagoneer | 15″ | 5 x 5.5 | 1/2 x 20 | 108 |
| 74 – 91 Jeep J SeriesFull Size Wagoneer | 15″ | 6 on 5.5 | 7/16 | 108 |
How to Measure Your Bolt Pattern
Some of you may be unclear of what sort of Jeep you have or what year it is now that you understand bolt patterns. Rather than embarking on a time-consuming journey to obtain such information, just measure the lug pattern size. To begin, count the number of lug bolt holes. A Jeep often has five lugs, which makes measuring a little more harder, but not impossible – all you have to do is measure the bolt pattern circle (the yellow circle on the diagram below). Choosing any bolt hole to begin with and aligning your ruler at the furthest edge of the hole will allow you to measure to the center of the next adjacent hole, which will allow you to complete the task (as indicated by the blue line in the diagram).
This specific wheel had five holes, and when we tested the bolt pattern circle diameter, we found that it was 4.5 inches in diameter.” As a result, we would state that the bolt pattern is 5 on 4.5 or 5×4.5 in nature.
How to Properly Torque Lug Nuts
Making certain that the lug nuts are tight once the wheels are on isn’t just a matter of good intentions. It is something that must be done in order to maintain optimum safety when operating your Jeep vehicle. So, once those wheels are mounted on your Jeep, start by tightening the first lug with a sturdy lug wrench, such as the Gorilla Power Lug Wrench, to the required tension (the exact torque for your vehicle can be found in your owners manual). Then, continue on to the lug nut that is immediately adjacent to the one you just tightened.
Follow the method described in the image below, working your way back and forth across the wheel until all of the lug nuts are correctly torqued (see diagram below).
One thing to keep in mind is that you should not overtighten those lug nuts.
Once you’ve determined which bolt pattern is best for your Jeep, be sure to visit our Wheel and Wheel Accessory page to see all of the fantastic alternatives that are now available.
| Lug Size | Ft/Lbs Torque |
| 7/16″ | 55-65 |
| 1/2″ | 75-85 |
| 9/16″ | 95-115 |
| 5/8″ | 135-145 |
| 12mm | 72-80 |
| 14mm | 85-95 |
IMPORTANT NOTICE: After installing your new wheels lugs, please check the lug torque after 20-30 miles to ensure that the lugs are properly torqued. After an extra 100 miles, check the torque once again. Refer to the Owner’s Manual for factory instructions on how much wheel torque is required. If one of your New Year’s resolutions is to spruce up the interior of your Jeep, here are the goods you’ll need to make that goal a reality. In this time of year, it is not only prudent to prepare and store a winter emergency kit in your vehicle, but it is also recommended for everyone.
- However, even if we believe that driving a Jeep is not about getting the best mileage possible, it doesn’t harm to adopt certain fuel-saving strategies.
- Jeep’s Gladiator pickup truck is one of the most popular models in the company’s lineup.
- Changes for the 2022 model year include a new basic infotainment system as well as an upgraded air filtering system.
- The patent application was initially submitted in 2017, however the business has no intentions (at least for the time being) to bring the doors into production.
Jeep Wrangler JK Exterior Torque Specs
Exterior components for the Jeep Wrangler JK may be found here. Exterior of the store
Wheel Torque Specs
Luggage nut replacement is more frequent than any other type of maintenance on your Wrangler, except for oil changes and tire rotations. Every time you work with them, it is critical that you torque them appropriately to ensure that they function properly. When tightening lug nuts, make a star pattern with your movements.
| Description | Specification | |
|---|---|---|
| Lug Nut 1/2 X 20 with 60° Cone | 85-125 ft-lbs | |
| Spare Wheel Lug Nut | 40-80 ft-lbs | |
| Tire Pressure Sensor/Transmitter Mounting Nut | 71 in-lbs |
New in Jeep JK Wrangler Exterior Parts
This document contains the torque specifications for the screws, nuts, and bolts found throughout your tub, from the body mounts to the hinges and from the seat belts to the hardtop bolts. Your tub is the most significant component of your Jeep; it encompasses the full body of the vehicle from the bulkhead to the tailgate.
| Description | Specification | |
|---|---|---|
| Backlite Hinge Bolts | 90 in-lbs | |
| Body Isolator Mounting Bolts | 80 ft-lbs | |
| Body Isolator To Body Nuts | 40 ft-lbs | |
| Brake Booster Bracket Nuts | 13.5 ft-lbs | |
| Center Occupant Classification Systems Strain Gauge Stud Nut | 33 ft-lbs | |
| Door Carrier Plate Screws | 90 in-lbs | |
| Door Hinge Pin Nut | 75 in-lbs | |
| Door Hinge To Body Bolts | 21 ft-lbs | |
| Door Hinge To Hinge Bolts | 19 ft-lbs | |
| Door Latch Adjustment Screw | 26.5 in-lbs | |
| Door Latch Mounting Screws | 71 in-lbs | |
| Door latch Striker Bolts | 19 ft-lbs | |
| Four Door Rear Seat 40% Inner Seat Back Pivot Nut | 18.5 ft-lbs | |
| Four Door Rear Seat Center Belt buckle Bolt | 45 ft-lbs | |
| Four Door Rear Seat Cushion Pivot Bolts | 18.5 ft-lbs | |
| Four Door Rear Seat Front Mounting Fasteners | 45 ft-lbs | |
| Four Door Rear Seat Headrest Bolts | 71 in-lbs | |
| Four Door Rear Seat Inner Latch Floor Bolts | 18.5 ft-lbs | |
| Four Door Rear Seat Latch To Back Frame Bolts | 33 ft-lbs | |
| Four Door Rear Seat Outboard Latch Floor Bolts | 18.5 ft-lbs | |
| Four Door Rear Seat Rear Mounting Bolt | 45 ft-lbs | |
| Four Door Rear Seat Rear Mounting Nuts | 62.5 ft-lbs | |
| Four Door Rear Seat Seat Cushion Pivot Bolt | 18.5 ft-lbs | |
| Four Door Retractor Screw | 41 ft-lbs | |
| Four Door Seat Cushion Pivot Bolt | 18.5 ft-lbs | |
| Front Door Exterior Handle Nut | 40 in-lbs | |
| Front Door Glass Run Nut | 90 in-lbs | |
| Front Door Interior Handle Screw | 75 in-lbs | |
| Front Seat Back Assembly Bolts | 34.5 ft-lbs | |
| Front Seat Belt Anchor Bolt | 29.5 ft-lbs | |
| Front Seat Belt Buckle Bolt | 37 ft-lbs | |
| Front Seat Belt Turning Loop Screw | 29.5 ft-lbs | |
| Front Seat Mounting Bolts | 45 ft-lbs | |
| Front Seat Riser Nuts | 21 ft-lbs | |
| Half Door Latch Nut | 40 in-lbs | |
| Hard Top Front Bolts | 93 in-lbs | |
| Hard Top Side Bolts | 13 ft-lbs | |
| Hood Catch Bracket Nuts | 62 in-lbs | |
| Hood Catch Nuts | 11 ft-lbs | |
| Hood Hinge To Body Bolts | 18 ft-lbs | |
| Hood Hinge To Hood Bolts | 19 ft-lbs | |
| Hood Safety Catch Bolt | 8 ft-lbs | |
| Instrument Panel Center Support Bracket Fasteners | 6 ft-lbs | |
| Instrument Panel Fence Line Nuts | 9 ft-lbs | |
| Instrument Panel Side Support Bolts | 8 ft-lbs | |
| Lower Fender To Sill Bolts | 9 ft-lbs | |
| Manual Shifter Bolt | 24.5 ft-lbs | |
| Occupant Classification System Riser Nuts | 21 ft-lbs | |
| Outside Rearview Mirror Bolts | 10 ft-lbs | |
| Rear Door Exterior Handle Nut | 40 in-lbs | |
| Rear Door Glass Run Bolt | 9 ft-lbs | |
| Rear Door Glass Run Nut | 90 in-lbs | |
| Rear Door Interior Handle Screw | 75 in-lbs | |
| Rear view Mirror Set Screw | 18 in-lbs | |
| Seat Side Airbag Nuts | 62 in-lbs | |
| Side Step Bracket Bolts | 18 ft-lbs | |
| Side Step Sill Nuts | 9 ft-lbs | |
| Soft Top Pivot Knuckle Bolts | 10 ft-lbs | |
| Speaker Pod Screws | 90 in-lbs | |
| Sport Bar Cross Bar Bracket Bolts | 14 ft-lbs | |
| Sport Bar Front Cross Bar Bracket Bolts | 14 ft-lbs | |
| Sport Bar Rear Bolts | 14 ft-lbs | |
| Sport Bar Rear Cross Bar Bracket Bolts | 14 ft-lbs | |
| Sport Bar Side Bar Bolts | 14 ft-lbs | |
| Sport Bar Side Bar To Windshield Frame Bolts | 17 ft-lbs | |
| Sport Bar To B-pillar Bolts | 14 ft-lbs | |
| Steering Column Opening Reinforcement Plate Bolts | 8 ft-lbs | |
| Tailgate Exterior Handle Nuts | 40 in-lbs | |
| Tailgate Hinge To Body Bolts | 19ft-lbs | |
| Tailgate Hinge To Tailgate Bolts | 15ft-lbs | |
| Tailgate Latch Screws | 71 in-lbs | |
| Tailgate Stabilizer Insert And Cup Bolts | 90 in-lbs | |
| Tailgate Striker Bolts | 21ft-lbs | |
| Two Door Rear Seat Back Frame To Cushion Bolts | 37ft-lbs | |
| Two Door Rear Seat Back Latch Bolts | 33ft-lbs | |
| Two Door Rear Seat Center Belt Buckle Bolt | 41ft-lbs | |
| Two Door Rear Seat Cushion To Back Bolts | 37ft-lbs | |
| Two Door Rear Seat Front Latch Cushion Frame Bolts | 33ft-lbs | |
| Two Door Rear Seat Rear latch Nuts | 90 in-lbs | |
| Upper Fender Fasteners | 44 in-lbs | |
| Windshield Frame Hinge To Body Bolts | 15ft-lbs | |
| Windshield Frame Reinforcement Bracket Bolts | 15ft-lbs |
Most Popular JK Exterior Mods
If you feel the need to tighten the screws holding your lights in place, here are the manufacturer specs to refer to. In truth, they should just be tightened with a screwdriver; as long as you don’t try to use an impact wrench, you should be alright.
| Description | Specification |
|---|---|
| Center High Mounted Stop Lamp (Third Brake Light) Mounting Screws | 20 in-lbs |
| Front Fog Lamp Mounting Screws | 18 in-lbs |
| Left Multi-Function Switch Mounting Screw | 10 in-lbs |
| License Plate Bracket Mounting Screws | 15 in-lbs |
| Park Brake Switch Mounting Screw | 24 in-lbs |
| Rear Fog Lamp Mounting Screws | 27 in-lbs |
| Rear Lamp Unit Mounting Screws | 15 in-lbs |
Top Sellers
Take advantage of the best car repair knowledge availableAlldatadiy.com andEautorepair.net are professional-grade shop manuals, bar none! Wiring diagrams and technical service bulletins are among the documents available. The majority of the time, their diagrams are taken directly from the manufacturing manuals. Pricing: -Eautorepair.net membership for one month $19.95 per car, each day Subscription for one year $29.95 per car (plus applicable taxes). Subscription for a period of four years $44.95 per car, each day -Alldatadiy.com: a one-year $29.95 membership that allows you to add more automobiles.
- Additional cars are included in the $49.95 membership for five years.
- If you’re trying to figure out what’s wrong with your wiring, Eautorepair.netis the superior option.
- This saves a significant amount of time because you don’t have to refer back to the component locator or circuit locations as often.
- To learn the identification symbols, you must first consult the factory legends, and then you must consult circuit diagrams in order to determine the placement of the splice and ground points.
You should utilize Alldatadiy.com instead of Eautorepair.net if you need to rummage about in your doors, dashboard, or console since Eautorepair.net does not provide interior or exterior trim or body part removal.
Lug Nut Torque Specs – International Full Size Jeep Association
| King Browless | Join Date: Nov 30, 2001Location: Fort Wayne, IndianaPosts: 6,534 |
| Lug Nut Torque Specs
From what I have gathered, the torque specs for the 9/16″ lug nuts on my J20 is 135-145 ft/lbs each.This seems to be a lot.What is the proper recommended torque specs for my J20?_Bryan Smith 2005 Grand Cherokee Limited – HEMI!Current Daily Driver1982 J10: Stalled Project.1981 J20: Commercial flat bed. Lost in Divorce1987 J20 Pioneer: Former ‘Ricbee’ plow rig. RUST!Quote:Originally Posted byJayrodoh.but if it works, I wouldn’t touch it.Quote:Originally Posted byLindelBest laid plans, yada yada yada. |
| FSJ Maniac | Join Date: Jan 08, 2003Location: Centennial, ColoradoPosts: 2,907 |
| Quote:Originally Posted byThe PIG SmithFrom what I have gathered, the torque specs for the 9/16″ lug nuts on my J20 is 135-145 ft/lbs each.This seems to be a lot.What is the proper recommended torque specs for my J20?I donno for sure but I’d think it’d be based on size of stud. here’s what the tirerack page sez.That does seem like a lot, but.?It also sounds familiar.Course I don’t have a J20 so what do I know. *shrug*Michael_Broken Photobucket image in my post?PM me. 1986 Grand Wagoneer”Troubled Child”tc.wagoneer.orgFacebookKØFSJStock 360, TBI, 727 with TransGo, NP208, 4″ Skyjacker, 33″ BFG MT, WT Axles, Lock RightARB, OBA |
| King Browless | Join Date: Nov 30, 2001Location: Fort Wayne, IndianaPosts: 6,534 |
| Here is a Bump for more discussion_Bryan Smith 2005 Grand Cherokee Limited – HEMI!Current Daily Driver1982 J10: Stalled Project.1981 J20: Commercial flat bed. Lost in Divorce1987 J20 Pioneer: Former ‘Ricbee’ plow rig. RUST!Quote:Originally Posted byJayrodoh.but if it works, I wouldn’t touch it.Quote:Originally Posted byLindelBest laid plans, yada yada yada. |
| 10-01-2007, 08:48 PM |
| When I worked at Sears Auto Center all cars got 100ft lbs (‘cept Hondas and little little cars) and most heavier/medium trucks got 125ft lbs._-Jonny B.1979 Cherokee Golden Eagle-UNDER CONSTRUCTION 7″ Alcan springs, BJ’s HD shackles – 35×12.5×15 BFG Mud TerrainsAMC 401 – Pro-Flo 4 EFINV4500/NWF BB/NP205 – Triple Stick’dF D44 – 4.10, Eaton E-LockerR M23 – 4.10, Detroit Locker1979 Cherokee Chief- Parts1979 Cherokee Chief- Parts1979 Wagoneer- Sold1981 Cherokee Chief- Cubed |
| 10-01-2007, 09:32 PM |
| 90ft lbs for 5 and 6 lug FSJ’s, I generally do 125 for 8 luggers. |
| FSJ Maniac | Join Date: Mar 04, 2006Location: Lima,Ohio/Piedmont, OhioPosts: 3,145 |
| wagoneer, cherokee, and truck (except 8400 gvw):75 ft/lbsTruck (8400): 130 ft/lbsstrait outa the 79 owners manual_JeeplessIn to Turbo crap now |
| Posting Rules |
| Youmay notpost new threadsYoumay notpost repliesYoumay notpost attachmentsYoumay notedit your posts
vB codeisOnSmiliesareOncode isOnHTML code isOff |
Lug nut torque
10:01 a.m. on October 23, 2008 Starter for the MMemberThread Date of joining: August 2008 posts 155 likes 0 received 0 likeson0 posts 155 posts 155 likes 0 likeson0 posts 155 posts Model:Cherokee Torque applied to the lug nut What would be the proper lug nut torque setting? should be used in conjunction with Jeep original factory wheels At this time, I do not have an ownersmanual or an ahayes manual. thanks On October 23, 2008, at 12:51 p.m., Renix Super Guru is a term used to describe a person who has achieved greatness.
Number of posts: 24,653Number of likes: 0 Year:1990XJ/1989MJ Model:Comanche Engine:4.0L Renix I’ve searched in both the Haynes and the FSM, and not one of them provides a number.
If you have aluminum wheels, the torque ranges from 75 to 105 ft/lbs.
MemberJoined on September 8, 2008 Afghanistan is the location.
Year:95 Model:CherokeeEngine:4.0Aaaand, after the first 50 miles or so, the aluminum wheels will need to be retorqued to ensure proper alignment.
MemberThread StarterJoined the group on August 8, 2008.
then re-evaluate them after 50 kilometers This is a great suggestion!
Date of joining: March 2008 Location: As stated in your postez fissin jurr spelinzs fissin jurr spelinzs fissin jurr spelinzs Number of posts: 24,653 0 people have expressed an interest.
Also stated in the owner’s handbook, “If you ever forget, I know I do” (I know I do).
Take a look at his post.
On October 23, 2008, at 9:52 p.m., Junior MemberJoined in September of 2008Location: Ottawa, Ontario Posts: 75Likes: 0Received: 0Received: 0 0 people like this.
Year:1996 The Cherokee is a model with a 4.0L engine.
on October 23, 2008 Senior MemberJoined in May 2008; resides in Michigan The year is 1996, and there are 814 posts with zero likes.
80 to 110 ft lbs.
Seasoned MemberJoined the group in June of 2008.
Year:2001 Model:Cherokee Engine:4.0 Torque applied to the lug nut As a former tire technician and current employee of a Jeep dealership, I would recommend at least 100 ft/lbs, especially if you wheel it.
BlueXJ last revised this post on 10-24-2008 at 10:56 AM.
On October 24, 2008, at 10:39 a.m.
Model:Cherokee Okay, one hundred foot pounds is the answer.
Tuesday, February 10th, 4:21 p.m.
No likes have been received, and no likes have been given on any of the posts.
(130 N-m.) I just thought I’d throw that one out there for good measure!
12:12 p.m.
At 2:40 PM, SteveMongr Cherokee Chat610-22-2015 (Chat 610-22-2015) 11:00:05 p.m.
XJ Cherokee Raney120StockXJ Cherokee Tech.
All non-modified/stock XJ inquiries should be directed here. 12:27 p.m. on Tuesday, October 16, 2015 StabsthedramaCherokee Chat810-01-201507:34 PM StabsthedramaCherokee Chat810-01-201507:34 PM Users that are currently active on this thread are: 1 (0 members and 1 guests)